DOWNLOAD Sony DCR-TRV140 Service Manual ↓ Size: 13.7 MB | Pages: 127 in PDF or view online for FREE

To obtain normal playback waveform output, adjust the switching
position.

Mode

VTR playback

Signal

Digital 8 alignment tape: SW/OL
standard (WR5-2D)

Measurement Point

Displayed data of page: 3, address:
03

Measuring Instrument

Adjusting remote commander

Adjustment Page

C

Adjustment Address

10, 11, 12, 13

Specified value

The data of page: 3, address: 03 is
“00”

Order Page Address Data

Procedure

1

Insert the SW/OL standard
tape and enter the VTR stop
mode.

2

0

01

01

3

3

21

Check the data is “02”.
(Note 1)

4

3

01

0D

Press PAUSE button.

5

3

02

Check the data changes to
“00”.

6

3

03

Check the data is “00”.
(Note 2, 3)

7

3

21

Check the data is not “62”.
(Note 4)

8

C

10

Check the data is not “E7” or
more. (Note 5)

9

0

01

00

If the data is “72”, the tape top being played.
After playing the tape for 1 to 2 seconds, stop it, and
perform step 4 and higher.
If the data is “62”, the tape end being played. After re-
wind the tape, and perform step 4 and higher.

If bit0 of the data is “1”, the A channel is defective.
If bit1 of the data is “1”, the B channel is defective.
Contents of the defect is see written into page: C, ad-
dress: 10 and 12. See following table.
(For the bit values, refer to “5-4. SERVICE MODE”,
“4-3. 3. Bit value discrimination”.)
If bit3 of the data is “1”, the tape end being played. After
rewind the tape, and repeat steps 3 to 6.

If bit0 or bit1 of the data is “1”, only once, select page:
C, address 21, set data: 10, press the PAUSE button, and
repeat steps 3 to 6.

If the data is “62”, after rewind the tape, and repeat steps
1 to 7.

If the data is “E7” or more, adjustment has errors, and
repeat steps 1 to 8.

Data of page: C,

Contents of defect

address: 10

EE

Writing into EEPROM (IC4502) is
defective

E8

Adjustment data is out of range

E7

No data is returned from IC3301
 (CAIN)

Data of page: C,

Contents of defect

address: 12

E8

Adjustment data is out of range

E7

No data is returned from IC3301
 (CAIN)

Mode

CAMERA record and VTR playback

Subject

Arbitrary

Measurement Point

CH1: PB RF (MON) (Pin 9 of
CN1011) (Note 1)
CH2 (Trigger): SWP (Pin 5 of
CN1011)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

1E

Specified value

The data of page: 3, address: 03 is
“00”

Connect a 75 

Ω

 resistor between PB RF (MON) and GND

of CPC-jig.

Use a Hi8 MP tape.

Order Page Address Data

Procedure

1

0

01

01

2

8

2A

C8

Press PAUSE button.

3

Record camera signal for 1
minute, and rewind the tape.

4

2

2E

01

5

3

33

08

6

Playback the recorded
segment at step 3.

7

Confirm that the playback
RF signal is stable.

8

3

01

23

Press PAUSE button.

9

3

02

Check the data changes to
“00”

10

3

03

Check the data is “00”.
(Note 3)

11

3

33

00

12

2

2E

00

13

8

2A

00

Press PAUSE button.

14

0

01

00

 If the data is other than “00”, adjustment has errors.

13.3 msec

PB RF signal is stable

SWP

PB RF
(MON)

Mode

CAMERA record and VTR playback

Subject

Arbitrary

Measurement Point

CH1: PB RF (MON) (Pin 9 of
CN1011) (Note 1)
CH2 (Trigger): SWP (Pin 5 of
CN1011)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

18, 19, 1B, 1C, 21, 2C

Specified value

The data of page: 3, address: 03 is
“00”

Connect a 75 

Ω

  resistor between PB RF (MON) and

GND of CPC-jig.

Use a Hi8 MP tape.

Order Page Address Data

Procedure

1

0

01

01

2

8

2A

C8

Press PAUSE button.

3

Record camera signal for 1
minute, and rewind the tape.

4

C

18

20

Press PAUSE button.

5

C

19

20

Press PAUSE button.

6

C

1B

25

Press PAUSE button.

7

C

1C

25

Press PAUSE button.

8

C

21

CA

Press PAUSE button.

9

C

2C

03

Press PAUSE button.

10

2

2E

01

11

3

33

08

12

Playback the recorded
segment at step 3.

13

Confirm that the playback
RF signal is stable.

14

3

01

07

Press PAUSE button.

15

3

02

Check the data changes to
“00”

16

3

03

Check the data is “00”.
(Note 3)

17

3

33

00

18

2

2E

00

19

8

2A

00

Press PAUSE button.

20

0

01

00

 If the data is other than “00”, adjustment has errors.

13.3 msec

PB RF signal is stable

SWP

PB RF
(MON)

Mode

VTR stop

Signal

Arbitrary

Measurement Point

Displayed data of page: 3, address:
02 and 03

Measuring Instrument

Adjusting remote commander

Adjustment Page

C

Adjustment Address

1F, 20, 22, 29

Specified value

The data of page: 3, address: 02 is “00”
The data of page: 3, address: 03 is “00”

Order Page Address Data

Procedure

1

0

01

01

2

3

01

30

Press PAUSE button.

3

3

02

Check the data changes to
“00” within 10 seconds.
(Note 1)

4

3

03

Check the data is “00”.
(Note 2)

5

0

01

00

If the data is not changes to “00” within 10 seconds,
adjustment has errors.

If the data is other value, adjustment has errors.
For the error contents, see the following table.
(For the bit values, refer to “5-4. SERVICE MODE”,
“4-3. 3. Bit value discrimination”.)

Bit value of page: 3,

Error contents

address: 03 data

bit 6 = 1

LPF f

0

 adjustment is defective

bit 2 = 1 or bit 3 = 1

PLL f

0

, fine adjustment is defective

bit 4 = 1 or bit 5 = 1

PLL f

0

, adjustment is defective