Sony DCR-TRV33 / DCR-TRV33E (serv.man4) Service Manual ▷ View online
6-26
DCR-TRV33/TRV33E
9. Color Reproduction Adjustment
Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Video terminal of AUDIO/VIDEO jack
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
37, 39, 40, 41
Specified Value
All color luminance points should settle
within each color reproduction frame.
within each color reproduction frame.
Note1:
The data of page: 0, address: 10 must be “00”.
Note2:
NTSC model: DCR-TRV33
PAL model: DCR-TRV33E
PAL model: DCR-TRV33E
Switch setting:
1)
1)
POWER .................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
FOCUS (Function setting) .................................... MANUAL
4)
DIGITAL ZOOM (Menu setting) .................................... OFF
5)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 6, address: 9D, and set data: 18.
3)
Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.
button.
4)
Select page: F, address: F0, set the following data, and press
the PAUSE button.
the PAUSE button.
37 (NTSC), B7 (PAL)
5)
Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
the burst luminance point to the burst position of the color
reproduction frame.
6)
Change the data of page: F, address: 37, 39, 40 and 41, and settle
each color luminance point in each color reproduction frame.
each color luminance point in each color reproduction frame.
Note:
Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
commander before changing the addresses. If not, the new data
will not be written to the memory.
Processing after Completing Adjustments:
1)
1)
Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
button.
2)
Select page: 6, address: 9D, and set data: 00.
3)
Select page: 0, address: 01, and set data: 00.
Burst position
For NTSC model
Burst position
For PAL model
Fig. 6-1-12.
6-27
DCR-TRV33/TRV33E
10. Auto White Balance Standard Data Input
Adjust the white balance reference at 3200K.
Adjust the white balance reference at 3200K.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
1E (Note)
Adjustment Address
2E to 31
E8 to F3
Note1: This adjustment should be carried out upon completion of “Color
reproduction adjustment”.
Note2: When reading or writing the 1E page data, select page:0,address:10,
and set data: 01, then select E page. The 1E page can be chosen by
this data setting.
After reading or writing, reset the data of page: 0, address: 10 to “00”.
this data setting.
After reading or writing, reset the data of page: 0, address: 10 to “00”.
Note3: After the power is turned on, this adjustment can be done only
once.
Note4: Check that the data of page: 6, address: 02 is “00”. If not, turn off
the power and turn on again.
Switch setting:
1)
1)
POWER .................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
FOCUS (Function setting) .................................... MANUAL
4)
DIGITAL ZOOM (Menu setting) .................................... OFF
5)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
Wait for more than 2 sec.
4
6
01
11
Set the data, and press PAUSE
button.
button.
5
6
01
0B
Set the data, and press PAUSE
button.
button.
6
6
02
Check that the data changes to
“01”. (Note4)
“01”. (Note4)
Note5: The adjustment data will be automatically input to page: F, address:
2E to 31 and to page: 1E, address: E8 to F3.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
0
01
00
Set the data.
3
Perform “LV Standard Data
Input”.
Input”.
11. LV Standard Data Input
Adjust the normal coefficient of the light value.
Adjust the normal coefficient of the light value.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Display data of page 1 (Note5)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
1A, 1B
Specified Value
0FE0 to 1020
Note1: This adjustment should be carried out upon completion of “Color
Reproduction Adjustment”.
Note2: After the power is turned on, this adjustment can be done only
once.
Note3: The data of page: 0, address: 10 must be “00”.
Note4: Check that the data of page: 6, address: 02 is “00”. If not, turn off
Note4: Check that the data of page: 6, address: 02 is “00”. If not, turn off
the power and turn on again.
Note5: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Display data
Switch setting:
1)
1)
POWER .................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
FOCUS (Function setting) .................................... MANUAL
4)
DIGITAL ZOOM (Menu setting) .................................... OFF
5)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
Wait for more than 2 sec.
3
6
01
0D
Set the data, and press PAUSE
button.
button.
4
6
02
Check that the data changes to
“01”. (Note6)
“01”. (Note6)
5
0
03
1E
Set the data.
6
1
Check that the display data (Note5)
satisfies the specifiedvalue.
satisfies the specifiedvalue.
Note6: The adjustment data will be automatically input to page: F, address:
1A, 1B.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
0
03
00
Set the data.
3
0
01
00
Set the data.
4
Perform “Auto White Balance
Adjustment”.
Adjustment”.
Ver 1.1 2004. 05
6-28
DCR-TRV33/TRV33E
12. Auto White Balance Adjustment
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
Filter C14 for color temperature
correction
correction
Measurement Point
Display data of page 1 (Note3)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
1E (Note)
Adjustment Address
32 to 35
F4 to FF
Specified Value
R ratio: 2C2C to 2CAC
B ratio: 5AE8 to 5B68
B ratio: 5AE8 to 5B68
Note1: This adjustment should be carried out upon completion of “Auto
White Balance Standard Data Input”.
Note2: After the power is turned on, this adjustment can be done only
once.
Note3: When reading or writing the 1E page data, select page: 0, address:
10, and set data: 01, then select E page. The 1E page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note4: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Display data
Switch setting:
1)
1)
POWER .................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
FOCUS (Function setting) .................................... MANUAL
4)
DIGITAL ZOOM (Menu setting) .................................... OFF
5)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Place the C14 filter for color
temperature correction on the lens.
temperature correction on the lens.
2
0
01
01
Set the data.
3
0
10
00
Set the data.
4
F
44
Write down the data.
5
F
44
2C
Set the data, and press PAUSE
button.
button.
6
F
45
Write down the data.
7
F
45
6C
Set the data, and press PAUSE
button.
button.
8
F
46
Write down the data.
9
F
46
5B
Set the data, and press PAUSE
button.
button.
10
F
47
Write down the data.
11
F
47
28
Set the data, and press PAUSE
button.
button.
12
6
01
83
Set the data, and press PAUSE
button.
button.
13
6
01
81
Set the data, and press PAUSE
button.
button.
14
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
15
6
01
3F
Set the data, and press PAUSE
button.
button.
16
0
03
04
Set the data.
17
1
Check that the display data
(Note4) satisfies the R ratio
specified value.
(Note4) satisfies the R ratio
specified value.
18
0
03
05
Set the data.
19
1
Check that the display data
(Note4) satisfies the B ratio
specified value.
(Note4) satisfies the B ratio
specified value.
Note5: The adjustment data will be automatically input to page: F, address:
32 to 35 and to page: 1E, address: F4 to FF.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
F
44
Set the data that is written down
at step 4, and press PAUSE
button.
at step 4, and press PAUSE
button.
3
F
45
Set the data that is written down
at step 6, and press PAUSE
button.
at step 6, and press PAUSE
button.
4
F
46
Set the data that is written down
at step 8, and press PAUSE
button.
at step 8, and press PAUSE
button.
5
F
47
Set the data that is written down
at step 10, and press PAUSE
button.
at step 10, and press PAUSE
button.
6
6
01
00
Set the data, and press PAUSE
button.
button.
7
0
01
00
Set the data.
8
0
03
00
Set the data.
Ver 1.1 2004. 05
6-29
DCR-TRV33/TRV33E
13. White Balance Check
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
Filter C14 for color temperature
correction ND filter 1.0 and 0.4 and 0.1
Measurement Point
Video terminal of AUDIO/VIDEO jack
Measuring Instrument
Vectorscope
Specified Value
Fig. 6-1-13. A to B
Note1:
The data of page: 0, address: 10 must be “00”.
Switch setting:
1)
1)
POWER .................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
FOCUS (Function setting) .................................... MANUAL
4)
DIGITAL ZOOM (Menu setting) .................................... OFF
5)
STEADY SHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data
Procedure
Indoor white balance check
1
Check that the lens is not
covered with either filter.
covered with either filter.
2
6
01
0F
Set the data, and press PAUSE
button.
button.
3
Check that the center of the
white luminance point is within
the circle shown Fig. 6-1-13. A.
white luminance point is within
the circle shown Fig. 6-1-13. A.
4
6
01
00
Set the data, and press PAUSE
button.
button.
Outdoor white balance check
5
Place the C14 filter on the lens.
6
6
01
3F
Set the data, and press PAUSE
button.
button.
7
Check that the center of the
white luminance point is within
the circle shown Fig. 6-1-13. B.
white luminance point is within
the circle shown Fig. 6-1-13. B.
8
Remove the C14 filter.
LV data check
9
Place the ND filter 1.5
(1.0+0.1+0.4) on the lens.
(1.0+0.1+0.4) on the lens.
10
6
01
00
Set the data, and press PAUSE
button.
button.
11
0
03
06
Set the data.
12
1
Check that the display data
(Note2) satisfies the specified
value.
Specified value: 8000 to 8BC0
(Note2) satisfies the specified
value.
Specified value: 8000 to 8BC0
Note2:
Displayed data of the adjustment remote commander.
1 : XX : XX
Display data
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
0
03
00
Set the data.
Fig. 6-1-13 (A).
Fig. 6-1-13 (B).
R-Y
2mm
B-Y
2mm
R-Y
B-Y
1mm
1mm
3mm
3mm
Click on the first or last page to see other DCR-TRV33 / DCR-TRV33E (serv.man4) service manuals if exist.