DOWNLOAD Sony CCD-TRV138 (serv.man2) Service Manual ↓ Size: 515.62 KB | Pages: 49 in PDF or view online for FREE

6-23

CCD-TRV138/TRV238E/TRV338/TRV438E

Set the DC bias of the common electrode drive signal of LCD to
the specified value.
If deviated, the LCD display will be move, producing flicker and
conspicuous vertical lines.

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Measurement Point

Check on LCD screen

Measuring Instrument

Adjustment Page

C

Adjustment Address

52

Specified Value

The brightness difference between
the section-A and section-B is
minimum

Perform “LCD Level Adjustment” before this adjustment.

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

C

52

Change the data so that
brightness of the section A
and section B is equal.

3

C

52

Subtract 8 from the data.

4

C

52

Press PAUSE button.

5

0

01

00

Correct the white balance.
If deviated, the LCD screen color cannot be reproduced.

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Measurement Point

Check on LCD screen

Measuring Instrument

Adjustment Page

C

Adjustment Address

56, 57

Specified Value

LCD screen must not be colored

Check that the data of page: 0, address: 10 is “00”.

Check the white balance only when replacing the fol-
lowing parts. If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC6001

Order Page Address Data

Procedure

1

0

01

01

2

C

56

87

Press PAUSE button.

3

C

57

68

Press PAUSE button.

4

Check that the LCD screen is
not colored. If not colored,
proceed to step 6.

5

C

56

Change the data so that the
LCD screen is not colored.

57

(Note 3)

6

0

01

00

To write in the non-volatile memory (EEPROM), press
the PAUSE button each time to set the data.

A

A

A

A

B

B

B

B

6-24

CCD-TRV138/TRV238E/TRV338/TRV438E

Mechanism Section adjustments, checks, and replacement of
mechanism parts, refer to the separate volume “8mm Video Mecha-
nism Adjustment Manual IX

M2000 Mechanism

”.

Before perform the adjustments, check that the data of page:
0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.

Connect the adjustment remote commander to CN007 of VC-341
board via I/F unit for LANC control (J-6082-521-A) and CPC jig
connector (J-6082-539-A). To operate the adjustment remote com-
mander, connect the AC power adapter (8.4Vdc) to the DC IN
jack of I/F unit for LANC control, or connect the L series Info-
LITHIUM battery to the battery terminal of I/F unit for LANC
control.

1) Refer to “Section 2. DISASSEMBLY” and supply the power

with the cabinet assembly removed. (So that the mechanical
deck can be operated.)

2) Connect the adjustment remote commander.
3) Turn  on the HOLD switch of the adjustment remote com-

mander.

4) Close the cassette compartment without loading a cassette and

complete loading.

5) Select page: 0, address: 01, and set data: 01.
6) Select page: C, address: 14, set data: 01, and press the PAUSE

button of the adjustment remote commander.

7) Select page: D, address: 10, set data: 02, and press the PAUSE

button of the adjustment remote commander.

8) Select page: A, address: 10, set data: 10, and press the PAUSE

button of the adjustment remote commander.

9) Select page: 7, address: 10, set data: 02, and press the PAUSE

button of the adjustment remote commander.

10) Disconnect the power supply of the unit.

By carrying out the above procedure, the unit can be operated
without loading a cassette.
Be sure to carry out “Processing after Operations” after check-
ing the operations.
Set the data of page: A, address: 10 to the following if the
sensor ineffective mode, forced VTR power supply On mode
or forced camera power supply ON mode are to be used to-
gether.

Forced VTR power ON mode ....................................... 12
Forced camera power ON mode ................................... 11

1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: 14, set data: 00, and press the PAUSE

button of the adjustment remote commander.

3) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

4) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

5) Select page: 7, address: 10, set data: E2, and press the PAUSE

button of the adjustment remote commander.

6) Select page: 0, address: 01, and set data: 00.
7) Disconnect the power supply of the unit.

1) Clean the tape path face (tape guide, capstan shaft, pinch roller).
2) Connect the adjustment remote commander.
3) Turn  on the HOLD switch of the adjustment remote com-

mander.

4) Select page: 0, address: 01, and set data: 01.
5) Select page: C, address: 14, set data: 08, and press the PAUSE

button of the adjustment remote commander.
(Be sure to perform “Processing after operation” after com-
pleting adjustments.)

6) Connect the oscilloscope to I/F unit for LANC control.

Channel 1: PB RF (Pin 9 of CN007)
Channel 2 (Trigger): SWP (Pin 5 of CN007)

7) Playback the alignment tape for tracking. (WR5-1NU (NTSC),

WR5-1CU (PAL))

8) Check that the oscilloscope RF waveform is normal at the en-

trance and exit.
If not normal, adjust according to the separate volume “8mm
Video Mechanical Adjustment Manual IX

M2000 Mechanism

”.

9) Perform “Processing after operations”, after completing ad-

justment.

Pin No.

Signal Name

Pin No.

Signal Name

BL

15

EVF VCO

14

EVF VG

BL 4.75

9

PB RF (MON)

3

BPF MONI

6, 8 ,10

GND

TMS

7

REC RF (RF IN)

TDI

TDO

5

SWP

TCK

4

CAP FG

2

IR VIDEO

 Pin No. are those of CN007.

1) Connect the adjustment remote commander, and turn on the

HOLD switch.

2) Select page: 0, address: 01, and set data: 01.
3) Select page: C, address: 14, set data: 00, and press the PAUSE

button of the adjustment remote commander.

4) Select page: 0, address: 01, and set data: 00.
5) Remove the power supply from the unit.

CH1

Entrance 
side

Exit side

Check this section

(Normal waveform)

CH2
(Trigger)

V

6-25

CCD-TRV138/TRV238E/TRV338/TRV438E

Use the following measuring instruments for video section adjust-
ments.

NTSC model: CCD-TRV138/RV338
PAL model: CCD-TRV238E/TRV438E

1) TV monitor
2) Oscilloscope (dual-phenomenon, band width above 30 MHz

with delay mode) (Unless specified otherwise, use a 10 : 1
probe)

3) Frequency counter
4) Digital voltmeter
5) Audio level meter
6) Audio distortion meter
7) Regulated power supply
8) NTSC alignment tapes

•

For tracking adjustment (WR5-1NU)

Parts code: 8-967-995-04

•

For video frequency characteristics adjustment (WR5-10NM)

Parts code: 8-967-995-03

•

For checking Standard 8 mode operations
For LP (WR5-4NL)

Parts code: 8-967-995-51

For SP (WR5-5NSP)

Parts code: 8-967-995-42

The following alignment tapes can also be used.
WR5-4NSP (8-967-995-41)

•

For checking Hi8 mode operations
For LP (WR5-8NLE)

Parts code: 8-967-995-52

For SP (WR5-8NSE)

Parts code: 8-967-995-43

•

For BPF adjustment (WR5-11NS)

Parts code: 8-967-995-71

9) PAL alignment tapes

•

For tracking adjustment (WR5-1CU)

Parts code: 8-967-995-09

•

For video frequency characteristics adjustment (WR5-10CM)

Parts code: 8-967-995-08

•

For checking Standard 8 mode operations
For LP (WR5-4CL)

Parts code: 8-967-995-56

For SP (WR5-5CSP)

Parts code: 8-967-995-47

The following alignment tapes can also be used.
1) WR5-3CL (8-967-995-36)
2) WR5-4CSP (8-967-995-46)

•

For checking Hi8 mode operations
For LP (WR5-8CLE)

Parts code: 8-967-995-57

For SP (WR5-8CSE)

Parts code: 8-967-995-48

•

For BPF adjustment (WR5-11CS)

Parts code: 8-967-995-76

10) Adjustment remote commander (J-6082-053-B)
11) CPC jig connector (J-6082-539-A)
12) I/F unit for LANC control (J-6082-521-A)

6-26

CCD-TRV138/TRV238E/TRV338/TRV438E

CN007

A/V OUT jack

16

1

Audio (black)

Video (yellow)

TV monitor

AC adaptor

AC IN

AC adaptor

CPC lid

Screw (M2)

I/F unit for LANC control
(J-6082-521-A)

CPC jig connector
(J-6082-539-A)

L serices Info
LITHIUM battery (7.2Vdc)

Adjustment
remote commander (RM-95)

Conductor side

LANC jack

AC IN

This set is adjusted in two modes, VTR mode and CAMERA mode.

Some of the adjusting points of the video section are concentrated
at VC-341 board CN007. Connect the measuring instruments via
I/F unit for LANC control (J-6082-521-A) and CPC jig connector
(J-6082-539-A).
The following table shows the pin No. and signal name of CN007.

Pin No.

Signal Name

Pin No.

Signal Name

1

EEP SCK

9

PB RF

2

PB RF

10

REG GND

3

BPF MONI

11

LANC OUT

4

CAP FG

12

LANC IN

5

SWP DIR

13

XLANC PWR ON

6

REG GND

14

EEP SO

7

REC RF

15

EEP SI

8

REG GND

16

XCS EEP

Use either the AC power adaptor or the InfoLITHIUM battery as the power supply of I/F unit for LANC control.

The following table lists the test point of I/F unit of for LANC
control.

Pin No.

Signal Name

Pin No.

Signal Name

BL

15

EVF VCO

14

EVF VG

BL 4.75

9

PB RF (MON)

3

BPF MONI

6, 8, 10

GND

TMS

7

REC RF (RF IN)

TDI

TDO

5

SWP

TCK

4

CAP FG

2

IR VIDEO

 Pin No. are those of CN007.

Connect the measuring instruments as shown in Fig. 6-3-1 and
perform the adjustments.