Sony DVP-NS47P / DVP-NS508P / DVP-NS57P / DVP-NS608P / DVP-NS64P / DVP-NS67P Service Manual ▷ View online
2-1
DVP-NS47P/NS57P/NS508P/NS64P/NS67P/NS608P
Note: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE
SECTION 2
DISASSEMBLY
2-2. FRONT PANEL ASSEMBLY
4
Two Tapping Screws
6
Upper case
3
Tray Cover
5
Three Tapping Screws
2
Chassis Back
1
4
Claw
1
Claw
2
Claw
3
Claw
5
Front Panel Assembly
2-2
DVP-NS47P/NS57P/NS508P/NS64P/NS67P/NS608P
2-3. LOADING ASSEMBLY
b
a
b
6
Three Screws
+BV3
(3-CR)
7
Loading Assembly
5
PM-136 Harness
(CN201,
10P)
1
FMO-013 Flat Flexible Cable (CN101, 24P)
3
FMS-015 Flat Flexible Cable (CN202, 5P)
4
PM-136 Harness (CN501, 10P)
2
MD-119 Harness (CN201, 6P)
a
2-3
DVP-NS47P/NS57P/NS508P/NS64P/NS67P/NS608P
2-4. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current
or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge Current
or ElectroStatic Discharge (ESD):
After take-out FMO-013 Flat Flexible Cable from CN101 of
MV-57 board immediately ground FMO-013 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
MV-57 board immediately ground FMO-013 Flat Flexible Cable
pattern using short clip. Metal paper clip can be used as short
clip.
5
FMO-013 Flat Flexible Cable (CN101, 24P)
4
MD-119 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-313CAA/C2RP)
2
FFC Holder
Shortland Position
Note:
Solder shortland before remove the
FMO-013 Flat Flexible Cable from
24 pin BU connector.
FMO-013 Flat Flexible Cable from
24 pin BU connector.
The components identified by
mark or dotted line with mark
mark or dotted line with mark
are critical for safety.
Replace only with part number
specified.
specified.
2-4
DVP-NS47P/NS57P/NS508P/NS64P/NS67P/NS608P
2-5. REAR PANEL, MV-57 BOARD and IF-156 BOARD
2
5
FMS-015 Flat Flexible Cable
(CN202,
5P)
6
FMO-008 Flat Flexible Cable
(CN101,
24P)
9
FIM-019 Flat Flexible Cable
(CN401,
23P)
q;
MV-057 Board
4
MD-119 Harness
(CN201,
6P)
7
PM-136 Harness
(CN501,
10P)
8
Three Screws
+BV3
(3-CR)
One Screws
+BV3 (3-CR)
+BV3 (3-CR)
3
Rear Panel
1
Two Screws
qs
IF-156 Board
a
o
qa
Two Screws
+BV3
(3-CR)
o
I
c
c
a
Note:
Caution Point on the PWB IF-156
Caution Point on the PWB IF-156
When handling IF-156 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND402).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND402).
Click on the first or last page to see other DVP-NS47P / DVP-NS508P / DVP-NS57P / DVP-NS608P / DVP-NS64P / DVP-NS67P service manuals if exist.