Sony DCR-TRV255E / DCR-TRV260 / DCR-TRV265 / DCR-TRV265E Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DCR-TRV255E/TRV260/TRV265/TRV265E
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
1-2. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
The following method is available to prevent this.
that the unit cannot operate.
The following method is available to prevent this.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
1-2
DCR-TRV255E/TRV260/TRV265/TRV265E
1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Refer to “SECTION 2. DISASSEMBLY” to remove the mechanism deck block.
2
Disconnect CN2401 (2P) of VC-344 board.
3
Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette compartment.
4
Pull the timing belt in the direction of
arrow
arrow
A
with a pincette while pressing
the cassette compartment (take care
not to damage) to adjust the bending
of a tape.
not to damage) to adjust the bending
of a tape.
5
Let go your hold the cassette
compartment and rise the cassette
compartment to take out a cassette.
compartment and rise the cassette
compartment to take out a cassette.
Pincette
Timing belt
Timing belt
Press the cassette compartment not to
rise the cassette compartment
rise the cassette compartment
[DC power supply]
(+5V)
Adjust the bending of a tape
Disconnect CN2401
of VC-344 board.
of VC-344 board.
Loading motor
A
A
1-3
DCR-TRV255E/TRV260/TRV265/TRV265E
1-4. LCD TYPE CHECK
The LCD type can be checked with data value by connecting the adjustment remote commander.
Note:
About PD-204 board and LCD module, discriminate LCD type on the machine, and replace the same type.
Preparations:
1) Connect the equipment for adjustments according to Fig. 1.
2) Connect the adjustment remote commander to VC-344 board CN1011 via I/F unit for LANC control (J-6082-521-A) and CPC jig
1) Connect the equipment for adjustments according to Fig. 1.
2) Connect the adjustment remote commander to VC-344 board CN1011 via I/F unit for LANC control (J-6082-521-A) and CPC jig
connector (J-6082-539-A).
To operate the adjustment remote commander, connect the AC power adaptor to the DC IN jack of I/F unit for LANC control, or connect
the L series Info-LITHIUM battery to the battery terminal of I/F unit for LANC control.
To operate the adjustment remote commander, connect the AC power adaptor to the DC IN jack of I/F unit for LANC control, or connect
the L series Info-LITHIUM battery to the battery terminal of I/F unit for LANC control.
Checking method:
1) Select page: 3, address: CC.
2) By checking the data value of display data, the type of LCD can be discriminated.
1) Select page: 3, address: CC.
2) By checking the data value of display data, the type of LCD can be discriminated.
Data
LCD type
64 to 67
TYPE C
40 to 43
TYPE S
CN1011
16
1
AC IN
AC adaptor
AC adaptor
CPC lid
I/F unit for LANC control
(J-6082-521-A)
(J-6082-521-A)
Conductor side
L serices Info
LITHIUM battery (7.2Vdc)
LITHIUM battery (7.2Vdc)
Adjustment
remote commander (RM-95)
remote commander (RM-95)
CPC jig connector
(J-6082-539-A)
(J-6082-539-A)
LANC jack
AC IN
Screw (M2)
1-4
DCR-TRV255E/TRV260/TRV265/TRV265E
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or Display
window what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder or Display
window what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or Display window shows a 4-digit display consisting
of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
viewfinder or Display window shows a 4-digit display consisting
of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
1-5-3. Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
1.
Display Method
While pressing the “STOP” key, set the switch from OFF to “ON”, and continue pressing the “STOP” key for 5 seconds continuously. The
service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
[3] : Occurred third time
[5] : Occurred fifth time
[2] : Occurred second time
[4] : Occurred fourth time
[6] : Occurred the last time
3.
End of Display
Turning OFF the power supply will end the service mode display.
Order of previous errors
Backup No.
Self-diagnosis Codes
C : 3 1 : 1 1
[3]
Lights up
Viewfinder
[3] C : 3 1 : 1 1
3 C : 3 1 : 11
Display window
1 1
3 1
C : 3 1 : 11
C
Repaired by:
Refer to “1-5-4. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder
Display window
C : 3 1 : 1 1
Control Dial
Note: The “self-diagnosis display” data will not be erased (reset), when the lithium battery (CONTROL KEY BLOCK (CF-
5100): BT001) is removed.
Click on the first or last page to see other DCR-TRV255E / DCR-TRV260 / DCR-TRV265 / DCR-TRV265E service manuals if exist.