DOWNLOAD Sony DCR-PC8E (serv.man2) Service Manual ↓ Size: 4.69 MB | Pages: 119 in PDF or view online for FREE

2-9

VC-265D

Adjustment remote
commander (RM-95)

Control switch block
(PS-1770) (8P)

Control switch block (FK-1770)
(A-7096-840-A) (51P)

When exiting the “Forced Camera Power ON” mode,
connect the control switch block (PS-1770) to the 
control switch block (FK-1770).

Lens-EVF section

VC-265D board

CF-085 board (88P)

Mechanism deck

AC IN

AC power 
adaptor

DC-IN connector

To check the camera section, set the camera to the “Forced camera power ON” mode. (Or, connect the control switch block 
(PS-1770) to the control switch block (FK-1770) and set the power switch to the “CAMERA” position.)
Operate the camera functions of the zoom and focus using the adjustment remote commander (with the HOLD switch set in 
the OFF position).

Note  : The control switch block (FK-1770) is used for the repair parts as a jig.

1)  Select page: O, address: 01, and set data: 01.
2)  Select page: D, address: 10, set data: 01 and 

press the PAUSE button of the adjustment remote
commander.

1) Select page: O, address: 01, and set data: 01.
2) Select page: D, address: 10, data: 00, and press the PAUSE 

button of the adjustment remote commander.

3) Select page : 0, address: 01, and set data: 00.

BJ-002A board

2-10

(Remove the LCD unit referring to section 2-1 before starting disassembling)

1

 Screw

     (M1.7 

×

 2.5)

4

 Screw (M1.7 

×

 2.5)

2

 Tapping 

     screw
     (M1.7 

×

 5)

9

3

 Blind plate assembly,

     PO-007 board

5

 Two claws

7

 Claw

6

 Hinge cover (rear)

8

 Hinge cover (front)

2

 PD-113 harness

4

 LCD hinge assembly

1

 PR-063 harness

Harness
(black)

Harness
(black)

Harness
(black)

Harness
(black)

Harness
(gray)

Harness
(gray)

Harness
(gray)

Boss hole

1

 Connect the black harness at the leftmost end of the 

     harness (PR-063) and connect the second gray harness 
     (PR-063) to the PR-037 board by soldering.

2

 Check that there is no cold soldering, non-soldering, 

     solder slump nor solder bridge.

Note: Align the direction of the harness 

A

 as shown in the 

         picture.
         Be careful that the harness must not be caught by the 
         boss hole.

3

 Connect the third black harness and the fourth gray harness 

     from the leftmost end of the PO-007 board by soldering.

4

 Check that there is no cold soldering, non-soldering, solder 

     slump nor solder bridge.

Note: Align the direction of the harness 

A

 as shown in the 

          picture.
          Be careful that the harness must not be caught by the 
          boss hole.

Specification
Reference of counting the harness starts counting from the 
black harness in the end.

Boss hole

Harness
(gray)

7

 PR-063 harness

A

 PR-063 harness

3

 PR-037 board

PR-037 board

PR-037 board

1

 Two solderings

5

 Two solderings

6

 PO-007 board

PO-007 board

Soldering position

PO-007 board

2

 PR-037 board

4

 Blind plate

     assembly

3

 Two claws

2-11

PD-148A

PR-037 

INVERTER
TRANSFORMER UNIT

PO-007

MF-325

BJ-002A

CF-085

VC-265D

NS-013

JACK, BATTERY
CCD IMAGER, PITCH/YAW SENSOR
MF SENSOR
REMOTE COMMANDER RECEIVER
LCD DRIVE, BACK LIGHT
PANEL OPEN
PANEL REVERSE

CAMERA PROCESS, DV PROCESS, VIDEO, AUDIO, SERVO, HI/MECHA CONTROL, 
DC/DC CONVERTER

BJ-002A
CF-085
MF-325
NS-013
PD-148A
PO-007
PR-037

VC-265D

2-12E

The flexible boards contained in the mechanism deck and that in the lens device are not shown.

CONTROL SWITCH BLOCK
(FK-1770)

CONTROL SWITCH BLOCK
(PS-1770)