Sony SAL20TC Service Manual ▷ View online
HELP
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
HELP09
Grease (G-35):
J-6082-621-A
Grease (G-85):
J-6082-626-A
Adhesive bond (B-40): J-6082-614-A
1.
Aplly the grease (G-35) and (G-85) to the gear base block.
2.
Apply the adhesive bond (B-40) to four screws in figure.
HELP10
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to the instruction part of the four screws.
HELP11
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to the instruction part of the two screws in figure.
Apply the grease (G-35)
Apply the grease (G-85)
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Fixed Barrel
Apply the adhesive bond (B-40)
Ground Spring A
BL Contact Holding Block
HELP
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
HELP12
Grease (G-85):
J-6082-626-A
Adhesive bond (B-40): J-6082-614-A
1.
Apply the grease (G-85) to the instruction part of the lock pin.
2.
Apply the adhesive bond (B-40) to the screw that unites lock pin with lock release lever.
HELP13
Grease (G-85): J-6082-626-A
Apply the grease (G-85) to the instruction part of the lever base plate unit.
HELP14
Grease (G-85): J-6082-626-A
Apply the grease (G-85) to the instruction part of the lock holding lever block.
Lock Release Lever
Apply the grease (G-85)
(All circumference of threaded portion))
(All circumference of threaded portion))
Lock Pin
Apply the adhesive bond (B-40)
Apply the grease (G-85)
Lever Base Plate Unit
Apply the grease(G-85)
(All circumerence of threaded portion)
(All circumerence of threaded portion)
Lock Holding Lever Block
HELP
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
HELP15
Adhesive bond (B-10): J-6082-612-A
1.
Stick the tape (such as scotch tape) onto the Preset ring.
2.
Stick it to be positioned at the center of the connect ring. (The space should be the same intervals)
3.
To stabilize the preset ring, add the tape on one or two parts, and assemble the steel balls in order of two steel balls, retainer, and then
one steel ball.
4.
Tighten the preset ring holding plate until it stops lightly.
(Be noted that it is sometimes hard to tighten due to adhesive.)
5.
Remove the tape and loosen the preset ring pressure until the preset ring turns ightly. (about 45 degrees)
6.
Apply the adhesive bond (B-10) at the two parts of the preset ring holding plate.
HELP16
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to the screw in figure.
Apply the adhesive bond (B-10)
Apply the adhesive bond (B-10)
Retainer
Tape
Preset Ring Holding Plate
Steel Ball
Preset Ring
Connect Ring
Body A Mount
Screw Nut
Apply the adhesive bond (B-40)
Ver 1.1 2007.01
HELP
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
HELP17
Adhesive bond (LOCTITE 460)
Note:
Use adhesive bond (LOCTITE 460) or an equivalent aeticle.
Don’t use what becomes white after drying like a quick-drying giue.
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the adhesive bond (LOCTITE 460) to the stopper screw and tighten it.
2.
Apply the anti-diffusion (A-20) to the instruction part of the lens mount block.
3.
Four screws that installs lens mount block tighten in numberical order shown in the figure.
HELP18
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the anti-diffusion agent (A-20) to the instrction part of the fixed barrel.
2.
BL contact holder block and ground spring A are put and after building in, protector rubber is installed in fixed barrel.
Note:
Be careful not to damage A part of fixed tube.
HELP19
It is done up that the point of lock spring is thin.
Apply the anti-diffusion agent (A-20)
Fixed Barrel
Protector Rubber
A part
Apply the anti-diffusion agent (A-20)
(All circumference of threaded portion)
(All circumference of threaded portion)
Apply the adhesive bond (LOCTITE 460)
1
2
3
4
Coupler Hole
Lock Spring
Connect Ring
Click on the first or last page to see other SAL20TC service manuals if exist.