DOWNLOAD Sony CCD-CR1 / CCD-CR1E (serv.man2) Service Manual ↓ Size: 14.39 MB | Pages: 112 in PDF or view online for FREE

5-2

Fig. 5-1-2.

Front of the lens

Approx.
90 cm

Pattern box

 For details of how remove the cabinet and boards, refer to “2.

DISASSEMBLY”.

When performing only the adjustments, the lens block and boards
need not be disassembled.

The video cartridge need not be installed.

1)

Connect the equipment for adjustments according to Fig. 5-1-
4.

2)

Connect the adjustment remote commander to VC-205 board
CN152 via CPC 11 jig (J-6082-425-A). (See Fig. 5-1-3.) To
operate the adjustment remote commander, connect the DC
input lands of CPC 11 jig to the DC power supply (6.0 to
7.2Vdc).

Setting the “Forced Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 03, and press the PAUSE

button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the operation switch block removed (Don’t disconnect
the adjustment remote commander). After completing
adjustments, be sure to exit the “Forced Power ON Mode”.

Exiting the “Forced Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

Fig. 5-1-3.

CPC 11 jig
(J-6082-425-A) 

Remove the cover.

Conductor side

5-3

Fig. 5-1-4.

Lens block

LANC
jack

DC input lands

CPC 11 jig
(J-6082-425-A)

CD-191
BOARD

CN952

CN501

CN301

CN151

CN152

CN101

CN601

J391

AUDIO VIDEO jack

MJ-88
BOARD

CN701

Adjustment
remote
commander

Regulated power supply
for the adjustment remote commander

(6.0

‘

7.2Vdc)

PD-99
BOARD

CN5601

LCD

CN401

CN801

VC-205
BOARD

VIDEO
CARTRIDGE

Extension board
(J-6082-426-A)

AUDIO OUT

(White)

(Red)

AUDIO IN

VIDEO OUT
(Yellow)

Vector scope

Color moniter

Tarminated
at 75

Ω

Battery
holder

FP-685

When the AC power adaptor is used.

Red

Power cord jig
(J-6082-415-A)

Black

Regulated power
supply (3Vdc)

When a regulated power
supply is used.

AC power
adaptor
(4.2Vdc)

Operation switch block

5-4

Unless otherwise specified, set the switches as follows.
1.

BACK LIGHT (FK block) ............................................... OFF

2.

MACRO (FK block) ........................................................ OFF

Adjust in the given order.

H

A=B

A B

B A

Enlargement

V

0 

±

 0.1msec

Electronic beam scanning frame

CRT picture frame

B

A

Difference in level

Y

ello

w

Cy

an

Green

White

Magenta

Red

Blue

Y

ello

w

Cy

an

Green

White

Magenta

Red

Blue

Fig. a

(Video output terminal

output waveform)

Fig. b (TV monitor picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.

Fig. 5-1-5.

1)

Color bar chart (Standard picture frame).
Adjust the picture frame as shown in Fig. 5-1-5. If adjustments
are performed using the color bar chart. (Standard picture frame)

2)

White pattern (Standard picture frame)
Remove the color bar chart from the pattern box, and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)

5-5

Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F
Page Data”.)
Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F
Page Data”.)

If “Initializing the D,E,F Page Data” is performed, all data of the
D page, E page and F page will be initialized. (It is impossible to
initialize a single page.)

If the D,E,F page data has been initialized, “Modification of D, E,
F Page Data” and all adjustments need to be performed again.

Adjusting page

D

Adjusting Address

00 to 6F

Adjusting page

F

Adjusting Address

00 to FF

Adjusting page

E

Adjusting Address

00 to FF

Initializing Method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 00, and set data: 55 (NTSC) or data:
51 (PAL).

3)

Select page: 2, address: 01, set data: 55 (NTSC) or data: 51
(PAL), and press the PAUSE button of the adjustment remote
commander.

4)

Select page: 2, address: 02, and check that the data is “01”.

5)

Select page: 3, address: 00, and set data: 29.

6)

Select page: 3, address: 01, set data: 29, and press the PAUSE
button of the adjustment remote commander.

7)

Select page: 0, address: 01, and set data: 00.

8)

Perform “Modification of D,E,F Page Data”.

If the D, E, F page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.

Modifying Method:
1)

Before changing the data, select page: 0, address: 01, and set
data: 01.

2)

New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.

If copy the data built in the different model, the camcorder
may not operate.

3)

When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.

4)

Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.

5)

After changing the data, select page: 0, address: 01, and set
data: 00. Also perform all adjustments.

PAL

00

00

71

7D

83

89

Test mode

Fixed data-1

(Initialized data)

Fixed data-2

(Modified data, copy the data built

in the same model.)

Fixed data-1

(Initialized data)

Dry battery down data check

Fixed data-1

(Initialized data)

NTSC

00

00

71

7D

83

89

00 to 0F

10

11

12

13

14

15

16

17

18

19

1A

1B

1C

1D

1E

1F

20

21

22

23

24

25

26

27

28

29

2A

2B

2C

2D

2E

2F

30

31

32

33

34

35

36

37

38

39

3A

3B

3C

3D