DOWNLOAD Sony DCR-TRV360 / DCR-TRV361 / DCR-TRV460 / DCR-TRV460E / DCR-TRV461E (serv.man2) Service Manual ↓ Size: 5.27 MB | Pages: 62 in PDF or view online for FREE

1-5

E

E

E

E

Block

Function

6

1

6

1

6

2

6

2

Detailed

Code

0

0

1

0

0

0

0

1

Symptom/State

Difficult to adjust focus
(Cannot initialize focus.)

Zoom operations fault
(Cannot initialize zoom lens.)

Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)

Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)

Self-diagnosis Code

Repaired b

y:

Correction

Inspect the lens block focus reset sensor (Pin qs  of CN1551 of
VC-345 board) when focusing is performed when the control dial
is rotated in the focus manual mode and the focus motor drive circuit
(IC1554 of VC-345 board) when the focusing is not performed.

Inspect the lens block zoom reset sensor (Pin qg  of CN1551 of
VC-345 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC1554 of VC-
345board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE752 of SI-041 board)
peripheral circuits.

Inspect yaw angular velocity sensor (SE751 of SI-041 board)
peripheral circuits.

“1-5. CHANGE OF IC4501” is not shown.
Pages 1-6 is not shown.

2-1

2-2

The following flow chart shows the disassembly procedure.

NS knob

Note: When you remove Cabinet (R) Block,

or when you assembly, please slide
NS knob to the position of "ON".

Note: Flexible board is connected.

1

Lock ace 

x3

2

Cabi (upper)

3

Grip belt

4

Lock ace 

x3

5

Cabi (L)

1

Lock ace 

x6

2

NS knob to the position of "ON".

3

Cabi (R)

4

VC-345: CN1007

5

VC-345: CN1003

6

VC-345: CN1008

1

Tripod Screw

2

Tapping P2 

x2

3

Tapping P2 

x6

4

Claw

5

CF-5100

6

Tapping P2 

x4

7

Claw 

x2

8

P Cabi (C)

9

Tapping P2 

x2

q;

Tapping P2 

x1

qa

P Cabi (M)

qs

PD-205: CN6005

qd

PD-205: CN6001

qf

PD-205, LCD901, ND901

qg

Tapping P2 

x4

qh

Hinge assy

6

Lock ace 

x3

7

Claw

8

Front panel

9

FP-796: CN754, CN1001

1

Lift up the EVF.

2

Tapping P2 

x4

3

Down the EVF.

4

EVF block

5

EVF Cabi (upper)

6

EVF Cabi (lower)

7

FP-797: LCD902

8

EVF lens

1

Tapping P2 

x4

2

Claw 

x2

3

P Cabi (C)

1

VC-345: CN1013

2

VC-345: CN1016

3

VC-345: CN4001

4

Lock ace 

x3

5

EVF/Battely panel block

6

VC-345: CN1009

7

Tapping P2 

x1

8

Lock ace 

x1

9

SS-5100

1

VF blind sheet

2

VC-345: CN2403, CN2404, CN3201

3

VC-345: CN2401

4

Screw (M1.7) 

x2

5

Claw

6

Open the VC-345.

7

VC-345: CN2402

8

VC-345

1

Screw (M1.7) 

x3

2

CS frame

1

VC-345: CN1501

2

VC-345: CN1551

3

Lens sheet

4

Lock ace 

x2

5

Boss

6

Lens LSV-820A

1

5

2

1

3

4

4

6

6

7

9

8

1

1

2

4

5

6

3

qd

qg

2

3

4

6

7

9

q;

qs

1

5

4

4

7

8

1

3

2

2

3

4

5

6

7

8

1

1

1

2

5

6

9

4

1

2

3

5

6

8

qa

qf

qh

1

2

2

3

4

7

5

6

2

1

3

8

A

B

Adjustment remote
commander (RM-95)

Info lithium battery
(L series)

I/F unit for LANC control
(J-6082-521-A)

CPC jig connector
(J-6082-539-A)

Cabinet R block

EVF block/
Battery panel block assembly

Mechanism deck

Control key block
(SS-5100)

VC-345 board

Front panel block

Lens block

Press the cassette compartment 
in the direction of the arrow 

A

 

to move it up in the direction of 
the arrow 

B

.

Contacting
surface

Eject switch

When exiting the "Forced Power ON" mode, connect the control
key block (SS-5100) to the CN1009 of VC-345 board. Or, when
ejecting the cassette, connect the control key block (SS-5100) to
the CN1009 of VC-345 board. and press the Eject switch.

To check the mechanism deck, set the Camera or VTR to the "Forced power ON" mode. (Or, connect the control key
block (SS-5100) to the CN1009 of VC-345 board and set the power switch to the "CAMERA" or "PLAY/edit" position.)
Operate the Camera functions of the zoom and focus, the VTR function using the adjustment remote commander
(with the HOLD switch set in the OFF position).

1)  Select page: 0, address: 01, and set data: 01.
2)  Select page: A, address: 10, set data: 02 and 

press the PAUSE button of the adjustment remote
commander.

1)  Select page: 0, address: 01, and set data: 01.
2)  Select page: A, address: 10, set data: 02 and 

press the PAUSE button of the adjustment remote
commander.

1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, data: 00, and press the PAUSE 

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

AC adaptor

AC IN

1

5

2

1

3

4

4

6

6

7

9

8

1

1

2

4

5

6

3

4

4

7

8

1

3

2

2

3

4

5

6

7

8

1

1

1

2

5

6

9

4

1

2

3

5

6

2-3

2-4