Sony DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man4) Service Manual ▷ View online
6-24
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_ADJ
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
9D
00
3
0
01
00
NTSC model
PAL model
Fig. 6-1-15
9.
Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Video terminal of A/V OUT jack (75
Ω terminated)
Ω terminated)
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
33, 35, 3A, 3B
Specified Value
All color luminance points should
settle within each color reproduction
frame.
settle within each color reproduction
frame.
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Perform “Flange Back Adjustment” and “F No. Standard
Note 2: Perform “Flange Back Adjustment” and “F No. Standard
Data Input” before this adjustment.
Note 3: NTSC model: DCR-HC52/HC54
PAL model: DCR-HC51E/HC52E/HC53E/HC54E
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame) ”
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame) ”
2
0
01
01
3
6
9D
83
4
6
01
3D
Press PAUSE (Write) button.
5
F
80
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
77: NTSC model
F7: PAL model
F7: PAL model
6
Adjust the GAIN and PHASE
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
7
F
Change the data and settle each
color luminance point in each
color reproduction frame.
(Note 4)
color luminance point in each
color reproduction frame.
(Note 4)
Note 4: Be sure to press the PAUSE (Write) button of the adjust-
ing remote commander before changing the addresses.
If not, the new data will not be written to the memory.
If not, the new data will not be written to the memory.
R-Y
B-Y
R
G
B
M
G
C
Y
Y
E
Burst
position
position
R-Y
B-Y
R
G
B
M
G
C
Y
Y
E
Burst
position
position
33
35
35
3A
3B
3B
6-25
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_ADJ
10. Auto White Balance Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the white balance reference at 3200K.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
2A to 2D, 60 to 63, 1A, 1B
Note 1: Perform “Color Reproduction Adjustment” before this
adjustment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
6
02
Check the data is “00”.
(Note 3)
(Note 3)
4
Wait for 2 seconds.
5
6
01
B5
Press PAUSE (Write) button.
(Note 4)
(Note 4)
6
6
02
Check the data changes to
“01”.
“01”.
Note 3: If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Note 4: The adjustment data will be automatically input to page:
F, address: 2A to 2D, 60 to 63, 1A, 1B.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
6-26
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_ADJ
11. Auto White Balance Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility
will be poor.
If it is not correct, auto white balance and color reproducibility
will be poor.
Subject
Clear chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Filter
Filter C14 for color temperature
correction
correction
Adjustment Page
F
Adjustment Address
2E to 31, 3E to 41, 64 to 67
Note 1: Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: NTSC model: DCR-HC52/HC54
Note 3: NTSC model: DCR-HC52/HC54
PAL model: DCR-HC51E/HC52E/HC53E/HC54E
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
6
02
Check the data is “00”.
(Note 4)
(Note 4)
4
F
3E
2B
Press PAUSE (Write) button.
5
F
3F
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
1E: NTSC model
6E: PAL model
6E: PAL model
6
F
40
5C
Press PAUSE (Write) button.
7
F
41
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
D8: NTSC model
B8: PAL model
B8: PAL model
8
Place the C14 filter on the
lens.
lens.
9
6
01
47
Press PAUSE (Write) button.
10
6
01
45
Press PAUSE (Write) button.
(Note 5)
(Note 5)
11
6
02
Check the data changes to
“01”.
“01”.
Note 4: If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Note 5: The adjustment data will be automatically input to page:
F, address: 2E to 31, 64 to 67.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
3
Remove the C14 filter on the
lens.
lens.
6-27
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_ADJ
Fig. 6-1-16 (A)
Fig. 6-1-16 (B)
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
03
00
3
Remove the ND filter 1.5
(1.0 + 0.4 + 0.1) on the lens.
(1.0 + 0.4 + 0.1) on the lens.
R-Y
B-Y
3 mm
X mm
NTSC model (Burst: 35%)
X = 6.0, Y = 9.0
PAL model (Burst: 37.5%)
X = 7.0, Y = 9.0
Y mm
3 mm
R-Y
2 mm
B-Y
2 mm
12. Auto White Balance Check
RadarW
RadarW
RadarW
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
ND filter 1.0, 0.4 and 0.1
Measurement Point
Video terminal of
Displayed data of
A/V OUT jack
page: 1 (Note 3)
(75
Ω terminated)
Measuring Instrument
Vectorscope
Specified Value
Fig. 6-1-16 (A) and (B)
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Perform “Auto White Balance Adjustment” before this
Note 2: Perform “Auto White Balance Adjustment” before this
adjustment.
Note 3: NTSC model: DCR-HC52/HC54
PAL model: DCR-HC51E/HC52E/HC53E/HC54E
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
Check that the lens is not
covered with either filter.
covered with either filter.
3
6
02
Check the data is “00”.
(Note 4)
(Note 4)
INDOOR check
4
6
01
0F
Press PAUSE (Write) button.
5
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-16
(A)
white luminance point within
the circle shown Fig. 6-1-16
(A)
6
6
01
00
Press PAUSE (Write) button.
OUTDOOR check
7
6
01
3F
Press PAUSE (Write) button.
8
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-16
(B)
white luminance point within
the circle shown Fig. 6-1-16
(B)
9
6
01
00
Press PAUSE (Write) button.
InOut data check
10
Place the ND filter 1.5 (1.0 +
0.4 + 0.1) on the lens.
0.4 + 0.1) on the lens.
11
6
01
4B
Press PAUSE (Write) button.
12
6
02
Check the data changes to
“01”.
“01”.
13
6
0C
Check the data is “00”.
Note 4: If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Click on the first or last page to see other DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man4) service manuals if exist.