DOWNLOAD Sony DCR-TRV238E / DCR-TRV239E (serv.man2) Service Manual ↓ Size: 5.44 MB | Pages: 127 in PDF or view online for FREE

5-43

Mode

Playback

Signal

Recorded signal at “Preparations
before adjustments”

Measurement Point

Pin qh of CN1108 (RF MON) (Note 1)
Ext. trigger: Pin qd of CN1108 (RF
SWP)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

18, 19, 1B, 1C, 21, 2C

Specified Value

The data of page: 3, address: 03 is “00”

Connect a 75

Ω

 resistor between Pin qh and Pin w; (GND) of

CN1108.
75

Ω

 resistor (Parts code: 1-247-804-11)

The  “AGC Center Level Adjustment” must have already been
completed before starting this adjustment.

1

0

01

01

Set the data.

2

C

18

20

Set the data, and press PAUSE
button.

3

C

19

20

Set the data, and press PAUSE
button.

4

C

1B

25

Set the data, and press PAUSE
button.

5

C

1C

25

Set the data, and press PAUSE
button.

6

C

21

CA

Set the data, and press PAUSE
button.

7

C

2C

03

Set the data, and press PAUSE
button.

8

Playback the recorded signal at
“Preparations before adjustments”

9

2

4D

40

Set the data.

10

3

33

08

Set the data.

11

Confirm that the playback RF
signal is stable. (Fig. 5-3-4.)

12

3

01

07

Set the data, and press PAUSE
button.

13

3

02

Check that the data changes from
“07” to “00” in about 20 seconds
after pressing PAUSE button.

14

3

03

Check that the data is “00”.
(Note3)

15

Perform “Processing after
Completing Adjustments”.

If the data is other than “00”, adjustment has errors.

1

0

01

01

Set the data.

2

2

4D

00

Set the data.

3

3

33

00

Set the data.

4

8

21

00

Set the data, and press PAUSE
button.

5

0

01

00

Set the data.

Fig. 5-3-4.

qd

qh

5-44

Mode

VTR stop

Signal

Arbitrary

Measurement Point

Display data of page: 3, address: 02, 03

Measuring Instrument

Adjustment remote commander

Adjustment Page

C

Adjustment Address

1F, 20, 22, 29

Specified Value

Display data of page: 3, address: 02 is
“00”.
Display data of page: 3, address: 03 is
“00”.

The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

3

01

30

Set the data, and press PAUSE
button.

3

3

02

Check that the data changes to
“00” with in 10 sec. (Note2)

4

3

03

Check that the data is “00”.
(Note3)

5

0

01

00

Set the data.

If it isn’t satisfied, there are errors.

If the data of page: 3, address: 03 is other than “00”, there are
errors. For the error contents, see the following table. (For the bit
values, refer to “5-4. SERVICE MODE”,  “4-3. 3. Bit value
discrimination”.)

If deviated in this case causes switching noise or jitter on the Hi8/
Standard8 mode played back screen.

Mode

Playback

Signal

Hi8/Standard8 alignment tape:
  For tracking adjustment (WR5-1CP)

Measurement Point

CH1: Pin 8 of CN1108 (RF SWP)
CH2: Pin 5 of CN1108 (PB RF)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

40, 41

Specified Value

t1 = 0 ± 10 

µ

sec

The data of page: 0, address: 10 must be “00”.

1

Set to the stop mode.

2

0

01

01

Set the data.

3

C

3E

40

Set the data, and press PAUSE
button.

4

2

4D

80

Set the data.

5

Set to the playback mode.

6

C

40

Change the data and minimize
“t1”. (Coarse adjustment)

7

C

40

Press PAUSE button

8

C

41

Change the data and adjust so that
the switching position (t1)
becomes the specified value. (Fine
adjustment)

9

C

41

Press PAUSE button

10

C

3E

00

Set the data, and press PAUSE
button.

11

2

4D

00

Set the data.

12

0

01

00

Set the data.

Fig. 5-3-5.

±

µ

Bit value of page: 3,

Error contents

address: 03

bit 2 = 1 or bit 3 = 1

PLL f

0

 fine adjustment is defective

bit 4 = 1 or bit 5 = 1

PLL f

0

 adjustment is defective

bit 6 = 1

LPF f

0

 adjustment is defective

5-45

Set the Cap FG signal duty cycle to 50% to establish an appropriate
capstan servo. If deviated, the uneven rotation of capstan and noise
can occur in the Hi8/Standard8 LP mode.

Mode

Playback

Signal

Hi8/standard 8 alignment tape :
For checking operation

(WR5-5CSP)

Measurement Point

Pin qg of CN1108 (CAP FG)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

16

Specified value

Duty = 50 ± 1 %

The data of page: 0, address: 10 must be “00”.

1

Set to the playback mode.

2

0

01

01

Set the data.

3

3

01

00

Set the data, and press PAUSE
button.

4

3

01

81

Set the data, and press PAUSE
button.

5

3

02

Check that the data changes from
“81” to “00”.

6

3

03

Check that the data is “00”.
(Note2)

7

Check that Duty of CAP FG signal
satisfies the specified value. If not,
repeat steps 3 to 7.

8

0

01

00

Set the data.

If the data of page: 3, address: 03 is other than “00”, there are
errors. For the error contents, see the following table. (For the bit
values, refer to “5-4. SERVICE MODE”,  “4-3. 3. Bit value
discrimination”.)

Bit value of page: 3,

Error contents

address: 03

bit 0 = 1

Adjustment time-out

bit 1 = 1

Hi8/Standard8 mode wasn’t set up.

Fig. 5-3-6.

×

5-46

Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.

Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.

Mode

Camera

Subject

Not required

Measurement Point

Pin qh of IC1502

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

12

Specified Value

f = 18000000 ± 90Hz

The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

F

12

Change the data and set the
frequency (f) to the specified
value.

3

F

12

Press PAUSE button.

4

0

01

00

Set the data.

Mode

VTR stop

Signal

No signal

Measurement Point

Y signal terminal of S VIDEO jack
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

25

Specified Value

A = 1000 ± 20mV

The data of page: 0, address: 10 must be “00”.

1

0

01

01

Set the data.

2

D

FE

10

Set the data, and press PAUSE
button.

3

3

0C

02

Set the data, and press PAUSE
button.

4

C

25

Change the data and set the Y
signal level (A) to the specified
value.

5

C

25

Press PAUSE button.

6

3

0C

00

Set the data, and press PAUSE
button.

7

D

FE

00

Set the data, and press PAUSE
button.

8

0

01

00

Set the data.

IC1502

25

36

12

24 13

37 48

1

Fig. 5-3-7.