Sony DCR-TRV10 / DCR-TRV10E / DCR-TRV8 / DCR-TRV8E (serv.man2) Service Manual ▷ View online
1-37E
2-1
DCR-TRV8/TRV8E/TRV10/TRV10E
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
The following flow chart shows the disassembly procedure.
DCR-TRV8/8E/10/10E
2-1. LCD panel (PD-110 board, invertor trans unit)
2-2. Front panel assembly
2-3. Cabinet (L), BT panel assembly
2-11. CK-84 board, Speaker
2-12. LCD, Control swith block
2-4.EVF
2-5.LB-60 board
2-6. DD-123 board, VC-217 board
2-7. Mechanism deck
2-8. CS flame assembly
2-9.Lens, Outer connector (hot shoe), JK-170 board
2-10.MS shassis, Control switch block (PS-4550)
2-1. LCD PANEL (PD-110 BOARD, INVERTOR TRANS UNIT)
1
Two screws (M1.7) lock ace
2
Two screws
(M1.7) lock ace
3
P cabinet (M) assembly
(Remove the four claws
A
and
B
.)
5
FP-90 flexible board
CN8613 6P (PD-110 board)
!•
FP-90 flexible board
!¶
Tapping screw
(M1.7
×
3.5)
!™
Screw
(M1.7
×
2.5)
!£
PD-110 board
(Remove the two claws
D
and
E
.)
8
Indication LCD block
assembly (LCD901)
9
Cold cathode
fluorescent tube
(ND901)
(ND901)
!§
Inverter transformer unit
!¢
Connector
(CN5803)
!∞
Connector
(CN5802)
!º
Connector (CN5900)
!¡
Crystal indication
module (LCD902)
(Remove the LCD after
releasing the claw from
the
(Remove the LCD after
releasing the claw from
the
C
area.)
6
Flexible board (LCD901)
CN5601 24P (PD-110 board)
7
Flexible board (ND901)
CN5601 24P (PD-110 board)
4
P cabinet (C) assembly
C
Claws
B
Claws
D
Claws
E
Claws
A
2-2
2-2. FRONT PANEL ASSEMBLY
1
Screw (M1.7) lock ace
3
Screw (M1.7) lock ace
9
Tapping screw (M1.7
×
3.5)
!£
Connector
CN7300 4P (MA-358 board)
!™
MA-358 board
!¡
Tapping screw (M1.7
×
3.5)
!¢
Two tapping screws
(M1.7
×
3.5)
!∞
Microphone retainer
assembly
!§
Microphone unit
7
F panel assembly
4
Screw (M1.7) lock ace
6
Screw (M1.7) lock ace
8
JK-170 board
CN7306 26P (MA-358 board)
!º
SE-94board
CN7307 5P
(MA-358 board)
(MA-358 board)
2
Top cabinet assembly
5
Open the jack cover.
2-3. CABINET (L), BT PANEL ASSEMBLY
1
Screw (M1.7) lock ace
3
Screw (M1.7) lock ace
8
Three screws
(M1.7) lock ace
9
BT panel assembly
!º
Connector
CN8610 3P
(DD-123 board)
(DD-123 board)
5
Screw (M1.7) lock ace
6
Cabinet (R) assembly
7
FP-82 flexibli board
CN8608 60P (CK-84 board)
4
Push the knob in the direction of the
arrow
A
, and open the grip cabinet
in the direction of the arrow
B
.
2
Two screws (M1.7) lock ace
Knob
Grip cabinet
A
B
2-3
2-4. EVF
2
Two screws
(M1.7
×
6) B tight
1
Screw
(M1.7
×
2.5)
3
FP-87 flexible board
CN5101 27P (DD-123 board)
4
Flexible retainer sheet
5
Two tapping screws
(M1.7
×
6)
9
EVF assembly
(Remove the assembly
while holding it upward.)
while holding it upward.)
8
Tilt down the EVF.
6
Tilt up the EVF.
7
Screw (M1.7) lock ace
2-5. LB-60 BOARD
1
Two tapping screws
(M1.7
×
6)
3
VF lens assembly
6
Two claws
4
FP-87 flexible board
CN5201 27P (LB-60 board)
5
Flexible board (LCD)
CN5202 16P (LB-60 board)
7
LCD cushion (455)
!™
LB-60 board
9
LCD cushion (455)
!¡
LCD cushion (1)
!º
LCD
8
BL illuminator (455)
2
VF cabinet (upper) assembly
Note when installing the LB-60 board
The portion that is shown by the illustration, can be easily
caught during reassembling.
Be careful not to damage or break the portion shown.
The portion that is shown by the illustration, can be easily
caught during reassembling.
Be careful not to damage or break the portion shown.
Click on the first or last page to see other DCR-TRV10 / DCR-TRV10E / DCR-TRV8 / DCR-TRV8E (serv.man2) service manuals if exist.