Sony DCR-TRV16E / DCR-TRV18E Service Manual ▷ View online
— 13 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-5.
TOP CABINET ASSEMBLY
3
Screw (M1.7
×
4),
lock ace, p2
2
Screw (M1.7
×
4),
lock ace, p2
4
Claw
5
Top cabinet assembly
1
Slide the EVF
in the direction of the arrow.
2-6.
CABINET (R) SECTION
5
Remove the Cabinet (R) section
in the direction of the arrow.
Because the
7
Cabinet (R) section is connected
to the main unit using the
6
FP-434 flexible board,
the flexible board may be damaged if you remove
the Cabinet (R) section forcibly. Be very careful not
to damage the flexible board.
the Cabinet (R) section forcibly. Be very careful not
to damage the flexible board.
7
Cabinet (R) section
4
Screw
(M1.7
×
4),
lock ace, p2
1
Screw
(M1.7
×
4),
lock ace, p2
2
Screw
(M1.7
×
4),
lock ace, p2
3
Open the
cassette lid
6
FP-434 flexible board
(40P)
Caution
— 14 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-7.
BATTERY PANEL SECTION
A
VA-117
1
Screw
(M1.7
×
4),
lock ace, p2
1
Screw
(M1.7
×
4),
lock ace, p2
2
Strap bracket
(lower)
4
Battery terminal board
3
BT panel assembly
3
Two screws
(M1.7
×
4),
lock ace, p2
6
Battery terminal
board (6P)
5
Remove the BT panel section
in the direction of the arrow
A
.
7
BT panel section
2
CPC lid
4
Open the
cassette lid
2-8.
EVF SECTION
VA-117
VA-117
6
EVF section
5
FP-435 flexible board
(20P)
3
Screw
(M1.7
×
2.5), p
4
Peel off the tape.
1
Slide the EVF slightly
in the direction of the arrow
so that the two screws
so that the two screws
2
become visible.
2
Two tapping screws
(M1.7
×
5)
— 15 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-9.
LB-077 BOARD
8
1
Screw
(M1.7
×
2.5), p
5
Two tapping screws
(M1.7
×
6)
7
VF cabinet (upper)
assembly
qa
VF lens assembly
0
LB-077 board,
Lamp guide
qf
LB-077 board
qd
Lamp guide
9
Three claws
Prism sheet
Illuminator
6
Two claws
2
Claw
4
VF flexible retainer sheet
3
Flexible retainer sheet metal
qs
Two claws
When separating the
0
LB-077 board and
Lamp guide from the
qa
VF lens assembly
by removing the three
9
claws, do not face
the side of the VF lens assembly on which
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp guide
because the three claws located in the VF
lens assembly are easy to break.
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp guide
because the three claws located in the VF
lens assembly are easy to break.
Hold the illuminator
and others using
tape or paper as
shown to prevent
them from falling.
and others using
tape or paper as
shown to prevent
them from falling.
Caution
— 16 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-10. VA-117 BOARD (1)
VA-117
VC-280
5
VA-117 board
1
FP-436 flexible board
(20P)
2
FP-434
flexible board
(12P)
(28P)
3
Four screws
(M1.7
×
2.5), p
4
Board to board
connector (100P)
Click on the first or last page to see other DCR-TRV16E / DCR-TRV18E service manuals if exist.