Sony DVP-S533D Service Manual ▷ View online
6-7
4.
SACD
Select
[4]
, insert SACD disc, and press
[ENTER]
key, and the
adjustment will be made through the following steps, then adjusted
values will be written to the EEPROM. However, if SACD disc is
not available, use the player with initial data, skipping the SACD
adjustment. In this case, you can finish the adjustment if pressing
the
values will be written to the EEPROM. However, if SACD disc is
not available, use the player with initial data, skipping the SACD
adjustment. In this case, you can finish the adjustment if pressing
the
[STOP]
button.
SACD Adjustment Steps
1. Sled Tilt Reset
2. Set Disc Type CD
3. LD ON
4. Spdl Start
5. Wait 500 msec
6. Focus Servo ON 0
7. Auto track Offset Adjust
8.
9. CLVA ON
10. Wait 500 msec
11. Tracking ON
12. Wait 1 sec
13. Sled ON
14. Check CLV ON
15. Auto Focus Offset Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto LFO Adjust
22. Auto Track Gain Adjust
1. Sled Tilt Reset
2. Set Disc Type CD
3. LD ON
4. Spdl Start
5. Wait 500 msec
6. Focus Servo ON 0
7. Auto track Offset Adjust
8.
9. CLVA ON
10. Wait 500 msec
11. Tracking ON
12. Wait 1 sec
13. Sled ON
14. Check CLV ON
15. Auto Focus Offset Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto LFO Adjust
22. Auto Track Gain Adjust
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev
27. All Servo Stop
6-5.
DRIVE MANUAL OPERATION
On the Test Mode Menu screen, select
[2]
, and the manual opera-
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
0. Disc Check Memory
Exit: Return
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
2. After power ON, if the Drive Manual Operation was se-
lected, first perform “Reset SLED TILT” by opening 1.
Disc Type screen.
Disc Type screen.
3. In case of an alarm, immediately press the
[STOP]
but-
ton to stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote com-
mander)
mander)
[POWER]
Power OFF
[STOP]
Servo stop
[OPEN/CLOSE]
Stop+Eject/Loading
[RETURN]
Return to Operation Menu or Test Mode
Menu
Menu
[NEXT]
,
[PREV]
Transition between sub modes of menu
[1]
to
[9]
,
[0]
Selection of menu items
Cursor UP/DOWN
Increase/Decrease in manually adjusted
value
value
6-8
0.
Disc Check Memory
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press
is written to the EEPROM. First load DVD SL disc and press
[1]
,
next load CD disc and press
[2]
, and finally load DVD DL disc
and press
[3]
.
The adjustment must be executed more than once after default
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by pressing
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by pressing
[NEXT]
or
[PREV]
key, but you cannot enter this mode from another mode.
You can enter this mode from the Operation Menu screen only.
1.
Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
EMG. 00
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
[1]
automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
TC. : : EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
tion.
[1]
Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2]
to
[9]
Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
value is written to the address of se-
lected disc. No further entry is neces-
sary if
[1]
was selected.
2. Servo Control
Servo Control
1. LD
Off R.Sled FWD
2. SP
Off L.Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
6-9
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
tion.
[1]
LD
Turn ON/OFF the laser.
[2]
SP
Turn ON/OFF the spindle.
[3]
Focus
Search the focus and turn on the focus.
[4]
TRK
Turn ON/OFF the tracking servo.
[5]
Sled
Turn ON/OFF the sled servo.
[6]
CLVA
Turn ON/OFF normal servo of spindle
servo.
servo.
[7]
FCS. Srch
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
search to the focus drive to check the
focus drive system.
→
Sled FWD
Move the sled outward. Perform this
operation with the tracking servo turned
off.
off.
←
Sled REV
Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
eration with the tracking servo turned
off.
↑
Tilt UP
Move the tilt upward.
↓
Tilt DOWN
Move the tilt downward.
The following menus are normally not used.
3.
Track/Layer Jump
4.
Manual Adjustment
5.
Auto Adjustment
The persons who do not know well about these menus should not
use them.
use them.
6. Memory Check
EEPROM DATA
CD
– DVD –
ID No. 00
SACD
SL
L0
L1
Focus Gain
xx xx
xx
xx
xx
TRK. Gain
xx xx
xx
xx
xx
Focus Offset
xx xx
xx
xx
xx
TRK. Offset
xx xx
xx
xx
xx
L. F. Offset
xx xx
xx
xx
xx
EQ Boost
xx xx
xx
xx
xx
Jitter
xx xx
xx
xx
xx
Mirror Time
xx xx
xx
xx
xx
_
CLEAR: Default Set
This screen displays current servo adjusted data stored in the
EEPROM. Though adjusted data can be initialized with the
EEPROM. Though adjusted data can be initialized with the
[CLEAR]
key, they cannot be restored after initialization.
So, before clearing, make a note of the adjusted data.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable dis-
connection, then perform adjustment again.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable dis-
connection, then perform adjustment again.
6-6. MECHA AGING
### Mecha Aging ###
Press OPEN key
Abort: STOP key
On the Test Mode Menu screen, selecting
[3]
executes the aging
of mechanism. First, open the tray and load a disc. Press the
[PLAY]
key, and the aging will start. When the tray is closed, the disc type
and size are judged and displayed. During aging, the repeat cycle
is displayed. Aging can be aborted at any time by pressing the
and size are judged and displayed. During aging, the repeat cycle
is displayed. Aging can be aborted at any time by pressing the
[STOP]
key. After the operation has stopped, unload the disc and
press again the
[STOP]
key or the
[RETURN]
key to return to the
Test Mode Menu.
6-7. EMERGENCY HISTORY
### MEG. History ###
Laser Hours
CD
xxxxxxxh
DVD
xxxxxxxh
1. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
2. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
Select: 1 – 9
Scroll: UP/DOWN
(1: Last EMG.)
Exit: Return
On the Test Mode Menu screen, selecting
[4]
displays the infor-
mation such as servo emergency history. The history information
from last 1 up to 10 can be scrolled with
from last 1 up to 10 can be scrolled with
↑
key or
↓
key. Also,
specific information can be displayed by directly entering that
number with ten keys.
number with ten keys.
The upper two lines display the laser ON total hours. Data below
minutes are omitted.
minutes are omitted.
Clearing History Information
Clearing laser hours
Press
Press
[DISPLAY]
and
[CLEAR]
keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press
Clearing emergency history
Press
[TITLE]
and
[CLEAR]
keys in this order.
Initializing set up data
Press
Press
[DVD]
and
[CLEAR]
keys in this order.
The data have been initialized when “Set Up Initialized” mes-
sage is displayed. The EMG. History screen will be restored
soon.
sage is displayed. The EMG. History screen will be restored
soon.
6-10
How to see Emergency History
1 : Emergency Code
2 : Don’t Care
2 : Don’t Care
These codes are used for verification of software designing.
3 : Historical order 1 to 9
Emergency Codes List
10: Communication to IC001 (TK-51 board) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Communication to EEPROM, IC201 (MB-85 board) failed.
13: Writing of hours meter data to EEPROM, IC201 (MB-85
11: Each servo for focus, tracking, and spindle is unlocked.
12: Communication to EEPROM, IC201 (MB-85 board) failed.
13: Writing of hours meter data to EEPROM, IC201 (MB-85
board) failed.
14: Communication to Servo DSP IC701 (MB-85 board) failed,
or Servo DSP is faulty.
20: Initialization of tilt servo and sled servo failed. They are not
placed in the initial position.
21: Tilt servo operation error
22: Syscon made a request to move the tilt servo to wrong posi-
22: Syscon made a request to move the tilt servo to wrong posi-
tion.
23: Sled servo operation error
24: Syscon made a request to move the sled servo to wrong posi-
24: Syscon made a request to move the sled servo to wrong posi-
tion.
30: Tracking balance adjustment error
31: Tracking gain adjustment error
32: Focus balance adjustment error
33: Focus bias adjustment error
34: Focus gain adjustment error
35: Tilt servo adjustment error
36: RF equalizer adjustment error
37: RF group delay adjustment error
38: Jitter value after adaptive servo operation is too large.
40: Focus servo does not operate.
41: With a dual layer (DL) disc, focus jump failed.50: CLV
31: Tracking gain adjustment error
32: Focus balance adjustment error
33: Focus bias adjustment error
34: Focus gain adjustment error
35: Tilt servo adjustment error
36: RF equalizer adjustment error
37: RF group delay adjustment error
38: Jitter value after adaptive servo operation is too large.
40: Focus servo does not operate.
41: With a dual layer (DL) disc, focus jump failed.50: CLV
(spindle) servo does not operate.
51: Spindle does not stop.
60: With a DVD disc, Syscon made a request to seek nonexistent
60: With a DVD disc, Syscon made a request to seek nonexistent
address.
61: With a CD disc, Syscon made a request to seek nonexistent
address.
62: With a CD disc, Syscon made a request to seek nonexistent
track No. and index No.
63: With a DVD disc, seeking of target address failed.
64: With a CD disc, seeking of target address failed.
65: With a CD disc, seeking of target index failed.
70: With a DVD disc, physical information data could not be read.
71: With a CD disc, TOC data could not be read.
80: Disc type judgment failed.
81: As disc type judgment failed, retry was repeated.
82: As disc type judgment failed, a measurement error occurred.
83: Disc type could not be judged within the specified time.
84: Illegal command code was received from Syscon.
85: Illegal command was received from Syscon.
64: With a CD disc, seeking of target address failed.
65: With a CD disc, seeking of target index failed.
70: With a DVD disc, physical information data could not be read.
71: With a CD disc, TOC data could not be read.
80: Disc type judgment failed.
81: As disc type judgment failed, retry was repeated.
82: As disc type judgment failed, a measurement error occurred.
83: Disc type could not be judged within the specified time.
84: Illegal command code was received from Syscon.
85: Illegal command was received from Syscon.
6-8.
VERSION INFORMATION
## Version Information ##
IF con.
Ver. x. xxx (xxxx)
Group 00
SYScon.
Ver. x. xxx (xxxx)
Model xx
Region 0x
SW1 ??
SW2 ??
Exit: RETURN
On the Test Mode Menu screen, selecting
[5]
displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
6-9.
VIDEO LEVEL ADJUSTMENT
On the Test Mode Menu screen, selecting
[6]
displays color bars
for video level adjustment. During display of color bars, OSD dis-
appears but the menu screen will be restored if pressing any key.
appears but the menu screen will be restored if pressing any key.
Measurement point
: LINE OUT VIDEO
(75
Ω
terminating resistance)
Measuring instrument : Oscilloscope
Adjustment device
Adjustment device
: RV401 on MB-85 board
Specified value
: 1.0 ± 0.02 Vpp
3
1.
1
2
2
1.0
±
0.02 Vp-p
6-10 E
Click on the first or last page to see other DVP-S533D service manuals if exist.