Sony CCD-TRV13E / CCD-TRV23E / CCD-TRV3E / CCD-TRV45E / CCD-TRV55E / CCD-TRV65E / CCD-TRV69E / CCD-TRV715 / CCD-TRV75 / CCD-TRV75PK Service Manual ▷ View online
5-3
2.5 INCH LCD MODEL
Fig. 5-1-3.
Color monitor
Vector scope
Terminated at 75
Ω
Lens block
CD-197 board
CN401
CN401
Extension cable(16P)
(J-6082-357-A)
(J-6082-357-A)
Need not connected
VIDEO terminal
CN909
CN551
CN902
CN903
CN901
CN001
CN905
CN906 CN908
CN914
CN910
CN911
CN912
Battery switch
MA-331 board CN303
Extension cable(48P)
(J-6082-188-A)
(J-6082-188-A)
CF-50
board
CN001
board
CN001
PD-92 board
CN580
CN580
PD-92 board
CN5701
CN5501
CN5001
CN5805
CN5802
CN5803
CN5804
Multi CPC jig
(J-6082-311-A)
(J-6082-311-A)
Must be connected when
performing the LCD system
adjustments.
performing the LCD system
adjustments.
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
Must be connected when
performing the VIDEO system.
performing the VIDEO system.
CN935
CN932
CN934
CN801
CN931
CN933
DD-105
board
board
LANC
jack
jack
Adjusting
remote
commander
remote
commander
Regulaterd power supply
(8.4
(8.4
±
0.1 Vdc)
Battery
terminal
(Note 2)
terminal
(Note 2)
VC-195
board
board
CN501
Note 1 :
2.5” LCD model : CCD-TRV3E/TRV13E/TRV23E/
TRV65E/TRV69E
Note 2 :
Connect the adjusting remote commander to the LANC
jack, and set the HOLD switch to the “ADJ” side, or
press the battery switch of the battery terminal using
adhesive tape, etc. or use the AC power adaptor.
jack, and set the HOLD switch to the “ADJ” side, or
press the battery switch of the battery terminal using
adhesive tape, etc. or use the AC power adaptor.
5-4
3/3.5 INCH LCD MODEL
Fig. 5-1-4.
Color monitor
Vector scope
Terminated at 75
Ω
Lens block
CD-198 board
CN401
CN401
Extension cable(16P)
(J-6082-357-A)
(J-6082-357-A)
Need not connected
VIDEO terminal
CN909
CN551
CN902
CN903
CN901
CN001
CN905
CN906 CN908
CN914
CN910
CN911
CN912
MA-312 board
CN303
CN303
Extension cable(48P)
(J-6082-188-A)
(J-6082-188-A)
CF-51
board
CN001
board
CN001
PD-93 board
CN580
CN580
PD-93 board
CN4701
CN4501
CN4601
CN4805
CN4802
CN4803
CN4804
Multi CPC jig
(J-6082-311-A)
(J-6082-311-A)
Must be connected when
performing the LCD system.
performing the LCD system.
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
Must be connected when
performing the VIDEO system.
performing the VIDEO system.
CN935
CN932
CN934
CN801
CN931
CN933
DD-105
board
board
LANC
jack
jack
Adjusting
remote
commander
remote
commander
Regulaterd power supply
(8.4
(8.4
±
0.1 Vdc)
Battery
terminal
(Note 2)
terminal
(Note 2)
CN501
VC-195
board
board
Battery switch
Note 1 :
3” LCD model : CCD-TRV75/TRV75PK/TRV715
3.5”LCD MODEL ; CCD-TRV45E/TRV55E
3.5”LCD MODEL ; CCD-TRV45E/TRV55E
Note 2 :
Connect the adjusting remote commander to the LANC
jack, and set the HOLD switch to the “ADJ” side, or
press the battery switch of the battery terminal using
adhesive tape, etc. or use the AC power adaptor.
jack, and set the HOLD switch to the “ADJ” side, or
press the battery switch of the battery terminal using
adhesive tape, etc. or use the AC power adaptor.
5-5
1-1-3.Precaution
1. Setting the Switch
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
1. POWER switch (MA-312/331 board) .................... CAMERA
2. NIGHT SHOT switch (Lens Block) ................................ OFF
adjustments without loading cassette.
1. POWER switch (MA-312/331 board) .................... CAMERA
2. NIGHT SHOT switch (Lens Block) ................................ OFF
(Night shot model)
3. DEMO MODE (Menu display) ....................................... OFF
4. DIGITAL ZOOM (Menu display) ................................... OFF
5. STEADY SHOT (Menu display) .................................... OFF
6. DISPLAY (Menu display) ................................. V-OUT/LCD
4. DIGITAL ZOOM (Menu display) ................................... OFF
5. STEADY SHOT (Menu display) .................................... OFF
6. DISPLAY (Menu display) ................................. V-OUT/LCD
7. FOCUS switch (MF-8500/MR-8500) ................... MANUAL
(Manual Focus model)
8. PROGRAM AE (CF-50/51 board) .................................. Auto
9. BACK LIGHT (CF-50/51 board) .................................... OFF
10. PICTURE EFECT (CF-50/51 board) .............................. OFF
11. 16 : 9 WIDE (Menu display) ........................................... OFF
9. BACK LIGHT (CF-50/51 board) .................................... OFF
10. PICTURE EFECT (CF-50/51 board) .............................. OFF
11. 16 : 9 WIDE (Menu display) ........................................... OFF
2. Adjusting Procedure
Adjust in the given order.
Fig. 5-1-5.
3. Subject
1) Color bar chart (Standard picture frame)
Adjust the picture frame as shown in Fig. 5-1-5. if adjustments
are performed using the color bar chart.
(Standard picture frame)
are performed using the color bar chart.
(Standard picture frame)
2) White pattern (Standard picture frame)
Remove the color bar chart from the pattern box, and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
clear chart in its place. (Do not perform zoom operations during
this time.)
3) Chart for flange back adjustment
Combine a white A0 size (1189 mm x 841 mm) paper to a black
one, and make the chart shown in Fig. 5-1-6.
one, and make the chart shown in Fig. 5-1-6.
Fig. 5-1-6.
Note :
Use the non-reflecting and non-glazing vellum paper
whose size is more than A0, and make the boundary
between white and black to be smoothly flat.
whose size is more than A0, and make the boundary
between white and black to be smoothly flat.
Color bar chart standard picture trame
H
A
B
A=B
B
A
0
±
0.1 msec
V
Enlargement
Difference in level
A
B
Electronic beam
scanning frame
scanning frame
CRT picture frame
Fig. b. (TV monitor picture)
Yellow
Cyan
Green
White
Magenta
Red
Blue
Yellow
Cyan
Green
White
Magenta
Red
Blue
Fig. a. (Video output terminal
output wavefom)
output wavefom)
Adjust the camera zoom and direction to obtain the output wavefom
shown in Fig. a and the TV monitor display shown in Fig. b.
shown in Fig. a and the TV monitor display shown in Fig. b.
841 mm
1189 mm
White
Black
5-6
1-1-4. Adjusting Remote Commander
The adjusting remote commander is used for changing the
calculation coefficient in signal processing, EVR data, etc. The
adjusting remote commander performs bi-directional
communication with the unit using the remote commander signal
line (LANC). The resultant data of this bi-directional communication
is written in the non-volatile memory.
calculation coefficient in signal processing, EVR data, etc. The
adjusting remote commander performs bi-directional
communication with the unit using the remote commander signal
line (LANC). The resultant data of this bi-directional communication
is written in the non-volatile memory.
1. Using the adjusting remote commander
1) Connect the adjusting remote commander to the LANC terminal.
2) Adjust the HOLD switch of the adjusting remote commander to
2) Adjust the HOLD switch of the adjusting remote commander to
“HOLD” (SERVICE position).
If it has been properly connected, the LCD on the adjusting remote
commander will display as shown in Fig. 5-1-7.
commander will display as shown in Fig. 5-1-7.
Fig. 5-1-7.
3) Operate the adjusting remote commander as follows.
• Changing the page
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCH– button is
pressed. There are altogether 16 pages, from 0 to F.
pressed, and decreases when the EDIT SEARCH– button is
pressed. There are altogether 16 pages, from 0 to F.
Table 5-1-1.
• Changing the address
The address increases when the FF (
)) button is pressed,
and decreases when the REW (
0) button is pressed. There
are altogether 256 addresses, from 00 to FF.
• Changing the data (Data setting)
The data increases when the PLAY (
() button is pressed,
and decreases when the STOP (
p) button is pressed.
There are altogether 256 data, from 00 to FF.
• Writing the adjustment data
The PAUSE button must be pressed to write the adjustment
data (D, E, F page) in the nonvolatile memory.
(The new adjustment data will not be recorded in the nonvolatile
memory if this step is not performed.)
4) Select page: 0, address: 01, and set the data to 01, and enables
Page D and E, F to be adjusted.
5) After completing all adjustments, set data: 00 to page: 0, address:
01 and turn off the main power supply (8.4V) once.
2. Precautions upon using the adjusting remote
commander
Mishandling of the adjusting remote commander may erase the
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjustments
and new adjustment data after each adjustment.
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjustments
and new adjustment data after each adjustment.
Page
Data
Address
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 A b c d E F
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Hexadecimal
notation
LCD Display
Decimal notation
conversion value
notation
LCD Display
Decimal notation
conversion value
Click on the first or last page to see other CCD-TRV13E / CCD-TRV23E / CCD-TRV3E / CCD-TRV45E / CCD-TRV55E / CCD-TRV65E / CCD-TRV69E / CCD-TRV715 / CCD-TRV75 / CCD-TRV75PK service manuals if exist.