DOWNLOAD Sony DCR-TRV255E / DCR-TRV260 / DCR-TRV265 / DCR-TRV265E (serv.man3) Service Manual ↓ Size: 1.67 MB | Pages: 56 in PDF or view online for FREE

6-19

Correct a deviation of optical axis between the lens and the CCD
imager.
If deviated, the screen center will be shifted when the lens is
zoomed from TELE end to WIDE end.

Subject

Siemens Star

Measurement Point

Check operation on monitor TV

Measuring Instrument

Adjustment Page

F

Adjustment Address

5A

Check that the data of page: 0, address: 10 is “00”.

“Flange Back Adjustment” must be already finished.

Switch setting:
1) DIGITAL ZOOM (Menu setting) .................................... OFF
2) STEADYSHOT (Menu setting) ...................................... OFF
3) DISPLAY (Menu setting) ................................................ LCD

Preparation for adjustment:
1) Play a monoscope portion of the System Check tape (WR5-

5NSP (NTSC) or WR5-5CSP (PAL)).

2) Stick the optical axis deviation specification frame to the moni-

tor screen so that the center of monoscope coincides with the
center of specification frame.

3) Select the CAMERA mode.

Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 5A, and set data: 00, then press the

PAUSE button on the adjusting remote commander.

3) Place the Siemens Star at 2 m position away from the lens.
4) Shoot the Siemens Star with the zoom at TELE end.
5) Change the lens direction so that the center of Siemens Star

coincides with the center of optical axis deviation specifica-
tion frame.

6) Shoot the Siemens Star with the zoom at WIDE end.
7) Check on the monitor TV which area the center of Siemens

Star exists of the optical axis deviation specification frame.
At this time, measure the amount of deviation “L1” (distance
from the center of Siemens Star to the center of optical axis
deviation specification frame).

8) From the following table, read correction data according to

the area.

0

180

90

67.5

22.5

337.5

292.5

247.5

202.5

157.5

112.5

8

4

5

7

1

6

2

3

270

Area

1

2

3

4

5

6

7

8

Deviation Phase

22.6

° to 67.5°

67.6

° to 112.5°

112.6

° to 157.5°

157.6

° to 202.5°

202.6

° to 247.5°

247.6

° to 292.5°

292.6

° to 337.5°

337.6

° to 22.5°

Correction Data

01

02

03

04

05

06

07

08

9) Select page: F, address: 5A, and set correction data, then press

the PAUSE button on the adjusting remote commander.

10) Shoot the Siemens Star with the zoom at TELE end.
11) Change the lens direction so that the center of Siemens Star

coincides with the center of optical axis deviation specifica-
tion frame.

12) Shoot the Siemens Star with the zoom at WIDE end.
13) Measure the amount of deviation “L2” (distance from the cen-

ter of Siemens Star to the center of optical axis deviation speci-
fication frame).

14) Compare L1 and L2, and make sure that the L2 is smaller than

L1.
If large, select page: F, address: 5A, and set data: 00, then
press the PAUSE button on the adjusting remote commander.

Processing after completion of adjustment:
1) Select page: 0, address: 01, and set data: 00.

6-20

A=B

C=D

A

B

C

D

E=F

V

E

F

Color bar chart picture frame

Monitor TV picture frame

Mode

CAMERA

Subject

Color bar chart
(Color reproduction adjustment
frame)
(1.0 m from the front of lens)

Measurement Point

Video terminal of A/V OUT jack
(75 

Ω terminated)

Measuring Instrument

Oscilloscope and monitor TV

Specified Value

A=B, C=D, E=F

Check that the data of page: 0, address: 10 is “00”.

Perform “Flange Back Adjustment” and “Optical Axis
Adjustment” before this adjustment.

Switch setting:
1) DIGITAL ZOOM (Menu setting) .................................... OFF
2) STEADYSHOT (Menu setting) ...................................... OFF
3) DISPLAY (Menu setting) ................................................ LCD

Setting method:
1) Select page: 6, address: 48, and set data: 01.
2) Adjust the zoom and the camera direction, and set to the speci-

fied position.

3) Mark the position of the picture frame on the monitor display,

and adjust the picture frame to this position in following ad-
justments using “Color reproduction adjustment frame”.

Processing after completing camera system adjustments:
1) Select page: 6, address: 48, and set data: 00.

6-21

R-Y

B-Y

R

B

G

M

G

Y

E

C

Y

Burst

R-Y

B-Y

R

B

G

M

G

Y

E

C

Y

Burst

Adjust the color separation matrix coefficient so that proper color
reproduction is produced.

Mode

CAMERA

Subject

Color bar chart
(Color reproduction adjustment
frame)

Measurement Point

Video terminal of A/V OUT jack
(75 

Ω terminated)

Measuring Instrument

Vectorscope

Adjustment Page

F

Adjustment Address

33, 35, 3A, 3B

Specified Value

All color luminance points should
settle within each color reproduction
frame.

Check that the data of page: 0, address: 10 is “00”.

Perform “Flange Back Adjustment” before this adjust-
ment.

NTSC model: DCR-TRV260/TRV265
PAL model: DCR-TRV255E/TRV265E

Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting) .................................... OFF
3) STEADYSHOT (Menu setting) ...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD

Order Page Address Data

Procedure

1

0

01

01

2

6

48

01

3

6

9D

86

4

6

01

3D

Press PAUSE button.

5

F

80

Set the following data, and
press PAUSE button.
37: NTSC model
B7: PAL model

6

Adjust the GAIN and
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.

7

F

Change the data and settle
each color luminance point in
each color reproduction
frame. (Note 4)

Be sure to press the PAUSE button of the adjusting re-
mote commander before changing the addresses. If not,
the new data will not be written to the memory.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

6

48

00

3

6

9D

00

4

0

01

00

33
35

3A
3B

6-22

Adjust the normal coefficient of the light value.

Mode

CAMERA

Subject

Clear chart
(Color reproduction adjustment frame)

Measurement Point

Displayed data of page: 1 (Note 4)

Measuring Instrument

Adjusting remote commander

Adjustment Page

F

Adjustment Address

1A, 1B

Specified Value

0FE0 to 1020

Perform “Flange Back Adjustment” before this adjust-
ment.

Check that the data of page: 0, address: 10 is “00”.

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

The right four digits of the page: 1 displayed data of the
adjusting remote commander.

1:XX:XX

Displayed data

Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting) .................................... OFF
3) STEADYSHOT (Menu setting) ...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD

Order Page Address Data

Procedure

1

0

01

01

2

6

48

01

3

6

01

0D

Press PAUSE button. (Note 5)

4

6

02

Check the data changes to
“01”.

5

0

03

1E

6

1

Check that the displayed data
(Note 4) satisfied specified
value.

The adjustment data will be automatically input to page:
F, address: 1A and 1B.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

6

48

00

3

0

03

00

4

0

01

00

Adjust the white balance reference at 3200K.

Mode

CAMERA

Subject

Clear chart
(Color reproduction adjustment frame)

Adjustment Page

F

Adjustment Address

2A to 2D

Perform “Color Reproduction Adjustment” before this
adjustment.

Check that the data of page: 0, address: 10 is “00”.

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting) .................................... OFF
3) STEADYSHOT (Menu setting) ...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD

Order Page Address Data

Procedure

1

0

01

01

2

6

48

01

3

6

01

11

Press PAUSE button.

4

6

01

0B

Press PAUSE button. (Note 4)

5

6

02

Check the data changes to
“01”.

The adjustment data will be automatically input to page:
F, address: 2A to 2D.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

6

48

00

3

0

01

00