Sony DVP-F41MS Service Manual ▷ View online
2-1
2-2. UPPER CASE
2-3. MECHANISM DECK
2-4. CHUCKING ARM BLOCK
DVP-F41MS
Note : Follow the disassembly procedure in the numerical order
given.
2-1. TERMINAL COVER, LOWER CASE
SECTION 2
DISASSEMBLY
2
While opening claw in the arrow
direction, and remove chucking
arm assembly.
arm assembly.
1
Tension spring
2
Claw
1
Claw
3
Claw
4
Claw
5
Remove case (upper) in
the arrow direction.
1
Ground
plate (rear)
2
Ground plate
(side)
3
Flexible boards
(3 pcs)
(CN201, 202, 402)
(CN201, 202, 402)
4
Screws
(B3) (2 pcs)
5
Screw (B3)
6
Mechanism deck
1
Remove terminal
cover in the arrow
direction.
direction.
Insert the small type flat-blade
screwdriver into the groove, and
lift up rubber foot.
screwdriver into the groove, and
lift up rubber foot.
3
Screws (2 pcs)
2
Feet (2 pcs)
4
Screws
(3 pcs)
5
Remove case (lower) in
the arrow direction.
2-2
2-5. MD-90, BOARD, LEVER ASSEMBLY
2-6. BASE (C) ASSEMBLY
2-7. OPTICAL DEVICE
2-8. BU HOLDER
1
Tension spring
2
While pushing
claw in the arrow
direction, and remove
lever assembly.
direction, and remove
lever assembly.
3
Remove lever assembly.
4
Flexible
board
(CN301)
(CN301)
5
Screws
(B2.6) (2 pcs)
6
MD-90
board
1
Flexible
board
(CN102)
(CN102)
2
Flexible
board
(CN103)
(CN103)
3
Screws
(2 pcs)
4
Screws (2 pcs)
5
Base (C) assembly
3
1
3
1
1
Insulator screw
2
Remove optical
device in the arrow
direction.
direction.
3
Insulator
1
1
1
Screws (PWH 2.6) (3 pcs)
2
BU holder
3
Rack (L)
4
Tension spring
2-3
2-9. GATE ASSEMBLY, COVER (T)
2-10. ROLLER (SLIDER)
2-11. SLIDER (L), SLIDER (R)
2-12. FL-123A BOARD
1
Screws (2 pcs)
2
Gate assembly
3
While opening two claws
on the base in the arrow
directions, and remove cover (T).
directions, and remove cover (T).
4
Compression spring
1
2
2
1
2
2
1
2
2
1
Stopper washers
(4 pcs)
2
Rollers (slider)
(4 pcs)
2
Move slider (L) in the arrow
direction, and remove it.
1
Move slider (R) in the arrow
direction, and remove it.
5
FL-123 board
4
Screws
(B3) (2 pcs)
1
FL cover
2
Flexible board
(CN403)
3
Flexible board (CN404)
2-4
2-13. MB-99A, IR-39A BOARDS
2-14. Sliders (L) and (R) Phase Adjustment
When installing the gear (P), the phase
adjustment between sliders (L) and (R)
is performed in the following position.
adjustment between sliders (L) and (R)
is performed in the following position.
1
Gear (P)
Slider (R)
Slider (L)
4
Screws
(B3) (5 pcs)
2
Screws (B3) (3 pcs)
3
IR-39 board
5
Screws (B3) (4 pcs)
6
Screws
(B3) (3 pcs)
8
MB-99 board
1
Flexible board (CN404)
7
Hold Down board(DC)
Click on the first or last page to see other DVP-F41MS service manuals if exist.