Sony DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man2) Service Manual ▷ View online
1-4E
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_L2
E
E
E
Block
Function
6
1
6
1
6
1
Detailed
Code
0
0
1
0
1
1
Symptom/State
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Focus lens initializing failure and zoom
lens initializing failure occur simulta-
neously.
lens initializing failure occur simulta-
neously.
Self-diagnosis Code
Repaired b
y:
Correction
Inspect the lens block focus reset sensor (Pin 7, of CN3101 of VC-
537 board) when focusing is performed when the touch panel is
operated in the focus manual mode and the focus motor drive circuit
(IC3101 of VC-537 board) when the focusing is not performed.
537 board) when focusing is performed when the touch panel is
operated in the focus manual mode and the focus motor drive circuit
(IC3101 of VC-537 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qa, of CN3101 of
VC-537 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC3101 of VC-537
board) when zooming is not performed.
VC-537 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC3101 of VC-537
board) when zooming is not performed.
Inspect the flexible board for breakage or loose connection.
If not faulty, inspect the focus and zoom motor drive circuit (IC3101
of VC-537 board).
If not faulty, inspect the focus and zoom motor drive circuit (IC3101
of VC-537 board).
1-6. PRECAUTION ON REPLACING THE VC-537 BOARD
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value.
Exif Model Data
Page
C
C
C
Data
DCR-HC51E
35
31
45
DCR-HC52
35
32
00
Address
D2
D3
D4
DCR-HC52E
35
32
45
DCR-HC53E
35
33
45
DCR-HC54
35
34
00
DCR-HC54E
35
34
45
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
Note:
To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
2-1
2. DISASSEMBLY
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2-2
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_L2
2-1. IDENTIFYING PARTS
2-2-1. OVERALL SECTION
- Front Cabinet Block
- Microphome Unit
- Cabinet (L)
- Cabinet (Upper (2122))
- Microphome Unit
- Cabinet (L)
- Cabinet (Upper (2122))
2-2-2. BOTTOM FRAME SECTION
- JK-367 Board
- Bottom Frame
- BT-EVF Section
- Bottom Frame
- BT-EVF Section
2-2-3. CABINT (L) SECTION
- VC-537 Board
- CD-735 Board
- Lens Device LSV-1171A
- Mechanism Deck
- Control Key Block (SS21200)
- CD-735 Board
- Lens Device LSV-1171A
- Mechanism Deck
- Control Key Block (SS21200)
2-2-4. CABINET (R) SECTION
- Loud Speaker
- CF-111 Board
- LCD Panel Block
- CF-111 Board
- LCD Panel Block
BT-EVF Section
⋅
LB-137 Board
⋅
AV-125 Board
⋅
FP-626 Flexible Board
Cabinet (L) Section
⋅
VC-537 Board
⋅
CD-735 Board
Cabinet (R) Section
⋅
CF-111 Board
⋅
PD-358 Board
⋅
FP-386 Flexible Board
⋅
FP-625 Flexible Board
Front Cabinet Block
Bottom Frame
- DISASSEMBLY FLOW -
Cabinet (Upper (2122))
Cabinet (L)
JK-367 Board
2-3
DCR-HC51E/HC52/HC52E/HC53E/HC54/HC54E_L2
2-2. DISASSEMBLY
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (R) Section (
1
-1 to
1
-14)
2
Front Cabinet Block (
2
-1 to
2
-6)
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
1
Cabinet (R)
Section
(See Page 2-6)
1
-1
(Open)
1
-2 (#2)
1
-3
1
-4
1
-5
2
-1 (#2)
2
-3
2
-4 (#1)
2
-5 (#1)
2
-6
2
-2 (#2)
Note: On installation of the NS knob,
adjust the position of the NS
switch and the NS knob.
1
-12
(Boss)
1
-11
(Boss)
1
-6
(#2)
1
-7
(#2)
1
-14
1
-13
1
-9
(#2)
1
-8
(Open)
2
Front Cabinet
Block
1
-10
(Claw)
Bottom Frame
Section
Section
(See Page 2-4)
Click on the first or last page to see other DCR-HC51E / DCR-HC52 / DCR-HC52E / DCR-HC53E / DCR-HC54 / DCR-HC54E (serv.man2) service manuals if exist.