DOWNLOAD Sony DCR-TRV16E / DCR-TRV18E Service Manual ↓ Size: 1.19 MB | Pages: 32 in PDF or view online for FREE

— 9 —

The following flow chart shows the disassembly procedure.

DCR-TR

V16E/TR

V18E/TR

V116E/TR

V118E

2-1.  LCD section (PD-161 board)

2-2.  EVF section (LB-077 board)

2-3.  Front panel section

2-5.  Top cabinet assembly

(page 11)

(page 12)

(page 13)

2-6.  Cabinet (R) section

(page 13)

2-7.  Battery panel section

(page 14)

2-8.  EVF section

(page 14)

2-10. VA-117 board (1)

(page 16)

2-11. Main chassis complete section (page 17)

2-12. VA-117 board (2)

(page 18)

2-16. JK-217, JK-218 boards

(page 20)

2-14. Lens section

(page 19)

2-17. CK-108 board

(page 21)

2-18. Hinge assembly

(page 22)

2-19. Control switch block (PS-CX2670)

(page 23)

2-20. Memory stick connector
         (TRV18E/TRV118E)

(page 24)

2-13. VC-280 board

(page 18)

(page 10)

(page 12)

2-4.  MA-409, FB-219 boards

(page 15)

2-9.  LB-077 board

(page 19)

2-15. Mechanism deck

— 10 —

NOTE: Follow the disassembly procedure in the numerical order given.

PD-161

B

B

A

A

7

 P cabinet (c) assembly,

     Indication LCD block assembly

P cabinet (c) assembly

5

 

P cabinet (M)

8

 

Liquid crystal 

     indicator module

9

 

Back light

     (Cold cathode fluorescent tube)

1

 

Screw

     (M2 

× 

4), 

     lock ace, p2

6

 

FP-441 flexible board

     (Indication LCD block assembly) 
     (20P)

2

 

Screw

     (M2 

× 

4), 

     lock ace, p2

0

 

PD-161 board, 

     P frame assembly

3

 

Two screws

     (M2 

× 

4), 

     lock ace, p2

4

 

Five claws

FP-441 flexible board

The 

7

 P cabinet (C) assembly is securely 

fixed in the LCD unit by the five 

4

 claws. 

Because the Indication LCD block assembly 
installed in the Cabinet (C) assembly is 
connected to the PD-161 board with the 
FP-441 flexible board, the flexible board 
may be damaged if the Cabinet (C) 
assembly is removed forcibly. 
Be careful not to damage the flexible board.

Indication LCD 
block assembly

— 11 —

B

A

2

 

Two tapping screws

     (M1.7 

× 

6)

4

 VF cabinet (upper) 

     assembly

6

 VF lens assembly

7

 

LB-077 board, 

Lamp guide

q;

 

LB-077 board

9

 Lamp guide

5

 

Three claws

Prism sheet

Illuminator

3

Two claws

8

 Two claws

1

 Raise the EVF in the 

     direction of the arrow 

A

 

     and slide it in the direction 
     of the arrow 

B

.

When separating the 

7

 LB-077 board and 

Lamp guide from the 

6

 VF lens assembly 

by removing the three 

5

 claws, do not face 

the side of the VF lens assembly on which 
the LB-077 board is installed, downwards. 
Because the Illuminator and others may fall 
out of the VF lens assembly, hold the 
illuminator and others using tape or paper 
as shown to prevent them from falling. 
Be careful on this point especially when 
removing the LB-077 board and Lamp guide 
because the three claws located in the VF 
lens assembly are easy to break.

Hold the illuminator 
and others using 
tape or paper as 
shown to prevent 
them from falling.

— 12 —

4

 S

crew

     (M1.7 

× 

4), 

     lock ace, p2

1

 S

crew

     (M1.7 

× 

4), 

     lock ace, p2

5

 Remove the Front panel section 

     in the direction of the arrow 

A

.

A

3

 

Open the 

     jack cover assembly

7

 

Front panel section

2

 S

crew

     (M1.7 

× 

4), 

     lock ace, p2

6

 

FP-437 flexible board

    (24P)

Because the 

7

 Front panel section is connected 

to the main unit by the 

6

 FP-437 flexible board, 

the flexible board may be damaged if you remove 
the Front panel section forcibly. 
Be very careful not to damage the flexible board.

1

 

Microphone (4P)

8

 

MA-409 board

MA-409 board

Route the harness of the Microphone 
underneath the MA-409 board as shown 
in the illustration below. 

4

 

FB-219 board

2

 

Screw

     (M1.7 

× 

2.5), p

5

 Tapping screw 

     (M1.7 

×

 3.5)

3

 Tapping screw 

     (M1.7 

×

 3.5)

7

 

Focus button

    FP-444 flexible board

6

 

Focus button retainer