Sony SAL24105 Service Manual ▷ View online
4-30
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
4-9.
ZOOM BRUSH POSITION CHECK/ADJUSTMENT AND PATTERN CHECK
4-9-1. Zoom Brush Position Adjustment (Search Zoom Adjustment Point)
Equipment
• Personal Computer (PC)
• Finished Inspection JIG (AC100 V only)
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Remove the zoom rubber ring.
Fig.4-9-1
2)
Peel off the polyester tape (black) 10 mm and remove the zoom ring reinforcement plate and brush cover.
Fig.4-9-2
3)
Connected to equipment with checking lens. (Refer to Section 4-1-3.)
4)
Start up of “ActuatorChecker.exe”.
5)
Click
[Set up]
, and perform the initial setting. (Refer to Section 4-1-4.)
Zoom Rubber Ring
Brush Cover
Polyester Tape (Black) 10mm
(8x25 mm)
(8x25 mm)
Polyester Tape (Black) 10mm
(8x25 mm)
(8x25 mm)
Zoom Ring Reinforcement Plate
Zoom Ring
4-31
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
2. Adjusting Method
1)
Set the zoom to “Tele end”.
2)
Peel off the polyester tape (black) 10 mm.
Fig.4-9-3
3)
Click the
[Search Zoom Adj Point].
Fig.4-9-4
Note:
Move the brush right and left to adjust. At this moment, be careful not to shift the position by shock when touching to the
zoom.
Fig.4-9-5
Flexible Board (Pattern (trace) Side)
Zoom Brush
Zoom Brush
Zoom Ring
Zoom Brush
Polyester Tape (Black) 10 mm
(6x50 mm)
(6x50 mm)
4-32
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
4)
The message “If Zoom-Adjustment-Point is found, Buzzer sounds”. is displayed on the pop-up window.
Search the position where the sound beeps by turning the lens to the infinity position.
Fig.4-9-6
5)
Fix firmly the zoom brush with the polyester tape (black) 10 mm as shown in Fig. 4-9-7.
6)
Perform “4-9-2. Zoom Brush Position Check” and “4-9-3. Zoom Brush Pattern Check”
3. In case of error display in the Search Focus Adjustment Point
1)
When the error display and the NG display appear to the pop-up window, press the ENTER key to return to the initial window, and
perform “2. Adjusting Method”again.
Fig.4-9-7
Fig.4-9-8
2)
If the “NG” appears again, thought cause communication error of the finished inspection JIG and checking lens, confirm or perform
the following.
• Improper connection of connector.
• Improper of BL contact.
• Disconnection of mirror box fixture.
4-33
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
4-9-2. Zoom Brush Position Check (Zoom Adjustment Point)
Equipment
• Personal Computer
• Finished Inspection JIG (AC100 V only)
• Lens Adjustment Program (ActuatorChecker.exe)
1. Preparations
1)
Connected to equipment with checking lens. (Refer to Section 4-1-3.)
2)
Start up of “ActuatorChecker.exe”.
3)
Click
[Set up]
, and perform the initial setting. (Refer to Section 4-1-4.)
2. Checking Method
1)
Click the
[Zoom Adjustment Point]
.
Fig.4-9-9
2)
The Serial window appears. Input the lens serial number.
Note:
When
[OK]
is clicked without inputting the serial number, the date executed is displayed on the completion window of each
item.
Fig.4-9-10
3)
The message “Move ZOOM to WIDE position. Then push [ENTER].” is displayed on the pop-up window.
Set the zoom to the wide position and press down the ENTER key.
Fig.4-9-11
Click on the first or last page to see other SAL24105 service manuals if exist.