DOWNLOAD Sony AVD-C70ES Service Manual ↓ Size: 13.78 MB | Pages: 114 in PDF or view online for FREE

21

Disc Check Memory

 1. SL Disc check

 2. CD Disc check

 3. DL Disc check

Exit: RETURN

On this screen, measure the mirror time of chucked disc, and write
to the EEPROM.

Error Rate Display

UC

CR

ADD

PI1 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

PI2 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

PO  Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

Exit: RETURN

On this screen, measure and display the error rate.

UC : Incorrect value
CR : Correct value
Add : Address

SACD Water Mark Check

 PSP AMP

 PSN

 Start: ENTER

Exit: RETURN

On this screen, measure the PSP AMP value and PSN value of SACD
water mark.

On the Test Mode Menu screen, selecting 

[3]

 executes the aging of

the mechanism deck.

### Aging Test MENU ###

Operation Menu

1. Open/Close Test

Exit: RETURN

1)

On the Aging Test MENU screen, press the 

[1]

  key  on the

remote commander to display the Open/Close Test screen.

2)

Insert discs and press the 

[ENTER]

  key on the remote

commander.

3)

Is starts the aging.
During aging, the disc number, operating status and repeat cycle
are displayed. Aging can be aborted at any time by pressing
the

x

key. After the operation is stopped, press the

x

key or

[RETURN]

 key aging to return to the Aging Test MENU.

On the Test Mode Menu screen, selecting 

[4]

  displays the

information such as servo emergency history.
The history information from last 1 up to 10 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.

### EMG. History ###

  Laser Hours

CD

xxxxhxxm

DVD

xxxxhxxm

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

   Select:1-9

Scroll:UP/DOWN

  (1.Latest EMG.)

Exit: RETURN

xxxxhxxm : The laser on total hours. Data below minutes are

omitted.

a.

: Error number.

bb

: Error code.

xx

: Not used.

• Clearing History Information

Press the 

[DVD DISPLAY]

 and 

[CLEAR]

 keys in this order.

Then both CD and DVD data are cleared.

Press the 

[DVD TOP MENU]

 and 

[CLEAR]

 keys in this order.

Press 

[DVD MENU]

 and 

[CLEAR]

 keys in this order.

The data have been initialized when “Set Up Initialized”
message is displayed. The EMG. History screen will be restored
soon.

22

• Code list of Emergency History

10: Communication to RF AMP (IC001) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Check sum error of EEPROM (IC203).
14: Communication to servo DSP (IC401) failed, or servo DSP

decoder (IC801) is faulty.

15: Communication to DVD decoder (IC701) failed, or DVD

decoder (IC801) is faulty.

16: Communication to DSD decoder (IC801) failed, or DSD

decoder (IC801) is faulty.

20: Initialization of sled servo failed. It is not placed in the ini-

tial position.

23: Sled servo operation error.
24: Made a request to move the sled servo to wrong position.
30: Tracking balance adjustment error.
31: Tracking gain adjustment error.
33: Focus bias adjustment error.
34: Focus gain adjustment error.
35: Equalizer adjustment error.
40: Focus servo does not operate.
41: With a DVD dual layer disc, focus jump failed.
50: CLV (spindle) servo does not operate.
51: Spindle does not stop.
60: Made a request to seek nonexistent address.
61: Seek error of retry more than regulated times.
70: Control data could not be read.
80: Disc reading failed.

On the Test Mode Menu screen, selecting 

[5]

 displays the information

of mechanism deck error history.
The history information from last 1 up to 8 can be scrolled with the

O key or o key. Also, specific information can be displayed by

directly entering that number with ten keys.

### Mecha Error History ###

  1. aa bb cc dd xx xx xx xx

  2. aa bb cc dd xx xx xx xx

  3. aa bb cc dd xx xx xx xx

  4. aa bb cc dd xx xx xx xx

  5. aa bb cc dd xx xx xx xx

  6. aa bb cc dd xx xx xx xx

  7. aa bb cc dd xx xx xx xx

  8. aa bb cc dd xx xx xx xx

Scroll:UP/DOWN

(1.Latest Err.)

Exit: RETURN

aa : The error in the midst of initializing the mechanism deck.
bb : The error in the midst of loading operation.
cc : The error in the midst of up/down the stocker.
dd : The error in the midst of switching the mechanism deck mode.
xx : Not used.

• Error code (aa)

FF : Complete the initializing. (normal operation)
11 : Stocker movement (to chucking position) failing in the midst

of initializing the mechanism deck.

12 : Stocker movement (to chucking position) failing in the midst

of initializing the mechanism deck.

1x : Initializing the mechanism deck.
2x : Initializing the mechanism deck.
3x : Initializing the mechanism deck.
41 : Disc eject failing in the midst of initializing the mechanism

deck.

4x : Initializing the mechanism deck.

50 : Disc eject failing in the midst of initializing the mechanism

deck.

5x : Initializing the mechanism deck.
A2 : Disc eject failing in the midst of initializing the mechanism

deck.

Ax : Initializing the mechanism deck.
D3 : Disc eject failing in the midst of initializing the mechanism

deck.

Dx : Initializing the mechanism deck.
Ex : Initializing the mechanism deck.

•

Error code (bb)

00 : Initializing the mechanism deck.
10 : Retry over of eject and loading.
30 : Open operation in no disc status.
60 : Retry over of eject and loading.
70 : Disc is chucking position.
81 : Retry failed of disc movement from chucking position to

stocker.

83 : Retry preparation failed of disc movement from chucking

position to stocker.

90 : Disc is stored in the stocker.
A1 : Retry failed of disc movement from stocker to chucking

position.

A3 : Retry preparation failed of disc movement from stocker to

chucking position.

B0 : Just before the release operation.
B1 : Retry failed of the release operation.

• Error code (cc)

10 : Under a stop.
22 : Retry preparation failed.
23 : Retry failed.

• Error code (dd)

10 : Under a stop.
22 : Retry preparation failed.
23 : Retry failed.

On the Test Mode Menu screen, selecting 

[6]

 displays the ROM

version and region code.
The parenthesized hexadecimal number in version field is checksum
value of ROM.

## Version Information ##

 IF con.

Ver.x. xx

 SYScon.

Ver.x. xx  (xxxx)

Model

AVD-C70ES

Region

0x

 Front End Ver.x.xx

Exit: RETURN

IF con.

: The version of system controller (IC901).

SYScon. : The version of DVD system processor (IC206).
Front End: The version of mechanism controller (IC301).

On the Test Mode Menu screen, selecting 

[7]

 displays color bars

for video level adjustment. During display of color bars, OSD
disappears but the menu screen will be restored if pressing the

[RETURN]

 key.

23

Pin No.

Pin Name

I/O

Pin Description

1

EEP SO

O

Not used. (Open)

2

SDEN

O

Serial data enable signal output to DVD/CD RF amplifier

3

DOCTRL/

O

Digital out on/off contrrol signal output to the digital signal processor

ISBTEST

“L”: digital out off, “H”: digital out on

4

EEP WC

O

Not used. (Open)

5

EEP SI

I/O

Two-way data bus with the EEPROM

6

EEP RDY

I

EEPROM ready signal input from the DVD decoder

7

FCS JMP 1

O

Focus jump 1 signal output to the motor/coil driver

8

FCS JMP 2

O

Focus jump 2 signal output to the motor/coil driver

9

SENS CD

I

Internal status (SENSE) signal input from the digital signal processor

10

LOAD +

O

Loading motor drive signal (loading in direction) output terminal    Not used. (Open)

11

LOAD –

O

Loading motor drive signal (loading out direction) output terminal    Not used. (Open)

12

XCS DVD

O

Chip select signal output to the DVD decoder

13

VSS

—

Ground terminal (digital system)

14 to 21

D0 to D7

I/O

Two-way data bus with the DVD decoder

22

INIT0 DVD

I

Interrupt signal input from the DVD decoder

23

INIT1 DVD

I

Interrupt signal input from the DVD decoder

24

FCOMP H

O

Serial data transfer clock signal output to the DSD decoder

25

FCOMP L

O

Reset signal output to the DVD decoder    “L”: reset

26

SCOR

I

Subcode sync (S0+S1) detection signal input from the digital signal processor

27

LAT CD

O

Serial data latch pulse signal output to the digital signal processor

28

LD ON

O

Laser diode on/off control signal output to the DVD/CD RF amplifier

“L”: laser diode off, “H”: laser diode on

29

MIRR

I

Mirror signal input from the digital signal processor

30

COUT CD

I

Numbers of track counted signal input from the digital signal processor

31

INLIM

I

Detection signal input from limit in switch

The optical pick-up is inner position when “H”

32

CS ZIVA

O

Chip select signal output to the DVD system processor

33

SI ZIVA

I

Serial data input from the DVD system processor

34

SO ZIVA

O

Serial data output to the DVD system processor

35

SCK ZIVA

O

Serial data transfer clock signal output to the DVD system processor

36

DRVIRQ

O

Interrupt request signal output to the DVD system processor

37

DRVRDY

O

Ready signal output to the DVD system processor

38

RST

I

System reset signal input from the DVD system processor    “L”: reset

39

VSS

—

Ground terminal (digital system)

40

XTAL

I

System clock input terminal (20 MHz)

41

EXTAL

O

System clock output terminal (20 MHz)

42

VDD

—

Power supply terminal (+3.3 V) (digital system)

43, 44

SLED A, SLED B

O

Sled motor drive signal output

45

SCK DSD

O

Output terminal for offset adjustment of APEO

46

SDOUT DSD

O

Serial data output to the DSD decoder

47

SDIN DSD

I

Serial data input from the DSD decoder

48

READY DSD

I

Ready signal input from the DSD decoder    “L”: ready

49

DATA CD

O

Serial data output to the digital signal processor

50

CLOK CD

O

Serial data transfer clock signal output to the digital signal processor

51

XMSLAT

O

Serial data latch pulse signal output to the DSD decoder

52

SQSO

I

Subcode Q data input from the digital signal processor

24

Pin No.

Pin Name

I/O

Pin Description

53

MUTE DSD

O

Muting on/off control signal output to the DSD decoder    “H”: muting on

54

SQCK

O

Subcode Q data reading clock signal output to the digital signal processor

55

VSS

—

Ground terminal (digital system)

56

TRAY IN

I

Disc tray in detection signal input terminal    Not used. (Fixed at “L” in this set.)

57

TRAY OUT

I

Disc tray out detection signal input terminal    Not used. (Fixed at “L” in this set.)

58

GFS DVD

I

Guard frame sync signal input from the DVD decoder

59

MUTE CD

O

Muting on/off control signal output to the digital signal processor    “H”: muting on

60

MUTE 2D

O

Muting on/off control signal output to the motor/coil driver    “H”: muting on

61

SLED

I

Sled motor servo drive PWM signal input terminal

62

FG

I

Spindle motor control signal input

63

SP ON

O

Muting on/off control signal output to the motor/coil driver    “H”: muting on

64

JIT

I

Jitter signal input

65

TE

I

Tracking error signal input from the DVD/CD RF amplifier

66

PI

I

Pull in signal input from the DVD/CD RF amplifier

67

FE

I

Focus error signal input from the DVD/CD RF amplifier

68

AVSS

—

Ground terminal (for A/D converter)

69

AVREF

I

Reference voltage input terminal (for A/D converter)

70

AVDD

—

Power supply terminal (+3.3 V) (for A/D converter)

71

GFS CD

I

Guard frame sync signal input from the digital signal processor

72

SCLK CD

O

SENSE serial data reading clock signal output to the digital signal processor

73

TSD M

O

Thermal shut down signal output to the motor/coil driver

74

FOK CD

I

Focus OK signal input from the digital signal processor

75

LOCK CD

I

GFS is sampled by 460 Hz    “H” input when GFS is “H”

76

LDSEL

O

Laser diode selection signal output

77

SACD/DVD

O

SACD/DVD selection signal output    “L”: DVD, “H”: SACD

78

I2C SIO

I/O

Communication data bus with the DVD system processor and system controller

79

I2C SCL

I/O

Communication data reading clock signal input or transfer clock signal output with

the DVD system processor and system controller

80

RXD

I

Serial data input from the RS-232C (for check)

81

TXD

O

Serial data output to the RS-232C (for check)

82

SDCLK RF

O

Serial data transfer clock signal output to the DVD/CD RF amplifier

83

SDATA RF

I/O

Two-way data bus with the DVD/CD RF amplifier

84

XWR

O

Write strobe signal output to the DVD decoder

85

XRD

O

Read strobe signal output to the DVD decoder

86

(PWE)

—

Not used.

87

VDD

—

Power supply terminal (+3.3 V) (digital system)

88

VSS

—

Ground terminal (digital system)

89 to 96

A0 to A7

O

Address signal output to the DVD decoder

97

A8

O

Motor/coil driver power save control signal output terminal

98

XDRST

O

Reset signal output to the digital signal processor and DSD decoder    “L”: reset

99

EEP WP

O

Write protect signal output to the EEPROM

100

EEP CLK

O

Clock signal output to the EEPROM