Sony DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man4) Service Manual ▷ View online
6-2
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
Precaution on Replacing the VC-439 Board
• Perform “Exif Model Data Check” mentioned below, and also the adjustment items necessary after VC Board re-
placement.
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replacing etc., check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
When the data has changed because of board replacing etc., check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
Note:
To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
B7
B8
B9
BA
Page
A
A
A
A
Data
DCR-DVD505
35
30
35
00
DCR-DVD905
39
30
35
00
DCR-DVD505E
35
30
35
45
DCR-DVD905E
39
30
35
45
6-3
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
Table 6-1-1 (1)
1-1. Adjusting items when replacing main parts and boards
•
Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1:
The Automatic Adjustment Program does not support.
Note 2:
When replacing the drive block, reset the data of page: 4, address: DC to EB to “00”. (Refer to “Record of Use check (Drive
section)” of “6-3. SERVICE MODE”)
section)” of “6-3. SERVICE MODE”)
Lens device
Drive block (Note 2)
LCD block LCD9001 (LCD panel)
LCD block D9001 (LCD backlight)
EVF block LCD9002 (LCD panel)
FL19800 block FLASH unit
MIC unit
CM-069 board IC6001 (CMOS imager)
CM-069 board SE6801, 6802 (PITCH, YAW sensor)
MA-442 board IC3301 (MIC AMP)
MA-442 board IC3351 (Sub MIC AMP)
MD-129 board IC4001 (RF process)
MD-129 board IC4101 (DVD DSP)
MD-129 board IC4302 (DVD mecha drive)
PD-274 board IC5701 (LCD driver)
VC-439 board IC2001 (CDS, A/D conv.)
VC-439 board IC2501, X2501 (Clock generator)
VC-439 board IC2801 (Video/Audio DSP)
VC-439 board IC2901 (Video, Audio I/O)
VC-439 board IC3401 (Aspect ratio converter)
VC-439 board IC5102 (EVF driver)
VF-173 board D5801 (EVF backlight)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
Initialization of F, 63 to 6F page data
Initialization of C, 1C page data
15, 17, 1A, 1B, page data
Initialization of F, 63 to 6F page data
Initialization of C, 1C page data
(Note 1)
Origin oscillation check
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
Differential gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
Differential gain adj.
CAMERA
adjustment 2
adjustment 2
Flange back adj.
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
F No. & ND light qualiy
standard data input
Mechanical shutter adj
Linear matrix adj.
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
standard data input
Mechanical shutter adj
Linear matrix adj.
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
CAMERA
adjustment 5
adjustment 5
White defect adj.
z
CAMERA
adjustment 6
adjustment 6
Black defect adj.
z
z
Strobe light level adj.
Strobe white balance adj.
Strobe white balance adj.
CAMERA
adjustment 8
adjustment 8
Steady shot check
z
LCD automatic adj.
V-COM adj. (LCD)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Sample hold phase adj.
white balance adj. (LCD)
Sample hold phase adj.
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Internal 4ch microphone sensitivity adj.
z
z
z
POWER adj.
z
z
z
z
DVD-R adj.
z
z
z
z
DVD-RW adj.
z
z
z
z
DVD+RW adj.
z
z
z
z
LCD
adjustment
adjustment
CAMERA
adjustment 4
adjustment 4
Adjustment
z
Parts replacement
Replaceed parts
Block replacement
z
VIDEO
adjustment
adjustment
CAMERA
adjustment 7
adjustment 7
Adjusting item
(Note 1)
CAMERA
adjustment 1
adjustment 1
AUDIT
EVF
adjustment
adjustment
Touch panel
adjustment
adjustment
Touch panel adj.
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
6-4
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
•
Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Table 6-1-1 (2)
Note 3:
When the repair is finished,
confirm the following items.
confirm the following items.
1. Shoot the all black subject (Attach
the lens cap and shoot), and con-
firm that a vertical line is not dis-
played in the center of the screen,
and that there is no difference in
left-right brightness level of the
screen.
firm that a vertical line is not dis-
played in the center of the screen,
and that there is no difference in
left-right brightness level of the
screen.
2. Shoot a subject of low light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
3. Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“Differencal Gain Adjustment”.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“Differencal Gain Adjustment”.
Note 4:
IC3101 (Flash memory) on
the VC-439 board and
IC4202 (Flash memory) on
the MD-129 board cannot be
replaced.
the VC-439 board and
IC4202 (Flash memory) on
the MD-129 board cannot be
replaced.
Note 5:
When replacing the VC-439
board, perform “Exif Model
Data Check” after replace-
ment.
board, perform “Exif Model
Data Check” after replace-
ment.
CM-069 board (COMPLETE)
MA-442 board (COMPLETE)
MD-129 board (COMPLETE)
PD-274 board (COMPLETE)
VC-439 board (COMPLETE) (Note 5)
VF-173 board (COMPLETE)
VC-439 board IC2602 (EEPROM)
VC-439 board IC3002 (EEPROM)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
15, 17, 1A, 1B, page data
z
z
Initialization of F, 63 to 6F page data
z
z
Initialization of C, 1C page data
z
z
(Note 1)
Origin oscillation check
z
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
Differential gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
Differential gain adj.
CAMERA
adjustment 2
adjustment 2
Flange back adj.
z
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
z
F No. & ND light qualiy
standard data input
Mechanical shutter adj
Linear matrix adj.
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
standard data input
Mechanical shutter adj
Linear matrix adj.
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
CAMERA
adjustment 5
adjustment 5
White defect adj.
z
z
z
CAMERA
adjustment 6
adjustment 6
Black defect adj.
z
z
z
Strobe light level adj.
Strobe white balance adj.
Strobe white balance adj.
CAMERA
adjustment 8
adjustment 8
Steady shot check
z
LCD automatic adj.
V-COM adj. (LCD)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Sample hold phase adj.
white balance adj. (LCD)
Sample hold phase adj.
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Internal 4ch microphone sensitivity adj.
z
z
z
POWER adj.
z
DVD-R adj.
z
DVD-RW adj.
z
DVD+RW adj.
z
Board
replacement
z
z
CAMERA
adjustment 7
adjustment 7
CAMERA
adjustment 4
adjustment 4
CAMERA
adjustment 1
adjustment 1
AUDIT
z
z
z
z
z
z
z
z
z
z
Adjusting item
Adjustment
(Note 1)
VIDEO
adjustment
adjustment
EEPROM
replacement
LCD
adjustment
adjustment
EVF
adjustment
adjustment
Touch panel
adjustment
adjustment
Touch panel adj.
z
z
z
z
z
z
6-5
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
1-2. List of service tools
• Oscilloscope
• Color monitor
• Vectorscope
• Frequency counter
• Audio level meter
• Audio generator
• Audio attenuator
• Audio distortion meter
• Amplifier built-in speaker for PC
• Adjustment sound source file
Fig. 6-1-1 (1)
Note 1:
Personal computer
OS:
OS:
Windows 98/98SE/Me/2000/XP Home/XP Pro (Camera Section)
Windows 2000/XP Home/XP Pro (Drive Section)
Windows 2000/XP Home/XP Pro (Drive Section)
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
Note 2:
The following programs and driver must already be installed in the personal computer. (Contact our service headquater of each
area how to get the programs and driver)
• SeusCam
area how to get the programs and driver)
• SeusCam
• Optical power meter driver
• AUDIT
Personal computer
(Note 1, 2)
(Note 1, 2)
J-1
HASP key and application
for adjustment (SeusCam)
for adjustment (SeusCam)
Contact our service headquater of each area
how to get the application for adjustment
(SeusCam) and HASP key.
how to get the application for adjustment
(SeusCam) and HASP key.
J-2
USB cable
1-831-369-21
1-831-369-21
J-3
J-4
Adjustment remote
commander
(RM-95)
J-6082-053-B
commander
(RM-95)
J-6082-053-B
J-13
J-9
J-7
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-10
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
J-11
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-12
Minipattern box
J-6082-353-B
J-6082-353-B
Siemens star chart
J-6080-875-A
J-6080-875-A
Filter for color
temperature correction
(C14)
J-6080-058-A
temperature correction
(C14)
J-6080-058-A
J-14
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
J-8
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
J-6
LANC cable
J-6082-442-A
J-6082-442-A
J-5
Adjustment remote
commander
(NEW LANC JIG)
J-6082-565-A
commander
(NEW LANC JIG)
J-6082-565-A
J-15
Camera table
J-6082-384-A
J-6082-384-A
Click on the first or last page to see other DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man4) service manuals if exist.