Sony SAL300F28G Service Manual ▷ View online
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP12
Cut two polyester tapes in 30mm to make the size of 12 x 30mm and affix them to position shown in the figure below to fix the SW
connection FPC block.
HELP13
Cut four polyester tapes in 30mm length. Affix two sheets of polyester tape o cove the area of 12 x 30mm at each location as shown below
to fix the flexible cards to the board.
DM PC Board Unit
SW Connection FPC Block
30mm
12mm
Polyester Tape
(9X30mm)
(9X30mm)
Polyester Tape
(9X30mm)
(9X30mm)
Polyester Tape
(9X30mm)
(9X30mm)
Polyester Tape
(9X30mm)
(9X30mm)
DC-DC PC Board Block
MM PC Board Unit
30mm
12
mm
DM PC Board Unit
Polyester Tape
(9X30mm)
(9X30mm)
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP14
Connect the MM pc board unit and the DC-DC pc board block with the connection flexible (B) block.
Note:
Align the triangle mark of DC-DC pc board block with the triangle mark of connection flexible (B) block.
DC-DC PC
Board Block
Board Block
DC-DC PC
Board Block
Board Block
Triangle mark
MM PC
Board Unit
Board Unit
Connection Flexible (B) Block
Connection Flexible (B) Block
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP15
Adhesive bond (B-40): A-6082-614-A
1.
Bridge-solder the harness (pink) leading from the connection box block to two leads of IC (See the figure below) on the DC-DC pc
board block (B side).
2.
Apply two drops of adhesive bond (B-40) to the tips of two screws.
3.
Fix the DC-DC pc board block with two screws.
4.
Solder two harnesses (black/red) leading from the connection box block and three harnesses (blue/black/yellow) to the DC-DC pc
board block (A side).
Harness (Pink)
(From the connection
box block)
(From the connection
box block)
Harness (Pink)
(From the connection
box block)
(From the connection
box block)
Harness (Red)
Harness (Black)
Harness (Black)
Harness (Blue)
Harness (Yellow)
(From the
connection
box block)
connection
box block)
(From the stator)
Bridge-solder two leads of IC.
DC-DC
PC Board
Block
PC Board
Block
DC-DC
PC Board
Block
PC Board
Block
DC-DC PC Board Block
(Side A)
DC-DC PC Board Block
(Side B)
Apply the adhesive
bond (B-40)
bond (B-40)
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP16
Cut the polyester tape in 30mm length and affix it to the indicated portion of aperture inner barrel.
HELP17
Adhesive bond (B-40): J-6082-614-A
1.
Install the aperture inner barrel, aligning the flexible card freeing part of connect barrel with the flexible card freeing part of aperture
inner barrel block.
Note:
Draw out the flexible cards of DV encoder flaxible and MR connection flaxible from the flexible card freeing part of
aperture inner barrel.
2.
Apply two drops of adhesive bond (B-40) to the tips of six screws and tighten the aperture inner barrel with six screws.
Cut hole
Cut hole
Aperture Inner
Barrel
Barrel
Polyester Tape
9mm (9X30mm)
9mm (9X30mm)
Polyester Tape
9mm (9X30mm)
9mm (9X30mm)
30mm
9mm
Apply the adhesive
bond (B-40)
bond (B-40)
Apply the adhesive
bond (B-40)
bond (B-40)
Aperture Inner Barel
Block
Block
Aperture Inner Barel
Flexible card
freeing part
freeing part
Flexible card
freeing part
freeing part
MR Connection
Flaxible
Flaxible
MR Connection
Flaxible
Flaxible
DV Encoder Flaxible
DV Encoder
Flaxible
Flaxible
Connect Barrel
Click on the first or last page to see other SAL300F28G service manuals if exist.