Sony SAL70200G (serv.man2) Service Manual ▷ View online
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP46
Adhesive bond (B-40):
J-6082-614-A
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or the equivalent
Do not use the instant glue that becomes white when dried.
Grease (G-85):
J-6082-626-A
1.
Install the rear light shield barrel to the mount and tighten it with four screws to which tips two drops of adhesive bond (B-40) are
applied.
2.
Apply two drops of adhesive bond (LOCKTITE 460) to the tip of stopper screw and tighten the stopper screw.
3.
Apply the grease (G-85) to the indicated portion of mount.
4.
Install the lens mount block to the outside barrel, apply two drops of adhesive bond (LOCTITE 460) to the tips of four screws and
tighten the screws.
Note:
Fix the flexible BL PWB and lead wires to the grooves of outside barrel at two locations, threading through the outer
diameter. And fix them with two polyester tapes (black) 10mm.
Apply the adhesive
bond (B-40)
bond (B-40)
Mount
Rear Light
Shield Barrel
Shield Barrel
Apply the adhesive
bond (B-40)
bond (B-40)
Apply the adhesive
bond (B-40)
bond (B-40)
Apply the adhesive
bond (LOCTITE 460)
bond (LOCTITE 460)
Apply the
grease (G-85)
grease (G-85)
Back side of mounting
claw 3 locations
claw 3 locations
Stopper Screw
Outside Barrel
Polyester Tape
(Black) 10mm
(10X50mm)
(Black) 10mm
(10X50mm)
Polyester Tape
(Black) 10mm
(10X50mm)
(Black) 10mm
(10X50mm)
Lead wires
Flexible BL
PWB
PWB
Groove
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP47
1.
Route the lead wires along the shape of Flexible BL PWB and fix it with the polyester tape (black) 4mm.
2.
Solder the lead wire (yellow) to the indicated portion of Flexible BL PWB.
3.
Insulate the indicated portion of Flexible BL PWB.
Note:
If the width of polyester tape is not enough, use two sheets of polyester tape.
Lead Wire (Red)
Lead Wire (Black)
Flexible BL PWB
Flexible BL PWB
Soldering
Lead Wire
(Yellow)
(Yellow)
Polyester Tape
(Black) 4mm
(4X15mm)
(Black) 4mm
(4X15mm)
Polyester Tape
(Black) 4mm
(4X15mm)
(Black) 4mm
(4X15mm)
Polyester Tape
(12X30mm)
(12X30mm)
Polyester Tape
(12X30mm)
(12X30mm)
Signal Box Block
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP48
Adhesive bond (B-10): J-6082-612-A
Install the main spring hook to the outside barrel, install the main spring as shown in the figure and apply the adhesive bond (B-10).
HELP49
Adhesive bond (B-40): J-6082-614-A
Assemble the aperture connect lever in the preset ring, apply two drops of adhesive bond (B-40) to the tips of screws, tighten it with the
screws.
Note:
Install the aperture connect lever and the preset ring so that they cross each other perpendicularly.
If the aperture connect lever leans, the aperture trouble (The blade remains.) occurs.
Apply the adhesive
bond (B-10)
bond (B-10)
Apply the adhesive
bond (B-10)
bond (B-10)
Apply the adhesive
bond (B-10)
bond (B-10)
Main Spring
Hook
Hook
Main Spring
Main Spring
Outside Barrel
Outside Barrel
Aperture Connect
Lever
Lever
Aperture Connect Lever
Aperture Connect Lever
Apply the adhesive
bond (B-40)
bond (B-40)
Preset Ring
Preset Ring
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP50
1.
Install the SW1 shielding rubber and the SW2 shielding rubber, facing the adhesive side (ribbon-affixed side) to the SW1 and SW2.
2.
Install the click plate so that the side of vestige of eject pin faces toward you.
SW1 Shielding
Rubber
Rubber
SW1 Shielding
Rubber
Rubber
SW2
Shielding
Rubber
Shielding
Rubber
SW1
SW1
Switch Cover
SW2
Install them, facing
the adhesive sides
(ribbon-affixed side)
to SW1 and SW2
the adhesive sides
(ribbon-affixed side)
to SW1 and SW2
Install the SW1 shielding
rubber, facing the
ribbon-affixed side to SW1.
rubber, facing the
ribbon-affixed side to SW1.
Click Plate
Vestige of eject pin
Vestige of eject pin
Click on the first or last page to see other SAL70200G (serv.man2) service manuals if exist.