Sony DCR-IP45 / DCR-IP45E / DCR-IP55 / DCR-IP55E (serv.man2) Service Manual ▷ View online
2-15
DCR-IP45/IP45E/IP55/IP55E
2-18.CONTROL SWITCH BLOCK (PS-2960)
1
Two tapping s
crews
(M1.7
×
4)
3
Tapping s
crew
(M1.7
×
4)
2
Speaker bracket
7
Speaker
cushion
4
Earth plate
9
Speaker (1.6CM)
0
Control switch block
(PS-2960)
6
Cabinet (rear) assembly
5
Tapping s
crew
(M1.7
×
4)
8
Soldering the
two points
2-19.BT-003 BOARD (IP55/IP55E)
When removing the Bluetooth harness
from the BT-003 board, be sure
to hold the connector of the
Bluetooth harness and remove it.
from the BT-003 board, be sure
to hold the connector of the
Bluetooth harness and remove it.
Caution
2
Two screws
(M1.4
×
2),
lock ace, p2
1
FP-522 flexible board (15P)
4
BT-003 board
3
Bluetooth harness (1P)
Bluetooth
harness
harness
BT-003 board
2-16
DCR-IP45/IP45E/IP55/IP55E
2-20.HINGE ASSEMBLY
4
Screw
(M1.7
×
2.5),
0-no.+p2
1
VF absorbing sheet
3
Two screws
(M1.7
×
4),
lock ace, p2
7
Two screws
(M1.7
×
4),
lock ace, p2
2
Two screws
(M1.7
×
4),
lock ace, p2
6
Three screws
(M1.7
×
2.5),
lock ace, p2
5
FP-523 flexible board (6P)
7
FP-523 flexible board
3
Hinge cover (front)
2
Two claws
5
claw
1
Turn the
operation part of
a hinge assembly
in the direction of the arrow.
1
Turn the
operation part of
a hinge assembly
in the direction of the arrow.
3
Hinge
assembly
2
Harness (PB-051)
6
Hinge cover (lower)
8
FP-524 flexible board (6P)
4
Blind plate assembly
Caution
This screw (
M1.7
×
2.5
) is MEC-processed.
If the screws are removed once, it cannot be re-used.
When re-assembling, use the new MEC screw.
When re-assembling, use the new MEC screw.
2-17
DCR-IP45/IP45E/IP55/IP55E
2-21.FLASH UNIT (ST-2960)
4
Two tapping s
crews
(M1.7
×
4)
3
Remove the ST upper cabinet
in the direction of the arrow.
1
Lift up
stroboscope
block assembly
4
ST lower cabinet
2
S
crew
(M1.7
×
2.5),
lock ace, p2
2
S
crew
(M1.7
×
2.5),
lock ace, p2
1
Two claws
2
Two claws
3
Lens frame
4
Tapping s
crews
(M1.7
×
4)
6
Solenoid
holder
7
ST frame assembly,
Microphone unit
8
Flash unit (ST-2960)
1
Capacitor holder
3
S
crew
(M1.7
×
2.5),
lock ace, p2
5
Claw
2-18
DCR-IP45/IP45E/IP55/IP55E
2-22.COMPRESSION SPRING
(CABINET (L) OPERATION PART OF A HINGE ASSEMBLY)
2
Four tapping s
crews
(M1.7
×
4)
1
Two s
crews
(M2
×
4)
2
Harness cover
3
Lock disk
6
Slider ring
7
G cabinet
8
Click plate
4
G lock claw
5
Compression spring
9
G click spring
3
Harness (BT-053)
(3P)
4
Battery panel assembly
FP-526 flexible board
Battery terminal board
Battery terminal board
Caution
1
Turn the grip in the
direction of the arrow.
This screw
(M2
×
4)
is MEC-processed.
If the screws are removed once, it cannot be re-used.
When re-assembling, use the new MEC screw.
When re-assembling, use the new MEC screw.
The grip can be locked in the three angles of a, b and c.
When rotating the grip do not rotate it higher than the angle (A).
Doing so may damage the rotating block of the grip.
When rotating the grip do not rotate it higher than the angle (A).
Doing so may damage the rotating block of the grip.
Caution
A
NG
a
b
c
Click on the first or last page to see other DCR-IP45 / DCR-IP45E / DCR-IP55 / DCR-IP55E (serv.man2) service manuals if exist.