DOWNLOAD Sony DCR-TRV140 / DCR-TRV140E / DCR-TRV140M (serv.man2) Service Manual ↓ Size: 589.92 KB | Pages: 10 in PDF or view online for FREE

J-9

J-10

J-11

J-12

I/F unit for LANC control

Mini pattern box

Camera table

CPC jig connector

J-6082-521-A

J-6082-353-B

J-6082-384-A

J-6082-539-A

For connecting the adjustment remote commander

For adjusting the flange back

For adjusting the flange back

For connecting the adjustment remote commander

If the micro processor IC in the adjustment remote com-
mander is not the new micro processor (UPD7503G-C56-
12), the pages cannot be switched. In this case, replace
with the new micro processor (8-759-148-35).

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

J-10

J-11

J-12

Ref. No.

Name

Parts Code

Usage

• Oscilloscope

• Color monitor

• Vectorscope

• Regulated power supply

• Digital voltmeter

• Frequency counter

5-4

-

&

5-5

For details of how remove the cabinet and boards, refer
to “2. DISASSEMBLY”.

When performing only the adjustments, the lens block
and boards need not be disassembled.

1) Connect the equipment for adjustments according to Fig. 5-1-

4.

2) Connect the adjustment remote commander to VC-273 board

CN1011 via I/F unit for LANC control (J-6082-521-A) and
CPC jig connector (J-6082-539-A). (Fig. 5-1-3)
To operate the adjustment remote commander, connect the AC
power adaptor to the DC IN jack of I/F unit for LANC control,
or connect the L series Info-LITHIUM battery to the battery
terminal of I/F unit for LANC control.

3) The front panel block (SI-033 board,  video light, microphone

unit) need not be assembled except during the steadyshot op-
eration check.

\

)

[

)

[

[

=

5-6

-

&

 Use either the AC power adaptor or the InfoLITHIUM battery as the power supply of I/F unit for LANC control.

Adjustment
remote commander

AC power adaptor

L series
InfoLITHIUM
battery
(7.2 Vdc)

LANC
jack

I/F unit for LANC control (Note)

(J-6082-521-A)

CPC jig connector

(J-6082-539-A)

EVF BLOCK

Must be connected when 
performing the electronic 
viewfinder system adjustment.

Must be connected

DC IN jack

Video
(yellow)

Color monitor

Vector scope

CN1551

CN1005

CN1007

CN4404

CN4403

CN4402

FRONT PANEL BLOCK

LENS BLOCK

CD-353 BOARD

CN2001

To PD-156 
board

CN5701

PD-156  BOARD

CABINET (R)

SI-033 BOARD

CN752

CN4401

CN5501

CN5502

CN5704

CN5703

CN5601

A/V OUT jack

CN3101

VC-273 BOARD

Must be connected

Must be connected when 
performing the LCD system
adjustment.

Must be connected when 
performing the steadyshot 
check.

AC power adaptor

To CONTROL SWITCH 
BLOCK (CF-2000)

CN1003

CN5701

CN5702

CN1002

CN1501

CN1011

CN701

CN1009

Terminated
75 

Ω

Audio L (white)

Audio R (red)

Multi CPC jig
(J-6082-311-A)

Must be connected when performing
the LCD system adjustment.

]

\

)

5-24

-

5-30

When replacing the LCD unit, be careful to prevent dam-
ages caused by static electricity.

Set the VF B.L. (Menu setting) to the BRT NORMAL

Most of the measuring points for adjusting the viewfinder system
are concentrated at VC-273 board CN1011. Connect the measur-
ing instruments via I/F unit for LANC control (J-6082-521-A) and
CPC jig connector (J-6082-539-A). The following table lists the
test point of I/F unit for LANC control.

Pin No.

Signal Name

Pin No.

Signal Name

N.C

BL

15

EVF VCO

14

EVF VG

N.C

BL 4.75

9

PB RF (MON)

3 (N.C)

BPF MONI

6, 8, 10,

GND

N.C

TMS

7 (N.C)

REC RF (RF IN)

N.C

TDI

N.C

TDO

5

SWP

N.C

TCK

4 (N.C)

CAP FG

2 (N.C)

IR VIDEO

 Pin No. are those of CN1011 on VC-273 board.

Mechanism Section adjustments, checks, and replacement of
mechanism parts, refer to the separate volume “8mm Video Me-
chanical Adjustment Manual IX   M2000 Mechanism  ”.

Connect the adjustment remote commander to CN1011 of VC-
273 board via I/F unit for LANC control (J-6082-521-A) and CPC
jig connector (J-6082-539-A). To operate the adjustment remote
commander, connect the AC power adapter (8.4Vdc) to the DC IN
jack of I/F unit for LANC control, or connect the L series Info-

LITHIUM battery to the battery terminal of I/F unit for LANC
control.

1)

Connect the adjustment remote commander.

2) Turn the HOLD switch of the adjustment remote commander

to the ON position.

3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, and set data: 0C, and press the

PAUSE button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)

 The function buttons becomes inoperable.

5) To quit the record mode, select page: 3, address: 01, set data:

00, and press the PAUSE button of the adjustment remote com-
mander. (Whenever you want to quit the record mode, be sure
to quit following this procedure.)

[

=

[

[

[

5-31

-

&

5-34

1) Clean the tape path face (tape guide, drum, capstan shaft, pinch

roller).

2) Connect the adjustment remote commander.
3) Turn on the HOLD switch of the adjustment remote com-

mander.

4) Select page: 3, address: 33, and set data: 08.
5) Connect the oscilloscope to I/F unit for LANC control.

Channel 1: PB RF (MON)
Channel 2: SWP

Connect a 75 

Ω

 resistor between the test point PB

RF (MON) and GND.
75 

Ω

 resistor (Parts code: 1-247-804-11)

6) Playback the SW/OL standard tape. (WR5-2D)
7) Check that the oscilloscope RF waveform is flat at the entrance

and exit.
If not flat, perform the following section 2-4-2. until it is flat.

8) Perform  “Processing after operations”, after completing ad-

justment.

Pin No.

Signal Name

Pin No.

Signal Name

N.C

BL

15

EVF VCO

14

EVF VG

N.C

BL 4.75

9

PB RF (MON)

3 (N.C)

BPF MONI

6, 8, 10,

GND

N.C

TMS

7 (N.C)

REC RF (RF IN)

N.C

TDI

N.C

TDO

5

SWP

N.C

TCK

4 (N.C)

CAP FG

2 (N.C)

IR VIDEO

 Pin No. are those of CN1011 on VC-273 board.

1) TV monitor
2) Oscilloscope (dual-phenomenon, band width above 30 MHz

with delay mode) (Unless specified otherwise, use a 10 : 1
probe)

3) Frequency counter
4) Digital voltmeter
5) Audio level meter
6) Regulated power supply
7) Digital8 alignment tapes

• SW/OL standard (WR5-2D)

Parts code: 8-967-993-22

• Audio operation check for NTSC (WR5-3ND)

Parts code: 8-967-993-32

• System operation check for NTSC (WR5-5ND)

Parts code: 8-967-993-42

• Audio operation check for PAL (WR5-3CD)

Parts code: 8-967-993-37

• System operation check for PAL (WR5-5CD)

Parts code: 8-967-993-47

8) Adjustment remote commander (J-6082-053-B)
9) CPC jig connector (J-6082-539-A)
10) I/F unit for LANC control (J-6082-521-A)

+

-

[

\