Sony CPD-E215E / CPD-E220 / CPD-E220E (serv.man6) Service Manual ▷ View online
CPD-E220/E215E/E220E
GND
GND
Connector
(2P)
(2P)
GND
CN2
CN602
CN310
CN303
CN304
CN307
CN309
CN301
CN302
CN903
Screw
(+BVTT 3 x 8 )
(+BVTT 3 x 8 )
I/O cable assembly
1
Screw
(+M 4 x 8)
(+M 4 x 8)
4
Cable
Cable cover
5
6
2
8
3
Three screws
(+BVTT 3 x 12)
9
A board
7
D board
Cable stopper
Cable holder
12
Four screws
(+BVTT 3 x 8)
(+BVTT 3 x 8)
10
GND
2
Two claws
1
Two screws
(+BVTP 4 x 16)
(+BVTP 4 x 16)
3
Cabinet
Bezel assembly
Bezel assembly
Cabinet
Cabinet
Push in the tip of a screwdriver
about 10mm to unlock the claw.
about 10mm to unlock the claw.
SECTION 2
DISASSEMBLY
2-1. CABINET REMOVAL
2-2. A AND D BOARDS REMOVAL
2-1
CPD-E220/E215E/E220E
A board
1
3
2
Tention spring
GND
GND
CN602
CN903
Connector
(2P)
(2P)
CN2
CN307
Anode cap
(See page 2-3.)
(See page 2-3.)
Neck assembly
Degauss coil
Deflection yoke
1
Two degauss
coil holder
coil holder
Two degauss
coil holder
coil holder
13
Cussion
Picture tube
7
Bezel assembly
12
Two screws
(+BVTT 4 x 8)
(+BVTT 4 x 8)
Four screws
(Hexagon)
(Hexagon)
4
Two screws
(+BVTP 4 x 16)
(+BVTP 4 x 16)
3
Chassis assembly
5
A board
2
8
10
11
9
6
2-4. PICTURE TUBE REMOVAL
2-2
2-3. SERVICE POSITION
CPD-E220/E215E/E220E
2-3
2-5. H BOARD REMOVAL
3
When one side of the rubber cap is
separated from the anode button, the
anode-cap can be removed by turning
up the rubber cap and pulling up it in the
direction of the arrow
separated from the anode button, the
anode-cap can be removed by turning
up the rubber cap and pulling up it in the
direction of the arrow
C
.
•
HOW TO HANDLE AN ANODE-CAP
1
Don’t scratch the surface of anode-caps with sharp shaped
material!
material!
2
Don’t press the rubber hardly not to damage inside of anode-
caps!
A material fitting called as shatter-hook terminal is built in the
rubber.
caps!
A material fitting called as shatter-hook terminal is built in the
rubber.
3
Don’t turn the foot of rubber over hardly!
The shatter-hook terminal will stick out or damage the rubber.
The shatter-hook terminal will stick out or damage the rubber.
•
REMOVAL OF ANODE-CAP
NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after
removing the anode.
•
REMOVING PROCEDURES
1
Turn up one side of the rubber cap in
the direction indicated by the arrow
the direction indicated by the arrow
A
.
2
Using a thumb pull up the rubber cap
firmly in the direction indicated by the
arrow
firmly in the direction indicated by the
arrow
B
.
a
b
c
Anode Button
H board
H bracket
4
Menu button
Cussion
Bezel assembly
Picture tube
5
Claw
3
Screw
(+BVTP 4 x 16)
(+BVTP 4 x 16)
1
2
CPD-E220/E215E/E220E
2-6. HARNESS LOCATION
CN903
CN902
CN501
CN603
CN505
CN901
CN502
CN310
CN301
CN307
CN309
CN302
CN304
CN303
CN504
CN602
CN2
CN1
Picture tube
Degauss coil
A board
AC inlet
D board
H board
2-4
Click on the first or last page to see other CPD-E215E / CPD-E220 / CPD-E220E (serv.man6) service manuals if exist.