Sony DVP-NC60P Service Manual ▷ View online
2-3
DVP-NC60P
2-5. FRONT PANEL SECTION
4
MD-109 Harness
(CN201,
6P)
6
FM-100 Harness
(CN404,
11P)
5
PM-120 Harness
(CN501,
10P)
3
FMO-006 Flat Flexible Cable
(CN101,
24P)
7
Table Assembly
Display Filter
1
Four Screws
+BV3 (3CR)
2
PM-120 Harness
(CN201,
10P)
0
Mirror Reflector Assy
8
Cover Tray Assy
9
Screw
+BVT2.6
(3CR)
2-6. TABLE ASS’Y
Note:
If cover tray removed its should be
replaced with new cover tray.
replaced with new cover tray.
Two Screws
+BV3 (3-CR)
+BV3 (3-CR)
3
Front Panel Section
2
FIS-004 Flat Flexible Cable
(CN405,
11P)
IF-127 PWB
Connector
(CN201)
(CN201)
1
Note:
Before remove FMO-006 Flat
Flexible Cable, please follow point
at page 2-6.
Flexible Cable, please follow point
at page 2-6.
2-4
DVP-NC60P
1
FIS-004 Flat Flexible Cable
(CN501,
11P)
7
FM-100 Harness
(CN404,
11P)
Two Screws
+BV3 (3CR)
+BV3 (3CR)
4
Two Screws
+BV3
(3-CR)
6
FIM-008 Flat Flexible Cable
(CN401,
23P)
5
FIM-009 Flat Flexible Cable
(CN403,
5P)
8
FIS-004 Flat Flexible Cable
(CN405,
11P)
9
FLD
3
Table Assy
2
Front Panel
0
IF-127 Board
2-7. IF-127 BOARD
Note:
Caution Point on the PWB IF-127
When handling IF-127 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
2-5
DVP-NC60P
Loading Motor Assembly
(M901)
(M901)
Table
Belt (Timing)
Screw
(M2.6x4) (3CR)
(M2.6x4) (3CR)
Screw
(M2.6x4) (3CR)
(M2.6x4) (3CR)
Claws
Claw
MD-105 Board
ML-066 Harness
(CN004, 2P)
(CN004, 2P)
2-8. LOADING MOTOR ASS’Y
2-6
DVP-NC60P
2-9. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-310CAB/C2
RP)
4
FMO-006 Flat Flexible Cable
(24P)
5
Optical Pick-Up
2
Four Insulator Screws
3
MD-109 Harness
1
BU Holder
(6P)
Note:
Solder short land before
remove the harness from
24 pin BU connector.
remove the harness from
24 pin BU connector.
Shortland Position
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
After take-out FMO-006 Flexible cable from CN101 of
MV-045 board immediately ground FMO-006 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
MV-045 board immediately ground FMO-006 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
Click on the first or last page to see other DVP-NC60P service manuals if exist.