DOWNLOAD Sony DCR-TRV240E / DCR-TRV340E (serv.man3) Service Manual ↓ Size: 12.61 MB | Pages: 127 in PDF or view online for FREE

5-4

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

J-10

J-11

Filter for color temperature correction (C14)

ND filter 1.0

ND filter 0.4

ND filter 0.1

Pattern box PTB-450

Color chart for pattern box

Adjustment remote commander
(RM-95 upgraded) (Note1)

Siemens star chart

Clear chart for pattern box

Multi CPC jig

CPC-13 jig

Minipattern box

Camera base

J-6080-058-A

J-6080-808-A

J-6080-806-A

J-6080-807-A

J-6082-200-A

J-6020-250-A

J-6082-053-B

J-6080-875-A

J-6080-621-A

J-6082-311-A

J-6082-443-A

J-6082-353-B

J-6082-384-A

Auto white balance adjustment/check
White balance adjustment/check

White balance check

White balance check

White balance check

For checking the flange back

For adjusting the LCD block

For adjusting the video section
For adjusting the color viewfinder

For adjusting the flange back

For adjusting the flange back

J-1

J-2

J-6

J-3

J-7

J-8

J-4

J-5

Fig. 5-1-1.

J-9

J-10

J-11

• Oscilloscope

• Color monitor

• Vectorscope

• Regulated power supply

• Digital voltmeter

Note1: If the micro processor IC in the adjustment remote commander is

not the new micro processor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new micro
processor (8-759-148-35).

5-5

Fig. 5-1-2.

Note1: For details of how remove the cabinet and boards, refer to “2.

DISASSEMBLY”.

Note2: When performing only the adjustments, the lens block and boards

need not be disassembled.

Note3: Before performing the adjustments, check the data of page: 0,

address: 10 is “00”. If not, set data: 00 to this address.

1)

Connect the equipment for adjustments according to Fig. 5-1-3.

2)

The front panel block (SI-032 board (Microphone amp, remote
commander receiver), FP-411 flexible (MIC jack, Headphone
jack, LANC jack, MF photo sensor)) must be assembled for
connecting the adjustment remote commander.

Note4: Only for DCR-TRV240E model, as removing the cabinet (R)

(removing the VC-276 board CN1110) means removing the lithium
3V power supply (CF-2500 block BT001), data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data. If the cabinet (R) has been removed, the self-diagnosis
data, data on history of use (total drum rotation time etc. ) will be
lost. Before removing, note down the self-diagnosis data (data of
page: 2, address: B0 to C6) and data on history use (data of page:
2, address: A5 to AA). (Refer to “5-4. Service Mode” for the self-
diagnosis data and data on the history use.)

Note5: Setting the “Forced Camera Power ON” Mode

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE

button.

The above procedure will enable the camera power to be turned
on with the SS-1380 block removed. After completing adjustments,
be sure to exit the “Forced Camera Power ON Mode”.

Note6: Exiting the “Forced Camera Power ON” Mode

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button.

3) Select page: 0, address: 01, and set data: 00.

Front of the lens

1.5 m

Pattern box

5-6

Fig. 5-1-3.

Color monitor

AUDIO/VIDEO
jack

LANC 
jack

VC-276
board

VIDEO
(Yellow)

Vector scope

Terminated at 75

Ω

DCR-TRV340E

CN1103

CN1551

CN7001

CN1105

CN1501

CN4404

CN3101

CN4403

CN4402

CN
4401

CN1108

CN1109

CN1107

CN4001

CN1106

CN1110

Must be connected when performing
the LCD system adjustments.

Must be connected when 
performing the EVF system 
adjustments.

Lens block

EVF block

Memory stick
slot

Front 
panel 
block

To CF-2500 block

Must be 
connected.

Must be connected.

Need not be connected.

SI-032 board
CN301

Adjustment remote
commander 

AUDIO L
(White)

AUDIO R
(Red)

DC IN 
jack

AC power adaptor 
(8.4Vdc)
AC-L10,
AC-VQ800 etc.

CPC-13 jig
(J-6082-443-A)

Multi CPC jig
(J-6082-311-A)

CN5701

CN5502

CN5702

CN5704

CN5703

CN5705

CN5601

CN5501

To PD-160 board
CN5701

Must be connected when performing
the video or EVF system adjustments.

Must be connected
when performing the 
LCD system adjustments.

PD-160 board

Must be connected.

5-7

Fig. a

(VIDEO terminal

output waveform)

Fig. b (monitor TV picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.

1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.

1.

POWER switch (SS-1380 block) ........................... CAMERA

2.

NIGHT SHOT switch (Lens block) ................................. OFF

3.

DEMO MODE (Menu display) ....................................... OFF

4.

DIGITAL ZOOM (Menu display) ................................... OFF

5.

STEADY SHOT (Menu display) ..................................... OFF

6.

DISPLAY (Menu display) ................................. V-OUT/LCD

7.

DISPLAY (CF-2500 block) .............................................. ON

8.

FOCUS switch (CF-2500 block) .......................... MANUAL

9.

BACK LIGHT (CF-2500 block) ...................................... OFF

10. PROGRAM AE (Menu display) ...................................... OFF
11. PICTURE EFFECT (Menu display) ................................ OFF
12. DIGITAL EFFECT (Menu display) ................................. OFF
13. AUTO SHUTTER (Menu display) .................................. OFF
14. 16 : 9 WIDE (MENU display) ......................................... OFF

2. Order of Adjustments
Basically carry out adjustments in the order given.

Fig.5-1-4.

3. Subjects
1)

Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)

2)

Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)

3)

Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm 

×

841mm) black and white vellum paper.

Fig. 5-1-5.

Note: Use matte vellum paper bigger than A0, and make sure the edges of

the black and white paper joined together are not rough.