Sony SAL70300G Service Manual ▷ View online
HELP
SAL70300G (4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
HELP
Note for assembling and grease applying positions are shown.
HELP02-01
1.
When installing the fixed barrel assy to the unit, install the fixed barrel assy while drawing the flexible board of stator out of the hole.
2.
Make a folding wrinkle of flexible board of stator as shown in the figure.
HELP02-02
1.
Install the pressurizing plate, facing its convex side to the fine same side.
2.
Install the spring, facing its concave side down and its convex side up.
Note:
When installing the wave washer (SSM assy), be careful for valley part not to overlap the flexible board of stator.
Fixed Barrel Assy
Mountain
Fold
Fold
Valley Hold
Hole
Flexible board
of stator
of stator
Convex Side
Cross
Section
Section
Convex Side
Concave Side
Cross
Section
Section
Valley part
Valley part
Flexible board
of stator
of stator
Fine Same
Wave Washer
(SSM Assy)
(SSM Assy)
Pressurizing
Plate
Plate
Wave Washer
(SSM Assy)
(SSM Assy)
HELP
SAL70300G (4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
HELP02-03
1.
Install the rotor (SSM assy) and then the three pieces of stopper.
Note 1:
Never touch the resin surface (black coated surface).
If you touch it, wipe the resin surface (black coated surface) with waste paper soaked with ethanol.
Note 2:
Due to grease of finger, the function of rotor (SSM assy) will deteriorate, leading to a trouble. To avoid this, wear the finger
sack.
Note 3:
Attach stopper to the hole near the eyepiece side of the body.
2.
Align the flexible board of stator (SSM assy) and the flexible board of Z.ECD flexible board at the positions shown in the figure.
3.
Aligning the stopper with the groove of stator (SSM assy), install the stator (SSM assy).
Note :
Due to grease of finger, the function of stator (SSM assy) will deteriorate, leading to a trouble. To avoid this, wear the finger
sack.
Resin Surface
(Black Coated Surface)
(Black Coated Surface)
Rotor (SSM Assy)
Never touch the resin surface
Rotor (SSM Assy)
Stopper
Stopper
Stator (SSM Assy)
Never touch the slip surface
Slip Surface
Flexible Board
(Z.ECD Flexible Board)
(Z.ECD Flexible Board)
Flexible Board
Stator (SSM Assy)
Stopper
Stopper
HELP
SAL70300G (4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
HELP02-04
1.
Rotating the focus ring in the arrow direction, align the cut portion with the 1st-F linkage pin insertion groove.
2.
Aligning the 1st-F linkage pin insertion hole of rotary barrel assy with the 1st-F linkage pin insertion groove, install the rotary barrel
assy.
Note:
Since the 1st-F linkage pin insertion hole is not 180
°
symmetry, be careful of the direction of assembling.
3.
Make pairs of two pieces of 1st-F linkage pin and two pieces of 1st-F linkage coma and install them to the rotary barrel assy.
Note:
Assemble them until the 1st-F linkage coma engages with the 1st-F linkage pin insertion groove.
4.
Confirm the action of rotary barrel assy.
Rotary Barrel Assy
1st-F Linkage Pin Insertion Groove
Since the 1st-F linkage pin insertion hole
is not 180˚ symmetry, be careful of
the direction of assembling.
is not 180˚ symmetry, be careful of
the direction of assembling.
1st-F Linkage Pin
Insertion Groove
Insertion Groove
Focus Ring
1st-F Linkage Pin Insertion Hole
Notch
Focus Ring
Rotary Barrel Assy
1st-F Linkage Coma
1st-F Linkage Coma
1st-F Linkage Pin
1st-F Linkage Pin
1st-F Linkage Pin
Insertion Hole
Insertion Hole
1st-F Linkage
Coma
Coma
HELP
SAL70300G (4.5-5.6/70-300 G SSM) (70-300mm F4.5-5.6 G SSM)
HELP02-05
Grease (G-36): J-6082-667-A
Grease (G-48): J-6082-669-A
1.
Apply the Grease (G-36) and (G-48) to the indicated portions of MF connect barrel A.
2.
Install the MF connect barrel A, aligning three locations of groove A of MF connect barrel A with three locations of convex A of
focus ring.
MF Connect Barrel A
MF Connect Barrel A
Groove A
Groove A
Groove A
MF Connect Barrel A
Apply the grease (G-36)
(Both side)
(Both side)
Apply the grease (G-48)
(Three locations of groove A)
(Three locations of groove A)
MF Connect Barrel A
Groove A
Groove A
Groove A
Convex A
Convex A
Convex A
Focus ring
Click on the first or last page to see other SAL70300G service manuals if exist.