DOWNLOAD Sony DAV-C770 / HCD-C770 / HCD-C990 Service Manual ↓ Size: 11.23 MB | Pages: 127 in PDF or view online for FREE

5

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.

extension cable
(RF board-DVD board)
(Part No. J-2501-217-A)

extension cable
(DVD board-AMP board)
(Part No. J-8000-024-A)

extension cable
(DVD board-AMP board)
(Part No. J-2501-198-A)

extension cable
(relay board-DVD board)
(Part No. J-2501-143-A)

The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.

Releasing Procedure:
1. Press two buttons of 

[DISC 1]

 and

x

simultaneously for five

seconds.

2. The message “UNLOCKED” is displayed and the slot is un-

locked.

When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the 

[POWER]

 button.

Some of the signal of remote commander vary between generation
of player.
Between DAV-S400/S500/S800/C450/C700/C900 and DAV-S550/
S880/C770/C900, remote commander signal codes of
“FUNCTION”, “BAND”, “ST/MONO” and “MEMORY” are
different.
Take notice of the above when you check the operation with remote
commanders of different models.

When replacing the DVD board, since the adjustment value is not
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.

Procedure:
1. Set the test mode. (See page 25)
2. Press the 

[2]

 key of the remote commander, and set the “DRIVE

MANUAL OPERATION”. (See page 26)

3. Press the 

[6]

 key of the remote commander, and set the “2-6,

Memory Check”. (See page 28)

4. Press the 

[CLEAR]

 key of the remote commander, and initial-

ize Memory.

When repairing this set, etc., connect the extension cable as the
figure shown below.

6

1 SPEAKER jacks 
2 AM antenna 
3 VIDEO 1 jacks 
4 VIDEO 2 jacks 
5 COMPONENT VIDEO OUT/SCAN

SELECT switch 

6 MONITOR OUT (VIDEO/S VIDEO)

jacks 

7 VIDEO 2 (OPTICAL DIGITAL IN)

jack 

8 COMPONENT VIDEO OUT jacks
9 FM 75Ω COAXIAL antenna jack 

WOOFER 3

Ω

IMPEDANCE

USE

EXCEPT
WOOFER 3

Ω

FRONT

R

FRONT

L

R E A R

R

R E A R

L

CENTER

WOOFER

COAXIAL

AUDIO OUT

AUDIO IN

L

R

L

R

L

R

VIDEO OUT

VIDEO IN

VIDEO IN

AUDIO IN

Y

P

B

/C

B

P

R

/C

R

AM

FM

75

Ω

O P T I C A L

D I G I T A L

I N

S    VIDEO

VIDEO

DVD 
ONLY

INTERLACE

SELECTABLE

SCAN SELECT

This section is extracted from
instruction manual.

1 POWER switch 
2 STANDBY indicator 
3 DISC 1 (play) /A (Eject)/indicator –

DISC 5 (play) /A (Eject)/indicator 

4

H (play) 

5

X (pause) 

6

x (stop) 

7

./> PREV/NEXT, PRESET –/+

FUNCTION

BAND

DISPLAY

SOUND FIELD

PHONES

STANDBY

8 PHONES jack 

9 VOLUME control 
0 SOUND FIELD –/+
qa DISPLAY 
qs BAND 
qd FUNCTION 
qf Disc slot 
qg Front panel display 
qh

 (remote sensor)

7

ALL 1 DISC S

TRACK

INDEX

M

S

SHUFFLE

PROG PBC

REPEAT 1

DIGITAL

SACD

PCM

DIGITAL

PCM

PRO

ALL 1 DISC S

LOGIC

TITLE

CHAPTER

H

M

S

REPEAT 1

ANGLE

FM AM

TUNED

MONO ST

MHz

Current band

Preset number

Monaural/Stereo effect

Current station

Playing status

Current track number

Current play mode

Lights up during
PBC playback
(VIDEO CD only)

Playing time

Current index number
(The index indicator does not appear during Super
Audio CD or MP3 playback.)

Playing status

Current title number

Playing time

Current sound

Current repeat
mode

Current chapter number

Current surround format

Play mode

Play mode

Current sound

Lights up when you can
change the angle

8

1

2

3

4

5

6

7

>10

10/0

8

9

1 TV [/1 (on/standby) 
2

Z (EJECT) 

3 NAME 
4 STEREO/MONO 
5 MEMORY
6 CLEAR 

7 PLAY MODE 
8 AUDIO 
9 ANGLE 
q; SUBTITLE 
qa VOL +/– 
qs

./> PREV/NEXT, TV CH –/+,
PRESET –/+ 

qd

H PLAY/SELECT 

qf DVD TOP MENU
qg DVD DISPLAY 
qh C/X/x/c/ENTER 
qj DVD SETUP 
qk

1 (standby) 

ql DISC SKIP 
w; TV/VIDEO 
wa REPEAT 
ws MUTING 
wd TIME 
wf FUNCTION 

wg BAND 
wh Number buttons
wj SOUND FIELD 
wk DISPLAY 
wl ENTER 
e; COMMAND MODE DVD TV switch

ea

m/M/

/

 SLOW, TUNING –/+

es

x STOP 

ed

X PAUSE 

ef DVD MENU 
eg

O RETURN 

eh AMP MENU 

This remote control glows in the dark. However,
before glowing, the remote must be exposed to light
for awhile.