Sony DCR-PC106E / DCR-PC107E (serv.man4) Service Manual ▷ View online
6-51
DCR-PC106E/PC107E
Display on the
adjustment
remote
commander
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
c
)
D (
d
)
E (
E
)
F (
F
)
Bit values
bit3
or
bit7
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2
or
bit6
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1
or
bit5
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0
or
bit4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
B
Example: If “8E” is displayed on the adjustment remote commander, the
bit values for bit7 to bit4 are shown in the A column, and the
bit values for bit3 to bit0 are shown in the B column.
bit values for bit3 to bit0 are shown in the B column.
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
4. Bit value discrimination
Bit values must be discriminated using the display data of the
adjustment remote commander for following items. Use the table
below to discriminate if the bit value is “1” or “0”.
Bit values must be discriminated using the display data of the
adjustment remote commander for following items. Use the table
below to discriminate if the bit value is “1” or “0”.
A
5. Switch check (1)
Page 2
Address 81
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 2, address: 81.
2)
By discriminating the bit value of display data, the state of the switch can be discriminated.
6. Switch check (2)
Page 7
Address 08
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 7, address: 08.
2)
By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit
0
1
2
3
4
Function
POWER SW (XPOWER SW) (SS6800 block)
MODE SW (XMODE SW) (SS6800 block)
DISPLAY/BATTERY INFO SW (XBATT INFO SW)
(CR-047 board S802)
(CR-047 board S802)
EJECT SW (XEJECT SW) (SS6800 block S001)
CC DOWN SW (Mechanism chassis)
When bit value=1
ON
ON
ON
ON
ON(DOWN)
When bit value=0
OFF
OFF
OFF
OFF
OFF (UP)
Bit
0
Function
Lens shutter (FP-840 flexible S101)
When bit value=1
Close
When bit value=0
Open
7. Switch check (3)
Page 7
Address 0C
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 7, address: 0C.
2)
By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit
1
2
3
Function
MIC jack (SE-401 board J401)
A/V jack (FP-843 flexible J002)
S VIDEO jack (Handycam station)
When bit value=1
Used
Used
Used
When bit value=0
Not used
Not used
Not used
6-52
DCR-PC106E/PC107E
8. Switch check (4)
Page 7
Address 53
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 7, address: 53.
2)
By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit
5
6
Function
A/V jack (Handycam station)
Handycam station connector (CR-047 board CN801)
When bit value=1
Used
Not used
10. Switch check (6)
Page 2
Address 60 to 64
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 2, address: 60 to 64.
2)
By discriminating the display data, the pressed key can be discriminated.
Address
60
(KEY AD0)
(IC8002 tl)
61
(KEY AD1)
(IC8002 y;)
62
(KEY AD2)
(IC8002 ya)
63
(KEY AD3)
(IC8002 yg)
64
(KEY AD4)
(IC8002 yh)
65
(KEY AD5)
(IC8002 yj)
00
(00 to 0C)
START/STOP
(SS6800 block)
(S002)
START/STOP
(SB6300 block)
(S001)
PHOTO
(PHOTO REC)
(ZM6800 block)
(S002)
EASY
(CR-047 board)
(S801)
PANEL REVERSE
(FP-926 flexible)
(S101)
BACK LIGHT
(SS6800 block)
(S003)
19
(0D to 24)
PANEL CLOSE
(FP-847 flexible)
(S001)
32
(25 to 3F)
LCD BACK LIGHT
ON/OFF
(SB6300 block)
(S002)
C1
(AB to D7)
EB
(D8 to FF)
No key input
No key input
No key input
PANEL OPEN
(FP-847 flexible)
(S001)
PANEL NORMAL
(FP-926 flexible)
(S101)
4E
(40 to 5D)
PHOTO
(PHOTO FREEZE)
(ZM6800 block)
(S001)
When bit value=0
Not used
Used
Data
9. Switch check (5)
Page 7
Address 5C
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 7, address: 5C.
2)
By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit
3
Function
REC PROOF SW (Mechanism chassis)
When bit value=1
SAVE
When bit value=0
REC
6-53
DCR-PC106E/PC107E
11. LED check
Page 7
Address 05
Note: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
Select page: 7, address: 05, and set data: 20.
2)
Check that the following LEDs are lit.
TALLY, CHARGE, CAMERA, PLAY/EDIT, NIGHT SHOT light, EASY OPERATION
3)
Select page: 7, address: 05, and set data: 00.
12. Record of Use check (1)
Page 7
Address A7 to A9
Note1: When replacing the drum assembly or the mechanism deck, initialize the data of address: A7 to A9.
Note2: This data will be kept even if the lithium battery (MS-201 board BT501) is removed.
Note3: The data of page: 0, address: 10 must be “00”.
Note2: This data will be kept even if the lithium battery (MS-201 board BT501) is removed.
Note3: The data of page: 0, address: 10 must be “00”.
Address
A7
A8
A9
Function
Drum rotation
Hour (H)
counted time
Hour (M)
(BCD code)
Hour (L)
Remarks
100000th place digit and 10000th place digit of counted time
1000th place digit and 100th place digit of counted time
10th place digit and 1st place digit of counted time
Using method:
1)
1)
The record of use data is displayed at addresses: A7 to A9.
Initializing method:
1)
1)
Select page: 7, address: 00, and set data: 71.
2)
Select page: 7, address: 01, set data: 71 and press the PAUSE button.
3)
Check that the data of page: 7, address: 02 is “01”.
13. Record of Use check (2)
Page 7
Address C8 to CD
Note1: This data will be kept even if the lithium battery (MS-201 board BT501) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Note2: The data of page: 0, address: 10 must be “00”.
Using method:
1)
1)
The record of use data is displayed at addresses: C8 to CD.
Address
C8
C9
CA
CB
CC
CD
Function
User initial power
Year
on date
Month
(BCD code)
Day
Final condensation
Year
occurrence data
Month
(BCD code)
Day
Remarks
After setting the clock, set the date of power on next
6-54
DCR-PC106E/PC107E
14. Record of Self-diagnosis check
Page 7
Address B0 to C6
Note1: This data will be kept even if the lithium battery (MS-201 board
BT501) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Address
Self-diagnosis code
B0
“Repaired by” code (Occurred 1st time) *1
B1
“Block function” code (Occurred 1st time)
B2
“Detailed” code (Occurred 1st time)
B4
“Repaired by” code (Occurred 2nd time) *1
B5
“Block function” code (Occurred 2nd time)
B6
“Detailed” code (Occurred 2nd time)
B8
“Repaired by” code (Occurred 3rd time) *1
B9
“Block function” code (Occurred 3rd time)
BA
“Detailed” code (Occurred 3rd time)
BC
“Repaired by” code (Occurred 4th time) *1
BD
“Block function” code (Occurred 4th time)
BE
“Detailed” code (Occurred 4th time)
C0
“Repaired by” code (Occurred 5th time) *1
C1
“Block function” code (Occurred 5th time)
C2
“Detailed” code (Occurred 5th time)
C4
“Repaired by” code (Occurred the last time) *1
C5
“Block function” code (Occurred the last time)
C6
“Detailed” code (Occurred the last time)
*1: “01”
t “C”, “03” t “E”
Using method:
1)
1)
The past self-diagnosis codes are displayed at addresses: BC to C6. Refer to the following table.
Click on the first or last page to see other DCR-PC106E / DCR-PC107E (serv.man4) service manuals if exist.