Sony DAV-DZ110 / DAV-DZ111 / DAV-DZ120 / DAV-DZ120K / HCD-DZ110 / HCD-DZ111 / HCD-DZ120 / HCD-DZ120K Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
US Model
Canadian Model
HCD-DZ120
AEP Model
HCD-DZ110/DZ120/DZ120K
UK Model
HCD-DZ110/DZ111
E Model
HCD-DZ120/DZ120K
Australian Model
HCD-DZ120
SUPER AUDIO CD/DVD RECEIVER
9-887-019-05
2006H16-1
© 2006.08
© 2006.08
Ver. 1.4 2006.08
HCD-DZ110/DZ111/
DZ120/DZ120K
HCD-DZ110/DZ111/DZ120/DZ120K are the amplifier, DVD/CD
and tuner section in DAV-DZ110/DZ111/DZ120/DZ120K.
and tuner section in DAV-DZ110/DZ111/DZ120/DZ120K.
SPECIFICATIONS
Model Name Using Similar Mechanism
HCD-DZ100
Mechanism Type
CDM85-DVBU102
Optical Pick-up Name
KHM-310CAA
This system incorporates with Dolby*
1
Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS*
2
Digital Surround
System.
*1 Manufactured under license from Dolby Laboratories.
*1 Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc.
Theater Systems, Inc.
— Continued on next page —
Photo : HCD-DZ110
AUDIO POWER SPECIFICATIONS
for the US model
for the US model
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION
(FTC Output Power):
TOTAL HARMONIC
DISTORTION
(FTC Output Power):
FL/FR/LS/RS/C: 84 W/ch
3 ohm at 180 - 20,000 Hz,
0.7 % THD
SW: 80 W 3 ohm at 40 -
180 Hz, 0.7 % THD
3 ohm at 180 - 20,000 Hz,
0.7 % THD
SW: 80 W 3 ohm at 40 -
180 Hz, 0.7 % THD
US models:
Surround mode (reference) RMS output power, 10 %
Surround mode (reference) RMS output power, 10 %
THD
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Other models:
Stereo mode (rated)
Stereo mode (rated)
108 W + 108 W (3 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 %
THD
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Amplifier section
DZ110
DZ110
Stereo mode (rated)
108 W + 108 W (3 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 %
THD
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142 W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS51)
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142 W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS51)
DZ111
DZ120
DZ120
Stereo mode (rated)
108 W + 108 W (3 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 %
THD
Front: 142 W + 142 W
(with SS-TS31A)
Center*: 142 W
(with SS-CT31A)
Surround*: 142 W + 142 W
(with SS-TS31A)
Subwoofer*: 140 W
(with SS-WS33)
Front: 142 W + 142 W
(with SS-TS31A)
Center*: 142 W
(with SS-CT31A)
Surround*: 142 W + 142 W
(with SS-TS31A)
Subwoofer*: 140 W
(with SS-WS33)
DZ120K
Latin American models:
Stereo mode (rated)
Stereo mode (rated)
100 W + 100 W (3 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 %
THD
Front: 133 W + 133 W
(with SS-TS51)
Center*: 133 W
(with SS-CT51)
Surround*: 133 W + 133
W
(with SS-TS51)
Subwoofer*: 135 W
(with SS-WS52)
Front: 133 W + 133 W
(with SS-TS51)
Center*: 133 W
(with SS-CT51)
Surround*: 133 W + 133
W
(with SS-TS51)
Subwoofer*: 135 W
(with SS-WS52)
2
HCD-DZ110/DZ111/DZ120/DZ120K
MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
Model
Part No.
DZ110 : AEP, UK models
2-653-933-0
[]
DZ111 : UK model
2-653-933-1
[]
DZ120 : AUS, RU models
2-653-933-2
[]
DZ120K : SP, E12, E32, AR, KR, TW models
DZ120 : US, CND models/
2-653-933-3
[]
DZ120K : MX model
DZ120K : E3 model
2-653-933-5
[]
DZ120K : RU model
2-661-239-2
[]
DZ120K : EA model
2-661-239-3
[]
•
Abbreviation
AUS : Australian Model
AR
AUS : Australian Model
AR
: Argentina model
CND : Canadian Model
E3
E3
: 240V AC area in E model
E12 : 220-240V AC area in E model
E32 : 110-240V AC area in E model
EA
E32 : 110-240V AC area in E model
EA
: Saudi Arabia model
KR
: Korean model
MX : Mexican model
RU
RU
: Russian model
SP
: Singapore model
TW
: Taiwan model
SPEAKER
FRONT R
FRONT L
SUR R
SUR L
CENTER
Parts No.
WOOFER
European models:
Other models:
Tuner section
System
PLL quartz-locked digital
synthesizer system
synthesizer system
FM tuner section
Tuning range
North American models:
Tuning range
North American models:
87.5 – 108.0 MHz
(100 kHz step)
(100 kHz step)
Other models:
87.5 – 108.0 MHz
(50 kHz step)
(50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
North American models:
Tuning range
North American models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Other models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section
Outputs
Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
Outputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
General
Power requirements
North American and Mexican models:
North American and Mexican models:
120
Latin American model :
110 - 240 V AC, 50/60Hz
Taiwan model :
120 V AC, 50/60Hz
V AC, 60 Hz
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
TV/VCR (AUDIO IN)
TV/VCR (AUDIO IN)
Sensitivity: 450/250 mV
AUDIO IN/MIC
Sensitivity: 250/125 mV
Outputs (Analog)
Phones
Phones
Accepts low-and high-
impedance headphones.
impedance headphones.
Inputs (Analog)
LINE (AUDIO IN)
LINE (AUDIO IN)
Sensitivity: 450/250 mV
Impedance: 50 kilohms
Impedance: 50 kilohms
Phones
Accepts low-and high-
impedance headphones.
impedance headphones.
AUDIO IN
Sensitivity: 250/125 mV
Impedance: 50 kilohms
Impedance: 50 kilohms
DZ110/DZ111
DVD system
Laser
Semiconductor laser
(DVD:
λ = 650 nm)
(CD:
λ = 790 nm)
Emission duration:
continuous
continuous
S
European models:
Mexican and North American models:
European models:
Mexican and North American models:
Other models:
ignal format system
PAL
NTSC
NTSC/PAL
NTSC/PAL
Frequency response (at 2 CH STEREO mode)
DVD (PCM): 2 Hz to 22
kHz (
kHz (
±1.0 dB)
CD: 2 Hz to 20 kHz (
±1.0
dB)
Harmonic distortion
Less than 0.03 %
DZ120K
DZ110/DZ111
DZ120
DZ120K
Mexican and other models:
Stereo mode (rated)
Stereo mode (rated)
108 W + 108 W (3 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 %
THD
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Front: 142 W + 142 W
(with SS-TS51)
Center*: 142 W
(with SS-CT51)
Surround*: 142 W + 142
W
(with SS-TS51)
Subwoofer*: 140 W
(with SS-WS52)
Inputs (Analog)
TV/VCR (AUDIO IN/VIDEO IN)
TV/VCR (AUDIO IN/VIDEO IN)
Sensitivity: 450/250 mV
AUDIO IN/MIC 1/MIC
Sensitivity: AUDIO IN
250/125 mV/MIC 1 1 mv
250/125 mV/MIC 1 1 mv
MIC 2
Sensitivity: 1 mV
Other models:
220 - 240 V AC, 50/60 Hz
Power consumption
On: 150 W
Standby: 0.3 W (at the
Power Saving Mode)
Standby: 0.3 W (at the
Power Saving Mode)
Dimensions (approx.)
430
× 55 × 360 mm
Mass (approx.)
3.8 kg
Design and specifications are subject to change
without notice.
without notice.
(17
× 2
1
/
4
× 14
1
/
4
inches)
(w/h/d) incl. projecting
parts
parts
Ver. 1.3
3
HCD-DZ110/DZ111/DZ120/DZ120K
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
This marking is located on
the bottom exterior.
a CLASS 1 LASER product.
This marking is located on
the bottom exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Fig. A.
Using an AC voltmeter to check AC leakage.
4
HCD-DZ110/DZ111/DZ120/DZ120K
TABLE OF CONTENTS
1.
SERVICING NOTE
...................................................
5
2.
GENERAL
...................................................................
8
3.
DISASSEMBLY
3-1.
Disassembly Flow ........................................................... 11
3-2.
Case, Front Panel Assy .................................................... 12
3-3.
FL Board .......................................................................... 13
3-4.
JACK Board, SW Board .................................................. 13
3-5.
I/O Board (DZ120/DZ120K), I/O SCART Board
(DZ110/DZ111) ............................................................... 14
(DZ110/DZ111) ............................................................... 14
3-6.
MAIN Board .................................................................... 14
3-7.
DC Fan, Tuner Unit ......................................................... 15
3-8.
POWER Board ................................................................ 15
3-9.
DVD Mechanism Deck (CDM85-DVBU102) ................ 16
3-10. Tray .................................................................................. 16
3-11. Belt, MS-203 Board ........................................................ 17
3-12. Optical Pick-up (KHM-310CAA) ................................... 18
3-11. Belt, MS-203 Board ........................................................ 17
3-12. Optical Pick-up (KHM-310CAA) ................................... 18
4.
TEST MODE
............................................................... 19
5.
ELECTRICAL ADJUSTMENT
............................. 23
6.
DIAGRAMS
6-1.
Block Diagram – RF Section – ....................................... 26
6-2.
Block Diagram – AMP Section – ................................... 27
6-3.
Block Diagram – AUDIO Section – ............................... 28
6-4.
Block Diagram – VIDEO Section – ............................... 29
6-5.
Block Diagram – POWER Section – .............................. 30
6-6.
Printed Wiring Board – MAIN Board (Side A) – ............ 31
6-7.
Printed Wiring Board – MAIN Board (Side B) – ............ 32
6-8.
Schematic Diagram – MAIN Board (1/10) – ................. 33
6-9.
Schematic Diagram – MAIN Board (2/10) – ................. 34
6-10. Schematic Diagram – MAIN Board (3/10) – ................. 35
6-11. Schematic Diagram – MAIN Board (4/10) – ................. 36
6-12. Schematic Diagram – MAIN Board (5/10) – ................. 37
6-13. Schematic Diagram – MAIN Board (6/10) – ................. 38
6-14. Schematic Diagram – MAIN Board (7/10) – ................. 39
6-15. Schematic Diagram – MAIN Board (8/10) – ................. 40
6-16. Schematic Diagram – MAIN Board (9/10) – ................. 41
6-17. Schematic Diagram – MAIN Board (10/10) – ............... 42
6-18. Printed Wiring Board – I/O Board (DZ120/DZ120K) – . 43
6-19. Schematic Diagram – I/O Board (DZ120/DZ120K) – ... 44
6-20. Printed Wiring Board
6-11. Schematic Diagram – MAIN Board (4/10) – ................. 36
6-12. Schematic Diagram – MAIN Board (5/10) – ................. 37
6-13. Schematic Diagram – MAIN Board (6/10) – ................. 38
6-14. Schematic Diagram – MAIN Board (7/10) – ................. 39
6-15. Schematic Diagram – MAIN Board (8/10) – ................. 40
6-16. Schematic Diagram – MAIN Board (9/10) – ................. 41
6-17. Schematic Diagram – MAIN Board (10/10) – ............... 42
6-18. Printed Wiring Board – I/O Board (DZ120/DZ120K) – . 43
6-19. Schematic Diagram – I/O Board (DZ120/DZ120K) – ... 44
6-20. Printed Wiring Board
– I/O SCART Board (Side A) (DZ110/DZ111) – ........... 45
6-21. Printed Wiring Board
– I/O SCART Board (Side B) (DZ110/DZ111) – ........... 46
6-22. Schematic Diagram
– I/O SCART Board (DZ110/DZ111) – .......................... 47
6-23. Printed Wiring Board – PANEL Section – ...................... 48
6-24. Schematic Diagram – PANEL Section – ....................... 49
6-25. Printed Wiring Board – SPEAKER Board – ................... 50
6-26. Schematic Diagram – SPEAKER Board – .................... 50
6-27. Printed Wiring Board – MS-203 Board – ........................ 51
6-28. Schematic Diagram – MS-203 Board – ........................ 51
6-29. Printed Wiring Board – POWER Board – ....................... 52
6-30. Schematic Diagram – POWER Board – ........................ 53
6-24. Schematic Diagram – PANEL Section – ....................... 49
6-25. Printed Wiring Board – SPEAKER Board – ................... 50
6-26. Schematic Diagram – SPEAKER Board – .................... 50
6-27. Printed Wiring Board – MS-203 Board – ........................ 51
6-28. Schematic Diagram – MS-203 Board – ........................ 51
6-29. Printed Wiring Board – POWER Board – ....................... 52
6-30. Schematic Diagram – POWER Board – ........................ 53
7.
EXPLODED VIEWS
7-1.
Overall Section ................................................................ 64
7-2.
Front Panel Section ......................................................... 65
7-3.
Chassis Section-1 ............................................................ 66
7-4.
Chassis Section-2 ............................................................ 67
7-5.
DVD Mechanism Deck Section (CDM85-DVBU102) ... 68
8.
ELECTRICAL PARTS LIST
.................................. 69