Sony DCR-HC30 (serv.man3) Service Manual ▷ View online
6-26
DCR-HC30/HC30E
9. Color Reproduction Adjustment
Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Video terminal of AUDIO/VIDEO jack
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
33, 35, 3A, 3B
Specified Value
All color luminance points should settle
within each color reproduction frame.
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment” and “Optical Axis Adjustment”.
back adjustment” and “Optical Axis Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
NTSC model : DCR-HC30
PAL model
PAL model
: DCR-HC30E
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 6, address: 48, and set data: 02.
3)
Select page: 6, address: 9D, set the following data, and press
the PAUSE button.
the PAUSE button.
7D (NTSC), 82 (PAL)
4)
Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.
button.
5)
Select page: F, address: 80, set the following data, and press
the PAUSE button.
the PAUSE button.
37 (NTSC), B7 (PAL)
6)
Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
the burst luminance point to the burst position of the color
reproduction frame.
7)
Change the data of page: F, address: 33, 35, 3A and 3B, and
settle each color luminance point in each color reproduction
frame.
settle each color luminance point in each color reproduction
frame.
Note:
Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
commander before changing the addresses. If not, the new data
will not be written to the memory.
Processing after Completing Adjustments:
1)
1)
Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
button.
2)
Select page: 6, address: 48, and set data: 00.
3)
Select page: 6, address: 9D, and set data: 00.
4)
Select page: 0, address: 01, and set data: 00.
Burst position
For NTSC model
Burst position
For PAL model
Fig. 6-1-12.
6-27
DCR-HC30/HC30E
10. MAX GAIN Adjustment
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
19
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment” and “Optical Axis Adjustment”.
back adjustment” and “Optical Axis Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Note4:
NTSC model : DCR-HC30
PAL model
PAL model
: DCR-HC30E
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
02
Set the data.
3
6
96
Set the following data.
1F (NTSC), 15(PAL)
1F (NTSC), 15(PAL)
4
6
97
00
Set the data.
5
6
01
6F
Set the data, and press PAUSE
button.
button.
6
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
Note5:
The adjustment data will be automatically input to page: F, address:
19.
19.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
48
00
Set the data.
2
6
96
00
Set the data.
3
6
97
00
Set the data.
4
6
01
00
Set the data, and press PAUSE
button.
button.
5
0
01
00
Set the data.
11. LV Standard Data Input
And adjust the normal coefficient of the light value.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Display data of page 1 (Note4)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
1A, 1B
Specified Value
0FB0 to 1050
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment”, “Optical Axis Adjustment”.
back adjustment”, “Optical Axis Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Note4:
Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Display data
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
02
Set the data.
3
6
01
0D
Set the data, and press PAUSE
button.
button.
4
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
5
0
03
1E
Set the data.
6
1
Check that the display data (Note5)
satisfies the specified value.
satisfies the specified value.
Note5:
The adjustment data will be automatically input to page: F, address:
1A, 1B.
1A, 1B.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
6
48
00
Set the data.
3
0
03
00
Set the data.
4
0
01
00
Set the data.
5
Perform “Auto White Balance
Standard Data Input”.
Standard Data Input”.
6-28
DCR-HC30/HC30E
12. Auto White Balance Standard Data Input
Adjust the white balance reference at 3200K.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
2A to 2D
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment”, “Optical Axis Adjustment” and “Color
reproduction adjustment”.
back adjustment”, “Optical Axis Adjustment” and “Color
reproduction adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
02
Set the data.
3
Wait for 2 sec.
4
6
01
11
Set the data, and press PAUSE
button.
button.
5
6
01
0B
Set the data, and press PAUSE
button.
button.
6
6
02
Check that the data changes to
“01”. (Note4)
“01”. (Note4)
Note4:
The adjustment data will be automatically input to page: F, address:
2A to 2D.
2A to 2D.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
6
48
00
Set the data.
3
0
01
00
Set the data.
4
Perform “Auto White Balance
Adjustment”.
Adjustment”.
13. Auto White Balance Adjustment
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.
If it is not correct, auto white balance and color reproducibility will
be poor.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
Filter C14 for color temperature
correction
correction
Adjustment Page
F
Adjustment Address
2E to 31, 3E to 41
Note1:
This adjustment should be carried out upon completion of “Auto
White Balance Standard Data Input”.
White Balance Standard Data Input”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Note4:
NTSC model : DCR-HC30
PAL model
PAL model
: DCR-HC30E
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Place the C14 filter for color
temperature correction on the lens.
temperature correction on the lens.
2
0
01
01
Set the data.
3
6
48
02
Set the data.
4
F
3E
2A
Set the data, and press PAUSE
button.
button.
5
F
3F
Set the following data, and press
PAUSE button.
00 (NTSC), C0 (PAL)
PAUSE button.
00 (NTSC), C0 (PAL)
6
F
40
Set the following data, and press
PAUSE button.
5D (NTSC), 5C (PAL)
PAUSE button.
5D (NTSC), 5C (PAL)
7
F
41
00
Set the data, and press PAUSE
button.
button.
8
6
01
83
Set the data, and press PAUSE
button.
button.
9
6
01
81
Set the data, and press PAUSE
button.
button.
10
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
Note5:
The adjustment data will be automatically input to page: F, address:
2E to 31.
2E to 31.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
6
48
00
Set the data.
3
0
01
00
Set the data.
4
Perform “White Balance Check”.
6-29
DCR-HC30/HC30E
14. White Balance Check
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
Filter C14 for color temperature
correction
ND filter 1.0 and 0.4 and 0.1
correction
ND filter 1.0 and 0.4 and 0.1
Measurement Point
Video terminal of
Display data
AUDIO/VIDEO
of page 1 (Note3)
jack
Measuring Instrument
Vectorscope
Adjustment
remote commander
remote commander
Specified Value 1
Fig. 6-1-13. A to B
Specified Value 2
R ratio : 29C0 to 2A40 (NTSC)
2A80 to 2B00 (PAL)
B ratio : 5CC0 to 5D40 (NTSC)
5BC0 to 5C40 (PAL)
Specified Value 3
8000 to 8BC0
Note1:
Perform “Auto White Balance Adjustment” before this adjustment.
If not performed, R ratio data and B ratio data may not satisfy the
specified value 2.
If not performed, R ratio data and B ratio data may not satisfy the
specified value 2.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Displayed data of the adjustment remote commander.
1 : XX : XX
Display data
Note4:
NTSC model : DCR-HC30
PAL model
PAL model
: DCR-HC30E
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data
Procedure
Indoor white balance check
1
Check that the lens is not covered
with either filter.
with either filter.
2
6
48
02
Set the data.
3
6
01
0F
Set the data, and press PAUSE
button.
button.
4
Check that the center of the white
luminance point is within the
circle shown Fig. 6-1-13. A.
luminance point is within the
circle shown Fig. 6-1-13. A.
5
6
01
00
Set the data, and press PAUSE
button.
button.
Outdoor white balance check
6
Place the C14 filter on the lens.
7
6
01
3F
Set the data, and press PAUSE
button.
button.
8
Check that the center of the white
luminance point is within the
circle shown Fig. 6-1-13. B.
luminance point is within the
circle shown Fig. 6-1-13. B.
9
0
03
04
Set the data.
10
1
Check that the display data
(Note3) satisfies the R ratio
specified value.
(Note3) satisfies the R ratio
specified value.
11
0
03
05
Set the data.
12
1
Check that the display data
(Note3) satisfies the B ratio
specified value.
(Note3) satisfies the B ratio
specified value.
13
Remove the C14 filter.
LV data check
14
Place the ND filter 1.5
(1.0+0.1+0.4) on the lens.
(1.0+0.1+0.4) on the lens.
15
6
01
00
Set the data, and press PAUSE
button.
button.
16
0
03
06
Set the data.
17
1
Check that the display data
(Note3) satisfies the specified
value 3.
(Note3) satisfies the specified
value 3.
Processing after Completing Adjustments
Order Page Address Data
Procedure
1
0
03
00
Set the data.
2
6
01
00
Set the data, and press PAUSE
button.
button.
3
Remove the ND filter.
R-Y
2mm
B-Y
2mm
R-Y
B-Y
0.5mm
1mm
3mm
3mm
Fig. 6-1-13 (A).
Fig. 6-1-13 (B).
Click on the first or last page to see other DCR-HC30 (serv.man3) service manuals if exist.