Sony DVP-CX860 / DVP-CX870D Service Manual ▷ View online
5-1
SECTION 5
IC PIN FUNCTION DESCRIPTION
D
VP-CX860/CX870D
Pin No.
Pin name
I/O
Function
39
SC1
O
Serial clock output
40
SI2
I
Serial bus 2 (for data input)
41
SO2
O
Serial bus 2 (for data output)
42
YUVRGB/GAIN/CKSW2
O
Mute signal output to video buffer and EURO C/R
select signal output
select signal output
43
DREQ0
I
Input of DMA-REQ 0 from AV DEC
44
DACK0
O
Output of DMA-ACK 0 to AV DEC
45
IFCS
O
Chip select signal to IF CON
46
DREQ1
I
Input of DMA-REQ 1 from AV DEC
47
DACK1
O
Output of DMA-ACK 1 to AV DEC
48
EWC
O
Write control signal output to EEPROM
49
ECS
O
Chip select signal output to EEPROM
50
KCS/39CS
O
Chip select signal output to audio DSP
51
AURST
O
Reset signal output to audio DAC
52
VSS
–
Ground
53
X1
O
Clock output (12.5 MHz)
54
X0
I
Clock input (12.5 MHz)
55
VCC
–
Power supply
56
CKSW1
I
Chuck sensor input
57
OCSW1
I
Tray sensor input
58
OCSW2
I
Tray sensor input
59
DACCS0
O
Chip select signal output to DAC (2ch)
60
DACCS1
O
Chip select signal output to DAC (6ch) and DSP
61
48/44.1K
O
PLL FS control signal output
62
MAMUTE
O
Audio mute signal output
63
WIDE
O
WIDE select signal output
64
C
–
Capacitor (0.1uF) connect between ground
65
CS0X
O
External ROM chip select signal output
66
CS1X
–
Not used
67
CS2X
O
Chip select signal output (for AV DEC)
68
CS3X
O
Chip select signal output (for AV DEC)
69
CS4X
O
Chip select signal output (for ARP)
70
CS5X
O
Chip select signal output (for FGA)
Pin No.
Pin name
I/O
Function
1–5
HA17-HA21
O
Address bus A17-A21
6
HA22
–
Not used
7
RGBSEL
O
Color difference signal/RGB signal select signal output
8
DACMUTE/FS
O
Filter control signal output
9
AVCC
–
Power supply
10
AVRH
–
Reference power supply (+3.3 V)
11
AVSS
–
Ground
12
AN0
I
Set of mode 0
13
AN1
I
Set of mode 1
14
AN2
I
Set of mode 2
15
AN3
I
Set of mode 3
16
XRST
O
System reset signal output
17
POFF
–
Not used
18
CSb
O
Chip select signal for servo DSP
19
NC
–
Not used
20
EUROV/Y/VFC1
O
EURO V/Y select signal output
21
DISCEXT/VFC2
O
Line input select signal output (DISC: “H”, EXT: “ L”)
22
ARPRST
O
Reset signal output for ARP
23
DRVMUTE
O
Drive mute signal output
24
VCC
–
Power supply
25
INT0
I
Input of interrupt from AV DEC
26
INT1
I
Input of interrupt from ARP
27
INT2
I
Input of interrupt from FGA
28
INT3
I
Input of interrupt from EEPROM
29
INT4
I
Input of interrupt from IF CON
30
INT5
I
Input of interrupt from audio DSP
31
INT6
I
Input of interrupt from audio DSP
32
INT7
I
Input of interrupt from servo DSP
33
SI0
I
Serial data input from IF CON and EEPROM
34
VSS
–
Ground
35
SO0
O
Serial data output to IF CON and EEPROM
36
SC0
O
Serial clock output to IF CON and EEPROM
37
SI1
I
Serial bus 1 (for data input)
38
SO1
O
Serial bus 1 (for data output)
5-1.
SYSTEM CONTROL PIN FUNCTION MB91108PFV-G-BND (MB-94 BOARD IC102)
5-2E
Pin No.
Pin name
I/O
Function
71
CPUCK
O
CPU clock signal output
72
NMIX
–
Not used (fixed at “H”)
73
HSTX
–
Not used (fixed at “H”)
74
FRRSTIN
I
Reset signal input from IF CON
75
VSS
–
Ground
76
MD0
I
Input of mode select 0 (fixed at “1”)
77
MD1
–
Ground
78
MD2
–
Ground
79
XWAIT
I
Wait signal input
80
BGRNTX
–
Test terminal (fixed at “H”)
81
BRQ
–
Test terminal (fixed at “L”)
82
RD
O
Read enable signal output
83
WRH
O
High byte write enable signal output (16 bit and 8 bit)
84
NC
–
Not used
85–92
HD0-HD7
I/O
Data bus D0-D7 (16 bit only)
93–100
HD8-HD15
I/O
Data bus D8-D15 (16 bit) , D0-D7 (8 bit)
101
VSS
–
Ground
102–109
HA0-HA7
O
Address bus A00-A07
110
VCC
–
Power supply
111–118
HA8-HA15
O
Address bus A08-A15
119
VSS
–
Ground
120
HA16
O
Address bus A16
6-1
SECTION 6
TEST MODE
DVP-CX860/CX870D
6-1.
GENERAL DESCRIPTION
The Test Mode allows you to make diagnosis and adjustment eas-
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
6-2.
STARTING TEST MODE
At the bottom of menu screen, the model name and revision num-
ber are displayed. The “T table” that appers on the screen means
the turn table.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the POWER button.
ber are displayed. The “T table” that appers on the screen means
the turn table.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the POWER button.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Version Information
6. Video Level Adjustment
Exit: Power Key
_
Model
: DPX13xxxx
Revision
: x.xxx
6-3.
SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press
checked from the remote commander.
On the Test Mode Menu screen, press
[0]
key on the remote com-
mander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1. All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
[NEXT]
key to go to the next item,
or
[PREV]
key to repeat the same check again. To quit the diagno-
sis and return to the Check Menu screen, press
[STOP]
or
[ENTER]
key. If an error occurred, the diagnosis is suspended
and the error code is displayed as shown below.
### Syscon Diagnosis ###
3-2. EEPROM Check
Error 03: EEPROM Write/Reed N
Address
: 00000001
Write Data : 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press
[STOP]
key to quit the diagnosis, or
[PREV]
key to repeat
the same item where an error occurred, or
[NEXT]
key to continue
the check from the item next to faulty item.
Subnemu
Selecting 2 and subsequent items calls the submenu screen of each
item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
0. Quit
Quit the submenu and return to the main menu.
6-2
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file of ROM
(IC106) is displayed with four digits.
Error: Not detected.
The revision number defined in the source file of ROM
(IC106) is displayed with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
The data are added of ROM (IC106) and the result is dis-
played with 4-digit hexadecimal number. Error is not de-
tected. Compare the result with the specified value.
Error: Not detected.
The data are added of ROM (IC106) and the result is dis-
played with 4-digit hexadecimal number. Error is not de-
tected. Compare the result with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code is displayed with 2-digit hexadecimal num-
ber.
Error: Not detected.
The model code is displayed with 2-digit hexadecimal num-
ber.
Model Type
DVP-CX860 (US, CND)
6
0
DVP-CX860 (AEP, UK)
6
3
DVP-CX870D (US, CND)
7
0
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is dis-
played.
Error: Not detected.
The region code determined from the model code is dis-
played.
3. Peripheral
(3-2) EEPROM Check
Data write
→
read, and accord check
Error 03: EEPROM write/read discord
Before writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
Before writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
(3-3) Gate Array Check
Data write
→
read, and accord check
Error 02: Gate array write/read discord
4. Servo
(4-2) Servo DSP Check
Data write
→
read, and accord check
Error 12: Read data discord
(4-3) DSP Driver Test
Test signal data
→
DSP Driver
Error: Not detected.
5. Supply
Caution: Do not conduct this check with a mechanical deck con-
nected.
An access is made to the stream supply and servo con-
trol IC (IC302) and external RAM (IC303) using check
data. If mechanical deck is connected, the motor and
optics could be damaged. This check is also executed by
the “All” menu item.
An access is made to the stream supply and servo con-
trol IC (IC302) and external RAM (IC303) using check
data. If mechanical deck is connected, the motor and
optics could be damaged. This check is also executed by
the “All” menu item.
Supplement: How to disconnect mechanical deck
Disconnect flexible flat cables connected to the
CN201 and CN202 of MB-86 board. Also, discon-
nect flat cable from the CN401.
CN201 and CN202 of MB-86 board. Also, discon-
nect flat cable from the CN401.
(5-2) ARP Register Check
Data write
→
read, and accord check
Error 08: ARP register write, and read data discord
(5-3) ARP to RAM Data Bus
Data write
→
read, and accord check
Error 09: ARP
←→
RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
1. All
All submenu items continuous check
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another au-
tomatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “Check Items List”.
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another au-
tomatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “Check Items List”.
Click on the first or last page to see other DVP-CX860 / DVP-CX870D service manuals if exist.