Sony DAV-DZ110 / DAV-DZ111 / DAV-DZ120 / DAV-DZ120K / HCD-DZ110 / HCD-DZ111 / HCD-DZ120 / HCD-DZ120K Service Manual ▷ View online
5
HCD-DZ110/DZ111/DZ120/DZ120K
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
disc in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the
x
button and the
A
button simultaneously for five
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the
x
button and the
A
button simultaneously for five
seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note:
When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the ?/1 button.
turning power on/off with the ?/1 button.
Note on MAIN board replacement
New part of EEP ROM (IC1103) on the MAIN board cannot be used.
Therefore, if the mounted MAIN board (A-1144-739-A, etc.) is replaced,
Therefore, if the mounted MAIN board (A-1144-739-A, etc.) is replaced,
exchange new EEP ROM (IC1103) with that used before the replacement.
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the screen and the front panel display. In this
case, check the following table.
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the screen and the front panel display. In this
case, check the following table.
When displaying the version
number on the screen
number on the screen
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
number [VER.X.XX] (X is a number) may
appear on the screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
Self-diagnosis Function
(When letters/numbers appear in the
display)
display)
First 3
characters of
the service
number
characters of
the service
number
Cause and/or corrective action
C 13
The disc is dirty.
,Clean the disc with a soft cloth
C 31
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
E XX
(xx is a number)
To prevent a malfunction, the
system has performed the self-
diagnosis function.
system has performed the self-
diagnosis function.
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
service facility and give the 5-
character service number.
Example: E 61 10
C:13:50
VER.X.XX
6
HCD-DZ110/DZ111/DZ120/DZ120K
HOW TO OPEN THE DISC TABLE WHEN POWER SWITCH TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and slide
it in the direction of the arrow.
it in the direction of the arrow.
disc tray
tapering driver
CN3002
MAIN BOARD
POWER BOARD
CN902
RED
BLACK
C903
C939
C933
C932
Discharge the charged electricity in capacitors to prevent electric shock as follows
When disassembling the machine, be sure to discharge the charged electricity in the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
POWER board
C903 : 600V
C932, C933, C939, CN902 : 30V
C903 : 600V
C932, C933, C939, CN902 : 30V
MAIN board
CN3002 : 30 V
CN3002 : 30 V
(Parts face side)
(Parts face side)
*
Connect the specified resistor
between black and red leads
7
HCD-DZ110/DZ111/DZ120/DZ120K
Fix the capacitors with adhesive agent as follows
Fixing the capacitors with adhesive agent is required by the safety regulation.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
POWER BOARD
C910
C924
IC921
C930
%
%
PRECAUTION WHEN INSTALLING A NEW OP UNIT /
PRECAUTION BEFOR UNSOLDERING THE STATIC ELECTRICITY
PREVENTION SOLDER BRIDGE
PRECAUTION BEFOR UNSOLDERING THE STATIC ELECTRICITY
PREVENTION SOLDER BRIDGE
When installing a new OP unit, be sure to connect the flexible
printed circuit board first of all before removing the static electricity
prevention solder bridge by unsoldering. Remove the static electricity
prevention solder bridge by unsoldering after the flexible printed
circuit board has already been connected.
(Do not remove nor unsolder the solder bridge
as long as the OP unit is kept standalone.)
printed circuit board first of all before removing the static electricity
prevention solder bridge by unsoldering. Remove the static electricity
prevention solder bridge by unsoldering after the flexible printed
circuit board has already been connected.
(Do not remove nor unsolder the solder bridge
as long as the OP unit is kept standalone.)
8
HCD-DZ110/DZ111/DZ120/DZ120K
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Front panel
A "
/
1
(on/standby) (23)
B
Front panel display (83)
C A
(open/close) (23)
D
Disc operation (23)
E
FUNCTION (23)
F
(remote sensor) (8)
G
PHON
MIC 2 jack (DZ120K)
ES jack (23)
H
VOLUME control (23)
I
AUDIO IN ja
AUDIO IN/A.CAL MIC jack (DZ120)
AUDIO IN/MIC 1/A.CAL MIC jack (DZ120K)
AUDIO IN/MIC 1/A.CAL MIC jack (DZ120K)
ck (15, 24)
J
Disc tray (23)
Rear panel
DZ110/DZ111
A
SPEAKER jacks (9)
B
COMPONENT VIDEO OUT jacks (19)
C
EURO AV
T
OUTPUT (TO TV) jack (9,
19)
D
AM terminal (9)
E
COAXIAL FM 75
Ω
jack (9)
F
LINE (AUDIO IN R/L) jacks (22)
COAXIAL
AM
FM
75
SPEAKER
EURO AV
FRONT R
FRONT L
SUR R
SUR L
CENTER
WOOFER
OUTPUT(TO TV)
COMPONENT VIDEO OUT
Y
P
B
/C
B
P
R
/C
R
(DVD ONLY)
R
L
AUDIO IN
LINE
Rear panel
DZ120/DZ120K
A
SPEAKER jacks (10)
B
TV/VCR (AUDIO IN R/L) jacks (23)
C
COMPONENT VIDEO OUT jacks (20)
D
MONITOR OUT (S VIDEO/VIDEO) jacks
(20)
(20)
E
AM terminal (10)
F
COAXIAL FM 75
Ω
jack (10)
R
L
AUDIO IN
COAXIAL
AM
FM
75
COMPONENT VIDEO OUT
TV/VCR
(DVD ONLY)
Y
P
B
/C
B
P
R
/C
R
SPEAKER
FRONT R
FRONT L
SUR R
SUR L
CENTER
WOOFER
VIDEO
(DVD ONLY)
S VIDEO
MONITOR OUT
Click on the first or last page to see other DAV-DZ110 / DAV-DZ111 / DAV-DZ120 / DAV-DZ120K / HCD-DZ110 / HCD-DZ111 / HCD-DZ120 / HCD-DZ120K service manuals if exist.