DOWNLOAD Sony DVP-CX995V Service Manual ↓ Size: 8.44 MB | Pages: 116 in PDF or view online for FREE

25

20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. Focus Jump (L0 t L1)
25. Tracking Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off

Result

disc type : DL L0

An.Off.AB xx xx  TE levDVD xx

An.Off.CD xx xx  TE levCD  --

An.Off.EF -- --  TE Offset xx

An.G.Main xx     FCS Gain  xx

An.G.Side --     TRK Gain  xx

RF level  xx     FCS Bal.  -- xx

FE S L0,1 xx --  REFQ      -- xx

VTS2      --     Jitter    xx

1:L1 Page

Exit:RETURN

Result

disc type : DL L1

An.Off.AB -- --  TE levDVD xx

An.Off.CD -- --  TE levCD  --

An.Off.EF -- --  TE Offset xx

An.G.Main xx     FCS Gain  xx

An.G.Side --     TRK Gain  xx

RF level  xx     FCS Bal.  -- xx

FE S L0,1 -- xx  REFQ      -- xx

VTS2      --     Jitter    --

0:L0 Page

Exit:RETURN

Select [4] and press the [ENTER] key. Then, [1] DVD-SL disc, [2]
CD disc, and [5] DVD-DL (Opposite) disc are adjusted in this order.
Because the changer model can accept multiple discs in advance of
adjustment, adjustments can be continued by exchanging discs
automatically whenever an adjustment is completed following the
instruction on screen. You can exit the adjustment by pressing
the

x

button. In adjusting each disc, the mirror time is measured

to check the disc type. In the auto adjustment, whether the disc type
is correct is not checked unlike conventional models, and
accordingly, take care not to insert a different type of disc.

Three kinds of discs can be set in advance. In this case, set discs in
order to the displayed number with following the massage. Every
time after adjusting a disc, the disc is replaced and adjustment is
continued automatically.

Set Disc
Disc slot number 1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-

504)

Disc slot number 2: CD (LUV-P01 or YEDS-18 or PATD-012)
Disc slot number 3: DVD-DL (TDV-540C only)

Make sure, using the TDV-540C in this adjustment.

Select [5], insert DVD dual layer disc, and press [ENTER] key, and
the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. The disc slot
No. 3 is used in the changer type model. If there is no disc on the
disc slot No. 3, the tray will be open to wait for closing. If there is a
disc on the table, the adjustment starts immediately. If you put a
disc prior to adjustment, confirm that the DL disc is set on the disc
slot 3.

1. Sled Reset
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. Focus Jump (L0 t L1)
25. Tracking Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off

26

### Drive Manual Operation ###

2. Operation Commands

 1. Search Disc (DVD Priority)

 2. Search Disc (CD Priority)

 3. PLAY

 4. Pause

 5. Stop

Exit: RETURN

[1] Serch Disc

: DVD SDISC (F/E command) is performed by

(DVD Priority)

priority.

[2] Serch Disc

: CD SDISC (F/E command) is performed by

(CD Priority)

priority.

[3] PLAY

: Playback the current disc (DVD/CD).

Start address is DVD = 0x030000 or CD =
00:00:00.

[4] Pause

: Pause

[5] Stop

: Stop

### Drive Manual Operation ###

3. Servo Control

 1. LD DVD      Off/On

 2. LD CD       Off/On

 3. Focus       Off/On

 4. Spindle     Off/On

 5. Track       Off/On

 6. Sled        Off/On

 8. Focus Ramp

Exit: RETURN

On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.

[1] LD DVD

: Turn on/off the laser for DVD.

[2] LD CD

: Turn on/off the laser for CD.

[3] Focus

: Turn on/off the focus servo.

[4] Spindle

: Turn on/off the spindle servo.

[5] Track

: Turn on/off the tracking servo.

[6] Sled

: Turn on/off the sled servo.

[8] Focus Ramp : In the laser diode on and focus servo off status,

repeat the focus up/down.

4. Track/Layer Jump

 1. 1Tj         FWD

 2. 1Tj         REV

 3. 200Tj       FWD

 4. 200Tj       REV

 5. 2kTj        FWD

 6. 2kTj        REV

 9. Lj (L1->L0) FWD

 0. Lj (L0->L1) REV

Exit: RETURN

On this screen, track jump, etc. can be performed. Only for the DVD-
DL, the focus jump and layer jump are displayed in the right field.

[1] 1Tj FWD

: 1-track jump forward.

[2] 1Tj REV

: 1-track jump reverse.

[3] 200Tj FWD : 200-track jump forward.
[4] 200Tj REV : 200-track jump reverse.
[5] 2kTj FWD : 2k-track jump forward.
[6] 2kTj REV

: 2k-track jump reverse.

[9] Lj (L1->L0) : Layer jump.
[0] Lj (L0->L1) : Layer jump.

On the Test Mode Menu screen, select [2], and the manual operation
menu will be displayed. For the manual operation, each servo on/
off control and adjustment can be executed manually.

## Drive Manual Operation ##

2. Operation Commands

3. Servo Control

4. Track/Layer Jump

6. Memory Check

7. Changer Manual Move

8. Changer Mecha Check

Exit: RETURN

Model   :DVP-CX995V

Revision:x.xxx

Basic operation (controllable from front panel or remote
commander)

 

I/

1

: Power OFF

 

x

: Servo stop

 

Z

: Stop+Eject/Loading

 

O

(RETURN) : Return to Operation Menu or Test Mode Menu

 

>

,

.

: Transition between sub modes of menu

[1] to [9], [0]

: Selection of menu and items

Cursor [

Q]/[q] : Increase/Decrease in manually adjusted value

27

[PLAY]

: Loads the disc from the chucking position of

Loading In

the table toward inside the mechanism deck.
When the Disc Load is selected, a series of

operation starting from Loading – Chucking is
performed.

[STOP]

: Moves the disc from inside the mechanism deck

Loading Out

to the table.
When the Disc Unload is selected, a series of

operation starting from Unloading – Chucking
is performed.

[OP/CL]

: Opens and closes the door.

Door Open/Close
( 

Z

key)

[UP]

: Pops up the lever.

Poper Up
([

Q] key)

[DOWN]

: Pops down the lever.

Poper Down
([

q] key)

[jog FOR]*

1

: Moves the table to the right in units of the slit.

Table R step Turn The table number is incremented in the direction

of positive (+) number.

[jog PRV]*

1

: Moves the table to the left in units of the slit.

Table L step Turn

The table number is decremented in the

direction of negative (–) number.

[DISP]

: When this item is selected, the 400CHG Sensor

Sensor Status

Check appears on the screen.

([DISPLAY] key)

*1) Turn the [DISC/AMS] knob on the main unit.

Display when the Sensor Status is selected in the Changer Manual
Move.

## 400CHG Sensor Check ##

 Table 1/2/3/4    : X/X/X/X

 Table lock       : X

 Load in          : X

 Load out         : X

 Door open        : X

 Door close       : X

 Poper up         : X

 Poper down       : X

 Disc Sensor      : XXX

RETURN : Exit

Table 1/2/3/4

: Indicates table sensor 1/2/3/4 status.

(0: Low, 1: High)

Table lock

: Indicates each switch status.

Load in/out

(0: Off, 1: On)

Door open/close
Poper up/down

Disc Sensor

: Indicates sensitivity of the disc sensor.

The value is raging from 0 to 3FF.

The display image is shown below and three screens in total can be
selected.

6. Memory Check Flash Data 1

              CD   SL   L0   L1

 An.Off A     xx   xx   xx   xx

 An.Off B     xx   xx   xx   xx

 An.Off C     xx   xx   xx   xx

 An.Off D     xx   xx   xx   xx

 An.Off E     xx   xx   xx   xx

 An.Off F     xx   xx   xx   xx

 An.G.Main    xx   xx   xx   xx

 An.G.Side    xx   xx   xx   xx

 RF level     xx   xx   xx   xx

 FE S level   xx   xx   xx   xx

Down:NextPage

Exit:RETURN

6. Memory Check Flash Data 2

              CD   SL   L0   L1

 TE Level     xx   xx   xx   xx

 TE Offset    xx   xx   xx   xx

 FCS Gain     xx   xx   xx   xx

 TRK Gain     xx   xx   xx   xx

 FCS Bal.1    xx   xx   xx   xx

 FCS Bal.2    xx   xx   xx   xx

 RFEQ 1       xx   xx   xx   xx

 RFEQ 2       xx   xx   xx   xx

 VTS2         xx   xx   xx   xx

 Jitter       xx   xx   xx   xx

Up/Dn:Prev/NextPage

Exit:RETURN

6. Memory Check Flash Data 3

              CD   SL   L0   L1

 VTS1         xx   xx   xx   xx

Up:PrevPage

Exit:RETURN

On this test mode screen, selecting [7] enables the machine operation
such as disc loading. The following screen appears.

Display when [7] is selected in the Drive Manual Operation

## Changer Manual Move ##

ENTER  : Mecha Initial

PLAY   : Loading In

STOP   : Loading Out

OP/CL  : Door Open/Close

UP     : Poper Up

DOWN   : Poper Down

jogFOR : Table R StepTurn

jogPRV : Table L StepTurn

DISP   : Sensor Status

RETURN : Exit

[ENTER]

: Performs initialization of mechanism deck.

Mecha Initial

Because the mechanical initialization is

performed when the machine enters the Drive
Manual Operation mode, use this item when
an error such as adjustment error occurs.

28

On this test mode screen, selecting [8] enables the table sensor and
the disc sensor adjustment. The following screen appears.

Display when [8] is selected in the Drive Manual Operation

## Changer Mecha Check ##

ENTER  : Mecha Initial

OP/CL  : Disc Load/UnLoad

jogFOR : Table R StepTurn

jogPRV : Table L StepTurn

PLAY   : Table Rotate

PAUSE  : Mecha Adjust

DISP   : Sensor Status

RETURN : Exit

All operations are the same as those of the Changer Manual Move
except [OP/CL], [PLAY] and [PAUSE].

[OP/CL]

: Loads the disc from the chucking position of

Disc Load/UnLoad

the table toward inside the mechanism deck

(

Z

key)

or from inside the mechanism deck to the
table.
When the Disc Load is selected a series of
operation starting from Door Close – Table
Rotate – Chucking is performed.
When the Disc UnLoad is selected a series of
operation starting from Unchucking – Table
Rotate – Door Open is performed.

[PLAY]

: Enters the Disc Sensor Adjustment Mode.

Table Rotate

The 400CHG Table Rotate appears on the
screen.

[PAUSE]

: Enters the Table Sensor Adjustment Mode.

Mecha Adjust

The 400CHG Mecha Adjust appears on the
screen.

Display when [PLAY] is selected in the Changer Mecha Check.

Refer to page 32 for “TABLE SENSOR ADJUSTMENT”.

## 400CHG Table Rotate ##

 RIGHT : Turn Right

 LEFT  : Turn Left

 Table 1/2/3/4    : X/X/X/X

 Disc Sensor      : XXX

RETURN : Exit

[RIGHT]*

1

: Rotates table counterclockwise.

Turn Right

[LEFT]*

1

: Rotates table clockwise.

Turn Left

Table 1/2/3/4

: These items are the same as those of the

Disc Sensor

400CHG Sensor Check.

*1) Turn the [DISC/AMS] knob on the main unit.

Display when [PAUSE] is selected in the Changer Mecha Check.

Refer to page 32 for “POP UP MECHANISM ADJUSTMENT”.

## 400CHG Mecha Adjust ##

 UP    : Load in

 DOWN  : Load out

 RIGHT : Pop Up

 LEFT  : Pop Down

 Table 1/2/3/4    : X/X/X/X

RETURN : Exit

[UP]

: Loads the disc from the chucking position of the

Load in

table  toward  inside the mechanism deck during
pressing the [

Q] key.

[DOWN]

: Loads the disc from inside the mechanism deck to

Load out

the table during pressing the [

q] key.

[RIGHT]

: Pops up the lever during pressing the [

w] key.

Pop Up

[LEFT]

: Pops down the lever during pressing the [

W] key.

Pop Down

Table 1/2/3/4 : This item is the same as that of the 400CHG Sensor

Check.