Sony DCR-DVD404E / DCR-DVD405 / DCR-DVD405E / DCR-DVD805 / DCR-DVD805E (serv.man4) Service Manual ▷ View online
DCR-DVD404E/DVD405/DVD405E/DVD805/DVD805E_ADJ
6-2
Precaution on Replacing the VC-427 Board
• Perform “Exif Model Data Check” mentioned below, and also the adjustment items necessary after VC Board re-
placement.
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replacing etc., check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
When the data has changed because of board replacing etc., check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
Note:
To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
B7
B8
B9
BA
Page
A
A
A
A
Data
DCR-DVD405
34
30
35
00
DCR-DVD805
38
30
35
00
DCR-DVD404E
34
30
34
45
DCR-DVD405E
34
30
35
45
DCR-DVD805E
38
30
35
45
DCR-DVD404E/DVD405/DVD405E/DVD805/DVD805E_ADJ
6-3
Table 6-1-1 (1)
1-1. Adjusting items when replacing main parts and boards
•
Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1:
The Automatic Adjustment Program does not support.
Lens device
Drive block
LCD block LCD9001 (LCD panel)
EVF block LCD9002 (LCD panel)
FL19500 block FLASH unit
MIC unit
CD-602 board IC5202 (CCD imager)
CD-602 board IC5203, X5201 (Timing generator)
CD-602 board IC5205 (S/H)
FR-425 board SE5501, 5502 (PITCH, YAW sensor)
MA-441 board IC3301 (MIC AMP)
MA-441 board IC3351 (Sub MIC AMP)
MD-127 board IC4001 (RF process)
MD-127 board IC4101 (DVD DSP)
MD-127 board IC4302 (DVD mecha drive)
PD-272 board IC5701 (LCD driver)
PD-272 board D5704 - 5706 (LCD backlight)
VC-427 board IC2803 (Video/Audio DSP)
VC-427 board IC2901 (Video, Audio I/O)
VC-427 board IC3401 (Aspect ratio converter)
VC-427 board IC5102 (EVF driver)
VF-172 board D302 (EVF backlight)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
Initialization of E, F, 14, 19, 1E, 1F page data
Initialization of C, 1C page data
15, 17, 1A, 1B, page data
Initialization of E, F, 14, 19, 1E, 1F page data
Initialization of C, 1C page data
(Note 1)
67.5MHz/54MHz origin oscillation check
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.
CAMERA
adjustment 2
adjustment 2
Flange back adj.
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
Mixed color compensation adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.
CAMERA
adjustment 6
adjustment 6
Steady shot check
z
LCD automatic adj.
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Internal 4ch microphone sensitivity adj.
z
z
z
POWER adj.
z
z
z
z
DVD-R adj.
z
z
z
z
DVD-RW adj.
z
z
z
z
DVD+RW adj.
z
z
z
z
z
z
z
VIDEO
adjustment
adjustment
Adjusting item
(Note 1)
Adjustment
AUDIT
z
LCD
adjustment
adjustment
EVF
adjustment
adjustment
Touch panel
adjustment
adjustment
Touch panel adj.
z
z
z
z
z
z
z
z
z
z
z
z
z
CAMERA
adjustment 5
adjustment 5
CAMERA
adjustment 1
adjustment 1
z
CAMERA
adjustment 4
adjustment 4
z
z
Replaceed parts
Block replacement
Parts replacement
DCR-DVD404E/DVD405/DVD405E/DVD805/DVD805E_ADJ
6-4
•
Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Table 6-1-1 (2)
Note 2:
When the repair is finished,
confirm the following items.
confirm the following items.
1. Shoot the all black subject (Attach
the lens cap and shoot), and con-
firm that a vertical line is not dis-
played in the center of the screen,
and that there is no difference in
left-right brightness level of the
screen.
firm that a vertical line is not dis-
played in the center of the screen,
and that there is no difference in
left-right brightness level of the
screen.
2. Shoot a subject of low light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
3. Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
Note 3:
IC3101 (Flash memory) on
the VC-427 board and
IC4202 (Flash memory) on
the MD-128 board cannot be
replaced.
the VC-427 board and
IC4202 (Flash memory) on
the MD-128 board cannot be
replaced.
Note 4:
When replacing the VC-427
board, perform “Exif Model
Data Check” after replace-
ment.
board, perform “Exif Model
Data Check” after replace-
ment.
CD-602 board (COMPLETE)
FR-425 board (COMPLETE)
MA-441 board (COMPLETE)
MD-127 board (COMPLETE)
PD-272 board (COMPLETE)
VC-427 board (COMPLETE) (Note 4)
VF-172 board (COMPLETE)
VC-427 board IC2602 (EEPROM)
VC-427 board IC3002 (EEPROM)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
15, 17, 1A, 1B, page data
z
z
Initialization of E, F, 14, 19, 1E, 1F page data
z
z
Initialization of C, 1C page data
z
z
(Note 1)
67.5MHz/54MHz origin oscillation check
z
z
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.
CAMERA
adjustment 2
adjustment 2
Flange back adj.
z
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
z
Mixed color compensation adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.
CAMERA
adjustment 6
adjustment 6
Steady shot check
z
LCD automatic adj.
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Internal 4ch microphone sensitivity adj.
z
z
z
POWER adj.
z
DVD-R adj.
z
DVD-RW adj.
z
DVD+RW adj.
z
z
z
z
z
Adjusting item
Adjustment
(Note 1)
VIDEO
adjustment
adjustment
EEPROM
replacement
Board
replacement
z
z
z
z
z
z
z
z
z
z
CAMERA
adjustment 5
adjustment 5
LCD
adjustment
adjustment
CAMERA
adjustment 4
adjustment 4
CAMERA
adjustment 1
adjustment 1
AUDIT
Touch panel
adjustment
adjustment
Touch panel adj.
EVF
adjustment
adjustment
z
z
z
DCR-DVD404E/DVD405/DVD405E/DVD805/DVD805E_ADJ
6-5
1-2. List of service tools
• Oscilloscope
• Color monitor
• Vectorscope
• Frequency counter
• Audio level meter
• Audio generator
• Audio attenuator
• Audio distortion meter
• Amplifier built-in speaker for PC
• Adjustment sound source file
Fig. 6-1-1 (1)
Note 1:
Personal computer
OS:
OS:
Windows 98/98SE/Me/2000/XP Home/XP Pro (Camera Section)
Windows 2000/XP Home/XP Pro (Drive Section)
Windows 2000/XP Home/XP Pro (Drive Section)
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
Note 2:
The following programs and driver must already be installed in the personal computer. (Contact our service headquater of each
area how to get the programs and driver)
• SeusCam
area how to get the programs and driver)
• SeusCam
• Optical power meter driver
• AUDIT
Personal computer
(Note 1, 2)
(Note 1, 2)
J-1
HASP key and application
for adjustment (SeusCam)
for adjustment (SeusCam)
Contact our service headquater of each area
how to get the application for adjustment
(SeusCam) and HASP key.
how to get the application for adjustment
(SeusCam) and HASP key.
J-2
USB cable
1-831-369-21
1-831-369-21
J-3
J-4
Adjustment remote
commander
(RM-95)
J-6082-053-B
commander
(RM-95)
J-6082-053-B
J-14
J-9
J-7
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-10
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
J-11
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-12
Minipattern box
J-6082-353-B
J-6082-353-B
Siemens star chart
J-6080-875-A
J-6080-875-A
Filter for color
temperature correction
(C14)
J-6080-058-A
temperature correction
(C14)
J-6080-058-A
J-15
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
J-8
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
J-6
LANC cable
J-6082-442-A
J-6082-442-A
J-5
Adjustment remote
commander
(NEW LANC JIG)
J-6082-565-A
commander
(NEW LANC JIG)
J-6082-565-A
Mixed color
compensation chart
compensation chart
For PTB-450:
J-6082-558-A
J-6082-558-A
For PTB-1450:
J-6082-561-A
J-6082-561-A
J-13
Click on the first or last page to see other DCR-DVD404E / DCR-DVD405 / DCR-DVD405E / DCR-DVD805 / DCR-DVD805E (serv.man4) service manuals if exist.