Sony DCR-TRV250 (serv.man4) Service Manual ▷ View online
DCR-TRV250
6-11
4.
D Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
the A, D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, D Page Data”)
Address
Initial value
Remark
10
00
Test mode
11
Fixed data-1 (Initialized data)
12
13
Fixed data-2
14, 15
Fixed data-1 (Initialized data)
16
Fixed data-2
17 to 19
Fixed data-1 (Initialized data)
1A
1B
Fixed data-2
1C to 22
Fixed data-1 (Initialized data)
23
24
25
Fixed data-2
26
27 to 29
Fixed data-1 (Initialized data)
2A
2B
Fixed data-2
2C to 35
Fixed data-1 (Initialized data)
36
37
Fixed data-2
38
39
Fixed data-1 (Initialized data)
3A
Fixed data-2
3B to 58
Fixed data-1 (Initialized data)
59
Fixed data-2
5A to FF
Fixed data-1 (Initialized data)
DCR-TRV250
6-12
1-2-2.
Initialization of B, 1B Page Data
Note:
If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
1.
Initializing the B, 1B Page Data
Note 1:
If “Initialization of Pages B, 1B” is executed, all data on
pages B, 1B are initialized. (Only an individual page can-
not be initialized)
pages B, 1B are initialized. (Only an individual page can-
not be initialized)
Note 2:
If the B, 1B page data has been initialized, the following
adjustments need to be performed again.
1) Modification of B, 1B page data
adjustments need to be performed again.
1) Modification of B, 1B page data
Adjustment Page
B
Adjustment Address
00 to FF
Adjustment Page
1B
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
5
02
FF
4
5
01
F3
Press PAUSE button.
5
5
00
01
Press PAUSE button.
6
5
02
Check the data changes to “00”.
7
5
0E
00
Press PAUSE button.
8
5
03
20
Press PAUSE button.
9
5
01
FA
Press PAUSE button.
10
5
00
01
Press PAUSE button.
11
5
0E
Check the data changes to
“01”.
“01”.
12
Turn off the power supply,
then turn on them again.
then turn on them again.
13
Perform “Modification of B
Page Data”
Page Data”
2.
Modification of B, 1B Page Data
If the B, 1B page data has been initialized, change the data of the
“Fixed data-2” address shown in the following table by manual
input.
“Fixed data-2” address shown in the following table by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages B, set data: 00 to page: 0,
address: 10, and then select pages B.
3) If modification of data on pages 1B, set data: 01 to page: 0,
address: 10, and then select pages B. After the modification of
data finished, return the data on page: 0, address: 10 to “00”.
data finished, return the data on page: 0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification B, 1B page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
3.
B Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the B, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of B, 1B Page Data”)
the B, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of B, 1B Page Data”)
Address
Initial value
Remark
00 toFF
Fixed data-1 (Initialized data)
4.
1B Page table
Note 1:
If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the B, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of B, 1B Page Data”)
the B, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of B, 1B Page Data”)
Address
Initial value
Remark
00 to FF
Fixed data-1 (Initialized data)
DCR-TRV250
6-13
2.
Modification of 8, C, 18, 1C Page Data
If the 8, C, 18, 1C page data has been initialized, change the data
of the “Fixed data-2” address shown in the following table by
manual input.
of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages 8, C, set data: 00 to page: 0,
address: 10, and then select pages 8, C.
3) If modification of data on pages 18, 1C, set data: 01 to page:
0, address: 10, and then select pages 8, C. After the modifica-
tion of data finished, return the data on page: 0, address: 10 to
“00”.
tion of data finished, return the data on page: 0, address: 10 to
“00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification 8, C, 18, 1C page
data:
data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
1-2-3.
Initialization of 8, C, 18, 1C Page Data
Note:
If reading/writing data on pages 18, 1C, set data: 01 to
page: 0, address: 10, and then select pages 8, C. By this
data setting, the pages 18, 1C can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
page: 0, address: 10, and then select pages 8, C. By this
data setting, the pages 18, 1C can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
1.
Initializing the 8, C, 18, 1C Page Data
Note 1:
If “Initialization of Pages 8, C, 18, 1C” is executed, all
data on pages 8, C, 18, 1C are initialized. (Only an indi-
vidual page cannot be initialized)
data on pages 8, C, 18, 1C are initialized. (Only an indi-
vidual page cannot be initialized)
Note 2:
If the 8, C, 18, 1C page data has been initialized, the
following adjustments need to be performed again.
1) Modification of 8, C, 18, 1C page data
2) Electronic viewfinder system adjustments
3) LCD system adjustments
4) Node unique ID No. input
5) Servo, RF system adjustments
6) “S VIDEO OUT Y level adjustment” and “S VIDEO
following adjustments need to be performed again.
1) Modification of 8, C, 18, 1C page data
2) Electronic viewfinder system adjustments
3) LCD system adjustments
4) Node unique ID No. input
5) Servo, RF system adjustments
6) “S VIDEO OUT Y level adjustment” and “S VIDEO
OUT C level adjustment” of the video system ad-
justments
justments
7) Audio system adjustments
Adjustment Page
8
Adjustment Address
00 to FF
Adjustment Page
C
Adjustment Address
10 to FF
Adjustment Page
18
Adjustment Address
00 to FF
Adjustment Page
1C
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
81
10
4
3
80
0C
Press PAUSE button.
5
3
80
Check the data changes to
“1C”.
“1C”.
6
Perform “Modification of 8,
C, 18, 1C Page Data”
C, 18, 1C Page Data”
DCR-TRV250
6-14
4.
C Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Address
Initial value
Remark
10
EE
11
00
12
00
Switching position adj.
13
00
14, 15
Fixed data-1 (Initialized data)
16
E0
CAP FG duty adj.
17
E0
REEL FG adj.
18 to 24
Fixed data-1 (Initialized data)
25
80
S VIDEO OUT Y level adj.
26
70
27
50
S VIDEO OUT C level adj.
28 to 2E
Fixed data-1 (Initialized data)
2F
0E
REEL FG adj.
30 to 33
Fixed data-1 (Initialized data)
34
35
Fixed data-2
36
6F
37
5C
VCO adj. (EVF)
38
Fixed data-1 (Initialized data)
39
B3
RGB AMP adj. (EVF)
3A to 3D
Fixed data-1 (Initialized data)
3E
31
Contrast adj. (EVF)
3F
Fixed data-1 (Initialized data)
40
Fixed data-2
41 to 44
Fixed data-1 (Initialized data)
45
46
Fixed data-2
47
67
48
79
VCO adj. (LCD)
49
91
V-COM adj. (LCD)
4A
27
RGB AMP adj. (LCD)
4B
Fixed data-2
4C
A6
COM AMP adj. (LCD)
4D
87
4E
68
White balance adj. (LCD)
4F
4C
Contrast adj. (LCD)
50
Fixed data-2
51 to 53
Fixed data-1 (Initialized data)
54
Fixed data-2
55 to 60
Fixed data-1 (Initialized data)
61
62
Fixed data-2
63 to 9B
Fixed data-1 (Initialized data)
9C
Fixed data-2
3.
8 Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Address
Initial value
Remark
00 to 42
Fixed data-1 (Initialized data)
43
Fixed data-2
44 to FF
Fixed data-1 (Initialized data)
Click on the first or last page to see other DCR-TRV250 (serv.man4) service manuals if exist.