DOWNLOAD Sony BDP-S6200 Service Manual ↓ Size: 3.39 MB | Pages: 54 in PDF or view online for FREE

1-2-9 In case of BU assy replacement:
             1. OP related data for new assy is controlled by BU factory
             2. All of data is recorded into a barcode label
             3. The label is put on the assy
             4. Service parts will be followed
             5. In service, the data should be read out from problem assy
             6. The read data should be saved to new assy

1-2-10. Fact fi nding:
             1. The label is “DATA MATRIX” format
             2. The number of data is 91 words
             3. The method of reading and saving is required when BU and main board are replaced.

1-2-11. New service method
             1. All of BU data on the barcode label is shot by digital camera in order to make a JPEG fi le of BU data.
             2. Application software in the PC makes digital data from JPEG fi le.
             3. The converted data is stored to USB memory.
             4. The USB memory is connected to BDP 8G unit.
             5. In service mode, there is a command to save the data from USB memory to board memory.

Description: BDPRdec.exe

          When instruction to PC, password is required. The password will be supplied to only service HQ, and service center name, 
q’ty and all of software registered information should be maintained by service HQ, and Video will ask to report the 
registration information.

Shoot the barcode
Format is JPEG

Save the TEXT data

USB device is connected 
to         symbol on the 
rear unit, and the TEXT 
data as new data is 
loaded to unit by service 
mode.

Application Software
Data convert from
JPEG

TEXT

1-9

 
 

1. From XMB(home menu), select “Setup”

 

2.Select “System Setting” and press “ ENTER” key

 

3. Select “System Information” and push “ENTER” key.

 

4. Device ID is shown on the display. (figure 2.1)

 
  

    DEVICE  ID : XX:XX: XX:XX: XX:XX        <= 12 digit

       If you need deleting of customer’s registration, please contact to service HQ with Device ID information.

(figure 2.1)

1-10E

2-1

• This set can be disassembled in the order shown below.

SET

 2-2  SIDE PANEL AND 
        TRAY COVER ASSY
        

 

(Page 2-1)

 2-3  TOP PANEL, FR-1304
        BOARD AND WLAN 
        MODULE  

 

(Page 2-2)

 2-4  SWITCHING
        REGULATOR
        (Page 2-2)

 2-5  MB-1302 BOARD
        

 

(Page 2-3)

 2-6  BD DRIVE
        

 

(Page 2-3)

1

Two screws +BTP 3x8 Type 2N.S

2

Side Panel (Left)

2

Side Panel (Right)

3

Insert a clip in the hole of a
drive to open a tray

5

Cover tray assy

4

Tray open

(tightening torque = 5 to 6 kgf.cm)

2-2

 

5

7

8

4

6

 

WLAN Module

 

Harness（WIF-1004）

FR-1304 Board

 

One crew（BV3（3-CR））

 

（tightening torque = 5∼6 kgf・cm）

4

 

Flexible flat cable

 

（FIM-1004）（CN701）

2

 

 

（tightening torque = 5∼6 kgf・cm）

1

 

Five hook

Top panel

3

 

One screw（BV3（3-CR））

 

（tightening torque= 5∼6 kgf・cm）

1 Release 

PS insulator clip

Two screws +BV3(3-CR)

Harness (PM-1004)

(CN201)

2

3

PS insulator

5

Switching regulator