Sony CCD-TR311 / CCD-TR311E / CCD-TR411E / CCD-TR412E / CCD-TR511E / CCD-TR512E / CCD-TR640E / CCD-TR730E / CCD-TR840E / CCD-TR845E Service Manual ▷ View online
– 5 –
SERVICE NOTE
6
Pull the timing belt in the direction of arrow
A
with a pinsette while pressing the cassette lid
(take care not to damage) to adjust the
bending of a tape.
(take care not to damage) to adjust the
bending of a tape.
7
Let go your hold the cassette
lid and rise the cassette
compartment to take out a cassette.
lid and rise the cassette
compartment to take out a cassette.
A
Pinsette
Timing belt
Press the cassette lid not to rise the
cassette compartment
cassette compartment
+
–
[DC power supply]
(+5V)
Loading motor
Adjust the bending of a tape
Timing belt
1 Refer to 2-1. to remove the front panel block.
2 Refer to 2-2. to remove the cabinet (R) block.
3 Refer to 2-7. to remove the battery panel block.
4 Refer to 2-9. to remove the cabinet (L) block.
5 Add +5V from the DC POWER SUPPLY and unload with a
2 Refer to 2-2. to remove the cabinet (R) block.
3 Refer to 2-7. to remove the battery panel block.
4 Refer to 2-9. to remove the cabinet (L) block.
5 Add +5V from the DC POWER SUPPLY and unload with a
pressing the cassette lid.
2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied (8.4V) to the
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
Method 1.
Connect the servicing remote commander RM-95 (J-6082-053-B)
to the LANC jack, and set the remote commander switch to the
“ADJ” side.
to the LANC jack, and set the remote commander switch to the
“ADJ” side.
Method 2.
Use the DC IN terminal. (Use the AC power adaptor.)
Battery terminal
‘
DC IN terminal
Battery SIG terminal
Battery switch
Battery terminal
’
– 6 –
Note: The self-diagnosis display data will be backed up by the coin-type lithium battery. When this coin-type lithium battery is
disconnected, the self-diagnosis data will be lost by initialization.
1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder what to do.
This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder what to do.
This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
SELF-DIAGNOSIS FUNCTION
2. Self-diagnosis display
When problems occur while the unit is operating, the counter of the
viewfinder shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
viewfinder shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
3. Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
3-1. Display Method
While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds
continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
3-2. Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time
[4] : Occurred fourth time
[2] : Occurred second time
[5] : Occurred fifth time
[3] : Occurred third time
[6] : Occurred the last time
3-3. End of Display
Turning OFF the power supply will end the service mode display.
Viewfinder
Blinks at 3.2 Hz
Refer to page7
Self-Diagnosis Code table
Self-Diagnosis Code table
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service engineer
H : Corrected by dealer
E : Corrected by service engineer
Repair by :
Block
Detail Code
Indicates the appropriate step to be taken
E. g.
31 ... Reload the tape.
32 ... Turn on power again.
E. g.
31 ... Reload the tape.
32 ... Turn on power again.
C
3 1
1 1
C : 3 1 : 1 1
Viewfinder
Light up
Order of previous errors
Backup No.
Self-diagnosis codes
[3]
C : 3 1 : 1 1
[3] C : 3 1 : 1 1
Display window
Control dial
– 7 –
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Use the InfoLITHIUM battery.
Clean with the optional cleaning cassette.
Use the InfoLITHIUM battery.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Inspect the lens block focus reset sensor (Pin
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.
Inspect the lens block focus reset sensor (Pin
!ª of CN551 of VC-195
board) when focusing is performed when the focus dial is rotated in the
focus manual mode and the focus motor drive circuit (IC552 of VC-195
board) when the focusing is not performed.
Note : Use the remote commander RM-95 only for the model without
focus manual mode and the focus motor drive circuit (IC552 of VC-195
board) when the focusing is not performed.
Note : Use the remote commander RM-95 only for the model without
the focus dial.
Inspect the lens block zoom reset sensor (Pin
@¡ of CN551 of VC-195
board) when zooming is performed when the zoom lens is operated and
the zoom motor drive circuit (IC552 of VC195 board) when zooming is
not performed.
the zoom motor drive circuit (IC552 of VC195 board) when zooming is
not performed.
Inspect pitch angular velocity sensor (SE451 of SE-65 board) peripheral
circuits.
circuits.
Inspect yaw angular velocity sensor (SE452 of SE-65 board) peripheral
circuits.
circuits.
4. Self-diagnosis Code Table
Condensation.
Video head is dirty.
Non-standard battery is used.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault
S reel fault
FG fault when starting capstan
FG fault during normal capstan operations
FG fault when starting drum
PG fault when starting drum
FG fault during normal drum operations
PG fault during normal drum operations
Phase fault during normal drum operations
Video head is dirty.
Non-standard battery is used.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault
S reel fault
FG fault when starting capstan
FG fault during normal capstan operations
FG fault when starting drum
PG fault when starting drum
FG fault during normal drum operations
PG fault during normal drum operations
Phase fault during normal drum operations
LOAD direction loading motor time-out
UNLOAD direction loading motor time-
out
out
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault
S reel fault
FG fault when starting capstan
FG fault during normal capstan operations
FG fault when starting drum
PG fault when starting drum
FG fault during normal drum operations
PG fault during normal drum operations
Phase fault during normal drum operations
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Handshake correction function does not
work well.(With pitch angular velocity
sensor output stopped)
Handshake correction function does not
work well.(With yaw angular velocity
sensor output stopped)
work well.(With pitch angular velocity
sensor output stopped)
Handshake correction function does not
work well.(With yaw angular velocity
sensor output stopped)
Self-diagnosis Code
Repaired by:
Block
Function
Detailed
Code
Symptom/State
Correction
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
2
1
2
2
2
3
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
6
1
6
1
6
2
6
2
0
0
0
0
0
0
1
0
1
1
2
0
2
1
2
2
2
3
3
0
3
1
4
0
4
1
4
2
4
3
4
4
1
0
1
1
2
0
2
1
2
2
2
3
3
0
3
1
4
0
4
1
4
2
4
3
4
4
0
0
1
0
0
0
0
1
– 8 –
SERVICE NOTE
1.
Power Supply During Repairs ......................................... 5
2.
To Take out a Cassette when not Eject (Force Eject) ....... 5
Self-Diagnosis Function
1.
Self-diagnosis function .................................................... 6
2.
Self-diagnosis Display ..................................................... 6
3.
Service Mode Display ...................................................... 6
3-1. Display Method ................................................................ 6
3-2. Switching of Backup No. ................................................. 6
3-3. End of Display ................................................................. 6
3-2. Switching of Backup No. ................................................. 6
3-3. End of Display ................................................................. 6
4.
Self-diagnosis Code Table ............................................... 7
1. GENERAL
Using this manual ...................................................................... 1-1
Checking supplied accessories .................................................. 1-1
Installing and Charging the battery pack ...................................1-1
Inserting a cassette .....................................................................1-3
Camera recording ...................................................................... 1-3
Hints for better Shooting ...........................................................1-4
Checking the recorded picture ...................................................1-5
Connections for playback .......................................................... 1-5
Playing back a tape .................................................................... 1-6
Using alternative power sources ................................................ 1-7
Changing the mode settings ...................................................... 1-8
Shooting with backlighting .......................................................1-9
Using the FADER function .....................................................1-10
Shooting in the dark (NightShot) ............................................ 1-10
Using the wide mode function .................................................1-11
Using the PROGRAM AE function .........................................1-11
Focusing manually ...................................................................1-12
Enjoying picture effect ............................................................ 1-12
Adjusting the exposure ............................................................ 1-13
Superimposing a title ...............................................................1-13
Making your own titles ............................................................ 1-14
Recording with the date/time ...................................................1-14
Optimizing the recording condition .........................................1-15
Releasing the STEADY SHOT function .................................1-15
Searching the boundaries of recorded date .............................. 1-15
Returning to a pre-registered position .....................................1-16
Locating the marking position .................................................1-16
Writing the RC time code on a recorded tape .........................1-17
Editing onto another tape .........................................................1-18
Charging the lithium battery in the camcoder .........................1-18
Resetting the date and time ...................................................... 1-18
Simple setting of clock by time difference .............................. 1-19
Usable cassettes and playback modes .....................................1-19
Tips for using the battery pack ................................................ 1-20
Maintenance information and precautions .............................. 1-21
Using your camcorder abroad .................................................1-22
Self-diagnosis display .............................................................. 1-22
Identifying the parts .................................................................1-23
Warning Indicators .................................................................. 1-25
Checking supplied accessories .................................................. 1-1
Installing and Charging the battery pack ...................................1-1
Inserting a cassette .....................................................................1-3
Camera recording ...................................................................... 1-3
Hints for better Shooting ...........................................................1-4
Checking the recorded picture ...................................................1-5
Connections for playback .......................................................... 1-5
Playing back a tape .................................................................... 1-6
Using alternative power sources ................................................ 1-7
Changing the mode settings ...................................................... 1-8
Shooting with backlighting .......................................................1-9
Using the FADER function .....................................................1-10
Shooting in the dark (NightShot) ............................................ 1-10
Using the wide mode function .................................................1-11
Using the PROGRAM AE function .........................................1-11
Focusing manually ...................................................................1-12
Enjoying picture effect ............................................................ 1-12
Adjusting the exposure ............................................................ 1-13
Superimposing a title ...............................................................1-13
Making your own titles ............................................................ 1-14
Recording with the date/time ...................................................1-14
Optimizing the recording condition .........................................1-15
Releasing the STEADY SHOT function .................................1-15
Searching the boundaries of recorded date .............................. 1-15
Returning to a pre-registered position .....................................1-16
Locating the marking position .................................................1-16
Writing the RC time code on a recorded tape .........................1-17
Editing onto another tape .........................................................1-18
Charging the lithium battery in the camcoder .........................1-18
Resetting the date and time ...................................................... 1-18
Simple setting of clock by time difference .............................. 1-19
Usable cassettes and playback modes .....................................1-19
Tips for using the battery pack ................................................ 1-20
Maintenance information and precautions .............................. 1-21
Using your camcorder abroad .................................................1-22
Self-diagnosis display .............................................................. 1-22
Identifying the parts .................................................................1-23
Warning Indicators .................................................................. 1-25
TABLE OF CONTENTS
2. DISASSEMBLY
2-1. Removal of Front Panel Block ......................................... 2-1
2-2. Removal of Cabinet (R) Block ......................................... 2-2
2-3. Removal of EVF Block-1 ................................................. 2-2
2-4. Removal of TR Cover, CF-49 Board and LCD Block ..... 2-2
2-5. Removal of EVF Block-2
2-2. Removal of Cabinet (R) Block ......................................... 2-2
2-3. Removal of EVF Block-1 ................................................. 2-2
2-4. Removal of TR Cover, CF-49 Board and LCD Block ..... 2-2
2-5. Removal of EVF Block-2
(LB-54, VF-119 and VF-120 Boards) .............................. 2-3
2-6. Removal of EVF Block-3 (VF-99 Board) ........................ 2-3
2-7. Removal of Battery Panel Block ...................................... 2-4
2-8. Removal of Cassette Lid Assembly ................................. 2-4
2-9. Removal of Cabinet (L) Block ......................................... 2-4
2-10. Removal of Control Switch Block (FK-8500) ................. 2-4
2-11. Removal of Zoom Lens Block ......................................... 2-5
2-12. Removal of DD-105 and PJ-81 Boards ............................ 2-5
2-13. Removal of VC-195 and SE-65 Boards ........................... 2-5
2-14. Service Position ............................................................... 2-6
2-15. Circuit Boards Location ................................................... 2-7
2-7. Removal of Battery Panel Block ...................................... 2-4
2-8. Removal of Cassette Lid Assembly ................................. 2-4
2-9. Removal of Cabinet (L) Block ......................................... 2-4
2-10. Removal of Control Switch Block (FK-8500) ................. 2-4
2-11. Removal of Zoom Lens Block ......................................... 2-5
2-12. Removal of DD-105 and PJ-81 Boards ............................ 2-5
2-13. Removal of VC-195 and SE-65 Boards ........................... 2-5
2-14. Service Position ............................................................... 2-6
2-15. Circuit Boards Location ................................................... 2-7
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram .................................................... 3-1
3-2. Camera/Video Block Diagram ......................................... 3-5
3-3. VTR/Camera Control Block Diagram ............................. 3-9
3-4. Servo Block Diagram ..................................................... 3-12
3-5. Mode Control Block Diagram ........................................ 3-15
3-6. Audio Block Diagram .................................................... 3-19
3-7. Color EVF Block Diagram ............................................ 3-23
3-8. B/W EVF Block Diagram .............................................. 3-27
3-9. Power Block Diagram .................................................... 3-29
3-2. Camera/Video Block Diagram ......................................... 3-5
3-3. VTR/Camera Control Block Diagram ............................. 3-9
3-4. Servo Block Diagram ..................................................... 3-12
3-5. Mode Control Block Diagram ........................................ 3-15
3-6. Audio Block Diagram .................................................... 3-19
3-7. Color EVF Block Diagram ............................................ 3-23
3-8. B/W EVF Block Diagram .............................................. 3-27
3-9. Power Block Diagram .................................................... 3-29
4. PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS
4-1. Frame Schematic Diagram ................................................. 4-1
4-2. Printed Wiring Boards and Schematic Diagrams ............... 4-6
4-2. Printed Wiring Boards and Schematic Diagrams ............... 4-6
• CD-181 (CCD Imager) Board ......................................... 4-7
• SE-65 (Steady Shot) Board ............................................. 4-9
• VC-195 (Camera, Y/C Processor, IN/OUT,
• SE-65 (Steady Shot) Board ............................................. 4-9
• VC-195 (Camera, Y/C Processor, IN/OUT,
REC/PB Head Amp, Servo/System Control, Servo,
Audio, Mode Control) Board ........................................ 4-13
Audio, Mode Control) Board ........................................ 4-13
• VC-195 (Camera 1) Board ............................................ 4-18
• VC-195 (Camera 2) Board ............................................ 4-21
• VC-195 (Y/C Processor) Board .................................... 4-25
• VC-195 (IN/OUT) Board .............................................. 4-29
• VC-195 (REC/PB Head Amp) Board ............................ 4-33
• VC-195 (Servo/System Control) Board ........................ 4-37
• VC-195 (Servo) Board .................................................. 4-40
• VC-195 (Audio) Board .................................................. 4-43
• VC-195 (Mode Control) Board ..................................... 4-47
• PJ-81 (AV IN/OUT) Board ............................................ 4-51
• Control Switch Block (FK-8500/SS-8500) ................... 4-54
• MA-311 (Stereo Mic, Laser Link) Board ...................... 4-55
• CF-49 (Control) Board .................................................. 4-60
• VF-99 (B/W EVF (B/W EVF Model)) Board ............... 4-68
• VF-119 (Color EVF (Color EVF Model)) Board .......... 4-71
• VF-120 (Color EVF (Color EVF Model)) Board .......... 4-76
• LB-54 (Back Light) Board ............................................ 4-76
• DD-105 (Power) Board ................................................. 4-82
• VC-195 (Camera 2) Board ............................................ 4-21
• VC-195 (Y/C Processor) Board .................................... 4-25
• VC-195 (IN/OUT) Board .............................................. 4-29
• VC-195 (REC/PB Head Amp) Board ............................ 4-33
• VC-195 (Servo/System Control) Board ........................ 4-37
• VC-195 (Servo) Board .................................................. 4-40
• VC-195 (Audio) Board .................................................. 4-43
• VC-195 (Mode Control) Board ..................................... 4-47
• PJ-81 (AV IN/OUT) Board ............................................ 4-51
• Control Switch Block (FK-8500/SS-8500) ................... 4-54
• MA-311 (Stereo Mic, Laser Link) Board ...................... 4-55
• CF-49 (Control) Board .................................................. 4-60
• VF-99 (B/W EVF (B/W EVF Model)) Board ............... 4-68
• VF-119 (Color EVF (Color EVF Model)) Board .......... 4-71
• VF-120 (Color EVF (Color EVF Model)) Board .......... 4-76
• LB-54 (Back Light) Board ............................................ 4-76
• DD-105 (Power) Board ................................................. 4-82
Click on the first or last page to see other CCD-TR311 / CCD-TR311E / CCD-TR411E / CCD-TR412E / CCD-TR511E / CCD-TR512E / CCD-TR640E / CCD-TR730E / CCD-TR840E / CCD-TR845E service manuals if exist.