Sony SAL1680Z Service Manual ▷ View online
2-1
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
2. DISASSEMBLY
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
When top of tip does not reach holes or notches because the fixed
screw becomes obstructive, replace the fixed screw to below.
+B 3X5 7-682-546-09
screw becomes obstructive, replace the fixed screw to below.
+B 3X5 7-682-546-09
2-2
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
2-1.
DISASSEMBLY
2-1-1. LENS BLOCK
EXPLODED VIEW
1 Focus Rubber Ring
3 1st Lens Block
2 Front Decoration
Plate
Plate
5 2nd Lens Block
0 3rd Lens Block
8 4th Lens Block
6 Light Shield Plate B
7 Aperture Hold Ring
9 3-4 Adjustment Washer
4 Light Shield Plate A
HELP01
(See page 2-3.)
• About the front decoration plate :
Be sure avoiding replacement of front decoration
plate as far as possible. If replacement of it should
be need, you convey the message to your user
that changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user's
agreement, and it replace.
Be sure avoiding replacement of front decoration
plate as far as possible. If replacement of it should
be need, you convey the message to your user
that changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user's
agreement, and it replace.
Note:
• Remove the 3rd Lens Block :
After replacing the fixed screw of universal
wrench, remove the lens block using the
universal wrench.
After replacing the fixed screw of universal
wrench, remove the lens block using the
universal wrench.
Note:
2-3
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
2-1-2. ZOOM BRUSH, ZOOM BARREL AND OUTER COVER BLOCK
EXPLODED VIEW
9 Outer Cover Block
HELP09
8 Rotation Cover Pin
HELP08
7 Zoom Barrel
HELP07
6 Zoom Hold Ring
HELP06
1 Zoom Rubber Ring
3 Brush Cover (B)
HELP04
2 Brush Cover
HELP03
4 Brush Cover (C)
HELP04
Flex Setting Tape B
HELP02
5 Zoom Brush
HELP05
(See page 2-4.)
ZOOM BRUSH
POSITION
ADJUSTMENT
POSITION
ADJUSTMENT
Polyester Tape
2-4
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
2-1-3. LENS MOUNT BLOCK
EXPLODED VIEW
HELP13
HELP11
HELP12
(See page 2-5.)
HELP14
9 Coupler Adjustment Washer
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
7 Gear C.D Block
8 Coupler Bush
6 AF Coupler
Stopper Screw
2 Ground Spring
1 Main Flexible Unit
HELP10
3 Rear Light Shield Barrel
4 Lens Mount Block
Main Spring
Presetting Holder
5 Back Adjustment
Washer
Washer
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
Presetting Ring Block
Click on the first or last page to see other SAL1680Z service manuals if exist.