DOWNLOAD Sony DVP-NC875V Service Manual ↓ Size: 10.66 MB | Pages: 98 in PDF or view online for FREE

5-5

197

DACVSSB

Ground

Ground pin for Video DAC circuitry
Analog composite output

198

CVBS/YUV3

Output

Video data output bit3

199

DACVDDA

Power

3.3V power for Video DAC circuitry
Green or Y

200

YG/YUV4

Output

Video data output bit4

201

DACVSSA

Ground

Ground pin for Video DAC circuitry
Blue or Cb

202

B/Cb/Pb YUV5

Output

Video data output bit5
Red or Cr

203

R/Cr/Pr YUV6

Output

Video data output bit6

204

DVDD3

Power

3.3V power pin for Video DAC digital circuitry

205

VSYN

Output SMT

Vertical sync signal output for ITU-R BT.601

206

YUV7

Output SMT

Video data output bit7

207

HSYN

Output SMT

Horizontal sync signal output for ITU-R BT.601

Output Default

208

SMSCK

High

HDMI  Sub CPU Serial clock

209

SMSDI

Input

HDMI  Sub CPU Serial data input

Output Default

210

SMSDO

High

HDMI  Sub CPU Serial data input

Output Default

211

xSMCS

High

Chip Select signal output to HDMI Sub CPU

212

DVDD3

Power

3.3V power pin for internal digital circuitry

213

ALRCK

Output PD,SMT

Audio left/right channel clock

214

ABCK

Output

Audio Bit Clock output

215

ACLK

Output

Master clock output for Audio DAC

216

DVSS

Ground

Ground pin for internal digital circuitry

217

ASDATA0

Output  PD,SMT

Audio serial data 0 : L/R

218

ASDATA1

Output  PD,SMT

Audio serial data 1 : SL/SR

219

ASDATA2

Output  PD,SMT

Audio serial data 2 : C/SW

Output PD,SMT

220

xRST

Default Low

Reset output signal for ADAC (Low Active)

221

DVDD18

Power

1.8V power pin for intenal digital circuitry

222

ASDATA4

Output  PD,SMT

Audio serial data 4: Down-mixed L/R

223

DVSS

Ground

Ground pin for internal digital circuitry

224

D-WIDE

Input

Video aspect ratio control for D-terminal. (H: 16:9, L: 4:3)

225

SPDIF

Output

SPDIF output

226

RFGND18

Ground

Ground pin for internal analog circuitry

227

RFVDD18

Power

1.8V power pin for internal analog circuitry

228

XTALO

Output

27M crystal output

229

XTALI

Input

27M crystal input

230

JITFO

Analog Output

The output terminal of RF jitter meter

231

JITFN

Analog Input

The input terminal of RF jitter meter

232

PLLVSS

Ground

Ground pin for data PLL and related analog circuitry

233

IDACEXLP

Analog Output

C input

234

PLLVDD3

Power

3.3V power pin for data PLL and related analog circuitry

235

LPFON

Analog Output

The negative output terminal of loop filter amplifier

236

LPFIP

Analog Input

The positive input terminal of loop filter amplifier

237

LPFIN

Analog Input

The negative input of loop filter amplifier

238

LPFOP

Analog Output

The positive output of loop filter amplifier

239

ADCVDD3

Power

Power pin for ADC circuitry

240

S_VCM

Analog Input

SACD Commom mode reference

241

ADCVSS

Ground

Ground pin for ADC circuitry

242

S_VREFP

Analog Input

SACD Top reference

243

S_VREFN

Analog Input

SACD Buttom reference

244

RFVDD3

Power

3.3V power pin for RF digital circuitry

5-6

245

RFRPDC

Analog Output

RF ripple detect output

246

RFRPAC

Analog Input

RF ripple detect input (through AC-coupling)

247

HRFZC

Analog Input

High frequency RF ripple zero crossing

248

CRTPLP

Analog Output

Defect level filter capacitor connecting

249

RFGND

Ground

Ground pin for RF digital circuitry

250

CEQP

Analog Output

EQ offset loop capacitance

251

CEQN

Analog Output

EQ offset loop capacitance

252

OSP

Analog Output

RF  Offset cancellation capacitor connecting

253

OSN

Analog Output

RF  Offset cancellation capacitor connecting

254

RFGC

Analog Output

RF AGC loop capacitor conecting for DVD-ROM

255

IREF

Analog Input

Current reference input

256

AVDD3

Power

3.3V power pin for analog circuirtry

5-6E

6-1

To enter Mirror Time Adjustment, press 5 on the remote
commander. The screen will appear as below.

Mirr time Adjust Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:
3. Threshold:
4. Save to EEPROM
5. Default set MIRR time

[Open] Tray open [Close] Tray close
-

 Return to previous menu

There are five main commands in the Mirr time Adjust menu as
shown in the figure above. The functions of each command are
described in the following page.

This command checks the Mirror time value for CD disc.

This command checks the Mirror time value for DVD disc.

This command displays the threshold value between CD and DVD
mirror time.

This command saves an adjusted mirror time value to the EEPROM.

This command will set CD and DVD mirror time to firmware default
value.

[Open] / [Close]
Pressing the [Open] / [Close] button controls the tray for disc change
during mirror time adjustment.

- Return to previous menu
Press - button to return to previous menu.

In order to execute mirror time adjustment, the following standard
procedures must be followed.

(1)

In standby mode, press 

[TOP MENU]

, 

[CLEAR]

,

[POWER]

 to enter Remocon Diagnosis Mode.

(2)

Select “2. Drive Manual Operation”.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History Check
4. Version information
5. Video Level Adjustment

Model

:  DPX-xxxx_xx

IF-con

: Ver. x.xxx (xxxx)

Syscon

: Ver. x.xxx

The Mirror Time and IOP measurement allows you to make
diagnosis and adjustment simply by using the remote commander
and monitor TV. The instructions, diagnosis results, etc. are given
on the on screen display (OSD).

The Mirror Time and IOP measurement is required is such events
where servicing a DVD-Player includes changing the Base Unit
(BU). For each new BU to be used with a certain MB-117 board,
Mirror Time and IOP measurement need to be carried out.

Press the 

[TOP MENU]

, 

[CLEAR]

, 

[POWER]

 keys on the remote

commander in this order with the DVD player in standby mode.
The Test Mode starts, then the menu shown below will be
displayed on the TV screen.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. Video Level Adjustment

Model Name : DPX-xxxx_xx
IF-con

: Ver. x.xxx (xxxx)

Syscon

: Ver. x.xxx

The menu above is the Remocon Diagnosis Menu screen which
consists of six main function. At the bottom of the menu screen,
the model name and IF-con version. To enter Mirror Time
Adjustment menu, press button 2 on the remote commander to
enter Drive Manual Operation menu. To exit from the Test Mode,
press the power button on the remote commander.

The Drive Manual Operation menu consists of five main
function. By pressing 2 on the remote commander in the
Remocon Diagnosis Menu, the screen will appear as below.

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. Mirr Time Adjust
0. Return to Top Menu

6-2

(3)

Select “5. MIRR time Adjust”.

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu

(4)

Select “5. Default set MIRR time”.

MIRR time adjustment Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:
3. Threshold:
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(5)

Select “3. Threshold”.

(6)

Confirm the number. If it is 75, go to next step. If it is any
other value, return to step 4.

MIRR time adjustment Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:
3. Threshold: 75
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(7)

Push “Open/Close” key to eject tray.

(8)

Insert Test Disc HLX-504 into tray.

(9)

Push “Open/Close” key to close tray.

(10)

Push “2. DVD MIRR time Check”.

(11)

Wait for HEX number to display.

(12)

Confirm the number, if XX is 28 ~ 70, proceed with next
step. If no, return to 8.

MIRR time adjustment Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:  xx  xx
3. Thereshold:
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(13)

Push “4. Save to EEPROM”.

(14)

Confirm the same values are displayed. If it is not same,
return to step 7.

MIRR time adjustment Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:  XX XX
3. Threshold:
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(15)

Push “Open/Close” key to eject tray.

(16)

Take out HLX-504 and insert Test Disc YEDS-18 into
tray.

(17)

Push “Open/Close” key to close tray.

(18)

Push “1. CD MIRR time check”.

(19)

Wait for HEX number to display.

(20)

Confirm the number, if YY is 5A ~ E8, proceed with next
step. If no, return to 15.

MIRR time adjustment Menu

1. CD MIRR time Check:  yy  YY
2. DVD MIRR time Check:  XX  XX
3. Threshold:
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(21)

Push “4. Save to EEPROM”.

(22)

Confirm the same values are displayed. If it is not the
same, return to step 15.

MIRR time adjustment Menu

1. CD MIRR time check:  YY  YY
2. DVD MIRR time check:  XX  XX
3. Threshold:
4. Save to EEPROM:
5. Default set MIRR time:

[Open] Tray open [Close] Tray close
-

 Return to previous menu

(23)

Push “Open/Close” key to eject tray.

(24)

Remove Test Disc YEDS-18  from  tray.

(25)

Push “Open/Close” key to close tray.

(26)

Press “0” to return to the Drive Manual Operation menu.

(27)

Press “0” to return to the Remocon Diagnosis Menu.

(28)

Press power button to switch OFF set.