Sony SAL300F28G Service Manual ▷ View online
5-9
SAL300F28G (2.8/300 G) (300mm F2.8 G)
4. Setting procedure using the SSM half completion JIG
After confirming the PC card setting, continue the steps.
1)
Connect the USB cable (white) leading from the SSM half completion JIG to the PC.
2)
It can be automatically used.
3)
Start up [Instacal]. (See page 5-8.)
4)
The menu below appears. Confirm that [USB-1208**] is checked and then click [OK].
Note:
“**” may change.
Fig.5-1-19
5)
When the menu below appears, confirm that [PC-CARD-DI048] is displayed in [Board#0] and [USB-1208**] is displayed in
[Board#1].
Note:
If they are reversed, the adjustment program does not start up.
Fig.5-1-20
6)
Click [Board#1] to highlight it blue. Then, click the set button at third position from left on the top row.
Fig.5-1-21
5-10
SAL300F28G (2.8/300 G) (300mm F2.8 G)
7)
Change [No. of channels] to [8 Single Ended].
Fig.5-1-22
8)
Click [OK] and close the menu by clicking its [x].
Note:
Do not change the positions to insert the DIO card and USB cable.
5. Startup of Lens Adjustment Program (ActuatorChecker.exe)
1)
Download the file “ActuatorChecker VerX.X.X.X.zip” from Service Fixture and Software of ESI homepage, save and extract it.
2)
Start up “ActuatorChecker.exe” from an arbitrary folder.
3)
If “PC-CARD-DIO48” is properly installed, the window below appears.
Note:
The version of “ActuatorCheker” might be updated.
• Final
• Half
Fig.5-1-23
Fig.5-1-24
5-11
SAL300F28G (2.8/300 G) (300mm F2.8 G)
5-1-3. Connection of Finished Inspection JIG/SSM Half Completion JIG and Lens Adjustment
Program (ActuatorChecker)
Note:
Confirm “5-1-2. Lens Adjustment Program (ActuatorChecker)” has been completed before this procedure is executed.
In case of performing Finished inspection or Half completion inspection, be sure to perform in the condition the lens is laid down
(do not perform in the lens standing condition).
Equipment
• Personal Computer
• Finished Inspection JIG (AC100 V only)
• Lens Adjustment Program (ActuatorChecker.exe)
• SSM Half Completion JIG (At half completion inspection)
1.
Connect equipment and checking lens as shown Fig.5-1-25 or Fig.5-1-26.
• Final
Fig.5-1-25
• Half
Fig.5-1-26
2.
Turn on the finished inspection JIG.
3.
Turn on the personal computer.
4.
Start up “ActuatorChecker.exe” from an arbitrary folder, conform that start up program normally.
Note:
Turn off the finished inspection jig after use.
Finished Inspection JIG
Lens
Lens
Finished Inspection JIG
Harness (Black)
Harness (Blue)
Harness (Yellow)
MR Sensor Block(7 pin)
DV Encoder Flexible(12 pin)
SSM Half Completion JIG
5-12
SAL300F28G (2.8/300 G) (300mm F2.8 G)
5-1-4. Initial Setting of “ActuatorChecker”
1.
Start up “ActuatorChecker.exe”.
Fig.5-1-27
2.
Depending on the initial startup or setting made at the previous startup, the window differs.When the Japanese window appears, click
the
[Set up]
button, change the language to English.
Note:
When any button is clicked, the Serial window appears. The window to enter the lens serial number appears.
Fig.5-1-28
Fig.5-1-29
Click on the first or last page to see other SAL300F28G service manuals if exist.