Sony SDM-S71R Service Manual ▷ View online
SDM-S71R(E)
1-4
1-4.A BOARD
1 Two screws
(
(
+PTT 3x4)
1 Three screws
(
(
+PTT 3x4)
4 Two screws
(
(
+PTT 3x4)
1 Two screws
(
(
+PTT 3x4)
1 Screw
(
(
+PTT 3x4)
4 Two screws
(
(
+PTT 3x4)
2 Rear shield
3 J710
5 A board
3 J705
3 J702
4Two connector screws
SDM-S71R(E)
1-5
1-5.TFT PANEL
3 Two screws
(+FTT 3x5)
(+FTT 3x5)
1 Two screws
(+BVTP 3x16)
(+BVTP 3x16)
3 Two screws
(+FTT 3
(+FTT 3
x5)
4 TFT panel
2 Bezel assembly
SDM-S71R(E)
2-1
SECTION 2
ADJUSTMENTS
2-1. FUNCTIONAL ADJUSTMENT
•How to go to service mode.
1. On the stand-by mode, press “ 1 “ key while pressing “
r “ key. The monitor goes into service mode.
2. Press “MENU” key.
3. Once press “ “key and select the mark “S” on the second page.
4. Press “OK” key to go to “MAINTAIN” (service menu).
5. Select one of features.
6. Press “MENU” key to exit service mode.
7. Turn power off then on again, the monitor goes to normal mode.
3. Once press “ “key and select the mark “S” on the second page.
4. Press “OK” key to go to “MAINTAIN” (service menu).
5. Select one of features.
6. Press “MENU” key to exit service mode.
7. Turn power off then on again, the monitor goes to normal mode.
If you would like to set the monitor to service mode again,
repeat the above procedure.
repeat the above procedure.
Note:
If the TFT panel or A board is replaced, be sure to perform
the W/B adjustment again.
Before the W/B adjustment, the no signal aging is needed for
30 minutes or more.
If the TFT panel or A board is replaced, be sure to perform
the W/B adjustment again.
Before the W/B adjustment, the no signal aging is needed for
30 minutes or more.
Other Information:
All Mode Recall: On the stand-by mode, press “ 1 “ key while pressing “OK” key. Clears user’s memory, resets BACKLIGHT,CONTRAST, BRIGHTNESS, PHASE,
PITCH, CENTER, COLOR, USER ADJUSTMENT COLOR GAMMA, MENU POSITION, POWERSAVE, LANGUAGE, MENU LOCK to default values. Also clears Aging
Mode.After executing this command, be sure to put AC power cord out and in to set the default values. (Refleshing is required.)
Aging mode: On the stand-by mode, press “ 1 “ key while pressing “
PITCH, CENTER, COLOR, USER ADJUSTMENT COLOR GAMMA, MENU POSITION, POWERSAVE, LANGUAGE, MENU LOCK to default values. Also clears Aging
Mode.After executing this command, be sure to put AC power cord out and in to set the default values. (Refleshing is required.)
Aging mode: On the stand-by mode, press “ 1 “ key while pressing “
R “key. The monitor goes into the no signal aging mode.
To release the aging mode setting, turn off the aging bit in service mode or execute All Mode Recall.
Clear ETI: On the stand-by mode, press “ 1 “ key while pressing “
8
“ key. The monitor information data during EDID is copied to the microcomputer and clears ETI to
zero.
ETI ZERO CLEAR
AGING
INITIAL CLEAR for EEPROM
ANALOG
COLOR TEMP
INITIAL EEPROM
CLEAR ETI
WHITE BALANCE
DEFAULT TIMMING
9300K R
6500K G
RETURN
B
SUB-BRIGHTNESS
R
G
B
SUB-CONTRAST
R
G
B
RETURN
AGING ON
OFF (Default)
OFF (Default)
RETURN
DEFAULT TIMMING
1152 * 864 (Default)
1152 * 870
RETURN
1152 * 864 (Default)
1152 * 870
RETURN
SDM-S81R only
SDM-S51R(E)
2-2
2-2. TIMING SPECIFICATION
VESA 60Hz
YES
P/P
NO
NO
NO
TTL
V
0.700
Vp-p
0
V
NON INT
mm
mm
mm
20
X 16
64
X 64
35IRE
Adj Signal
MODE FOR CUSTOMER
VESA 60Hz
RESOLUTION
1280
1024
X
CLOCK
108.000
MHZ
-- HORIZONTAL --
H-FREQ
63.981
kHz
usec
dots
H. TOTAL
15.630
1688
H. BLK
3.778
408
H. FP
0.444
48
H. SYNC
1.037
112
H. BP
2.296
248
H. ACTIV
11.852
1280
-- VERTICAL --
60.020
Hz
msec
lines
V. TOTAL
16.661
1066
V. BLK
0.656
42
V. FP
0.016
1
V. SYNC
0.047
3
V. BP
0.594
38
V. ACTIV
16.005
1024
1280
1024
X
108.000
MHZ
63.981
kHz
usec
dots
15.630
1688
3.778
408
0.444
48
1.037
112
2.296
248
11.852
1280
60.020
Hz
msec
lines
16.661
1066
0.656
42
0.016
1
0.047
3
0.594
38
16.005
1024
- - S Y N C - -
INT(G)
EXT(H/V)/POLARITY
YES
P/P
EXT(CS) /POLARITY
Serration
NO
NO
NO
SYNC LEVEL
TTL
V
-- VIDEO --
VIDEO LEVEL
0.730
Vp-p
SET UP
0
V
-- OTHERS --
INT/NON INT
NON INT
SIZE(15")
338 X 270
357 X 286
mm
mm
mm
SIZE(17")
-
338 X 270
357 X 286
-
SIZE(18")
#OF GRIDS
20
X 16
DOTS & LINES/GRID
64
X 64
EDID DATA
COMMENTS
- SONY SG SETTING
-OTHERS 100IRE
Adj Signal
V. FREQ(HZ)
Click on the first or last page to see other SDM-S71R service manuals if exist.