Sony SAL35F14G Service Manual ▷ View online
4-17
SAL35F14G (1.4/35G) (35mm F1.4G)
2. Adjusting Method
1)
Move the preset ring and fix it at the fully opened position.
Fig.4-2-10
2)
Adjust by rotating the aperture holding ring so that the blades of iris are just hidden within the inner diameter of aperture holding
ring.
Fig.4-2-11
3)
After adjustment, apply the adhesive bond (B-10) to portions shown in Fig.4-2-9.
Note:
Affer apply the adhesive bond (B-10), please leave it for 6 hours or more.
4)
Assemble the lens in the state of near completion. Perform “4-2-1. Confirmation of iris diameter”.
Note:
Repeat “4-2-2. Adjustment of iris diameter” and “4-2-1. Confirmation of iris diameter” until the iris tolerance meets the specifica-
tion.
Set the preset ring at the open aperture position.
Preset lever
Aperture blades are hidden into the
edge completely.
edge completely.
4-18
SAL35F14G (1.4/35G) (35mm F1.4G)
4-3.
PROJECTIVE RESOLVING POWER CHECK
Equipment
• Lens Test Projector and Variable Transformer (Output voltage: AC 100 V)
Note:
Connect the variable transformer (Output voltage: AC 100 V) to the lens test projector.
• A-mount Attachment
• Screen (Art paper)
• Tape Measure
• Plane Mirror (For SLRs)
1. Preparations
Note:
Note:
Check the projective resolving power of the checking lens at the following focal-length and distance.
Focal-length
Distance (m)
f (mm)
35
1.4
Table 4-3-1
1)
Perform the following steps (1) to (3), and incorporate the internal lenses of the lens test projector according to the checking focal-
length.
(1) Open the lid of the lens test projector.
(2) Pull up and turn the fixed levers on the right and left sides of the lens test projector.
(3) Remove or insert the lens.
Note:
Be sure to have the right position and direction of the lens.
Fig.4-3-1
Lens test projector
Incorporate of the lenses
according to the checking focal-length (f).
according to the checking focal-length (f).
Lens
Fixed lever
Fixed lever
Lid
f=18 to 35 mm
f=35 to 100 mm
f=100 to 200 mm
f=200 to 300 mm
Heat-absorbing filter
Chart
Chart
Chart
Chart
Filament
Filament
Filament
Filament
Ver 1.1 2007.02
4-19
SAL35F14G (1.4/35G) (35mm F1.4G)
2)
Attach the checking lens to the lens test projector, and set the equipments as shown in Fig.4-3-2.
3)
Turn the fan switch of the lens test projector to ON, then turn the lamp switch to ON.
Fig.4-3-2
4)
Turn the focus ring of the checking lens until the chart image projected on the screen is the sharpest at the center (y’=0).
5)
Set the plane mirror to the center of the projected image (y’= 0), and adjust the projector position so that the mirror reflects the light
to the center of the lens.
Distance
Lens test projector
Chart
Fan switch
Lamp switch
Plane mirror
Screen
A-mount attachment
Checking lens
F
L
4-20
SAL35F14G (1.4/35G) (35mm F1.4G)
2. Checking Method
1)
Turn the focus ring of the checking lens until the chart image projected on the screen is the sharpest at the center (y’=0).
2)
Read the number of the smallest pitched lines at the center (y’= 0).
Fig.4-3-3
3)
Turn the mount rotation ring of lens test projector until the projected image at a certain peripheral point (y’= 15) on the screen
appears the most unsharp.
Read the number of the smallest pitched lines (both saggital and meridional: 3 lines) at the peripheral point.
Note:
When reading the number of the smallest pitched lines, be careful of the spurious resolution.
Spurious resolution is the reversed image of 2 or 4 lines which appears on screen when focus is beyond maximum revolving
power.
Do not confuse spurious resolution for the smallest pitched lines.
Fig.4-3-4
4)
Check that the all readings (y’= 0, saggital (S) and meridional (M) at y’= 15) is within the specification of the Table 4-3-2.
Specification
Number of the smallest pitched lines
Distance (m)
Center (y’= 0)
Peripheral (y’= 15)
(Lines per mm)
(Lines per mm)
S
M
1.4
125 or greater
50 or greater
40 or greater
Table 4-3-2
5)
After the checking is completed, turn the lamp switch of the lens test projector to OFF and cool the inside of the lens test projector,
then turn the fan switch to OFF.
The number represents for lines per mm.
Saggital (S)
Meridional (M)
Correct resolution
Spurious resolution
Ver 1.1 2007.02
Click on the first or last page to see other SAL35F14G service manuals if exist.