Sony SAL1635Z Service Manual ▷ View online
4-18
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
5)
Apply the adhesive bond (B-10) to the head of screw as shown in Fig.4-7-10.
Fig.4-7-10
6)
Rotate the focus from
∞ (infinity) end to near end and then from near end to ∞ (infinity) end to confirm the focus brush position once
again.
3. In case error message appears in the Adjust Focus Brush
1)
Even though the focus locates at the
∞ (infinity) end, if the pop-up window shown below appears, adjust the brush position to search
the focus adjustment point.
Fig.4-7-11
2)
Perform “2. Adjustment/Inspection Method” again.
3)
After adjustment, apply the adhesive bond (B-10) to the head of screw.
4)
Set to the
∞ (infinity) end again by moving the focus barrel to the near end side and check that focus adjustment point is not shifted.
(Repeat twice or more.)
5)
Press the ENTER key or left-click the message display area in the menu with mouse to finish the inspection.
4-7-6. Motor Build-in
1. Preparations
Set to “4-7-5. Focus Brush Position Check/Adjustment” 1. Preparations.
2. Checking Method
1)
Click [Motor Build-in].
2)
Input the numerals (uppermost 3 digits) written on the SSM flexible board.
Fig.4-7-12
Fig.4-7-13
Apply the adhesive
bond (B-10).
bond (B-10).
Brush
Ver. 1.2 2009.03
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
4-19
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
4-8
.
FINISHED INSPECTION (ActuatorChecker)
Equipment
• Personal Computer
• Finished Inspection JIG (AC100V only)
• Lens Adjustment Program (ActuatorChecker)
• Adhesive Bond (B-10)
4-8-1. Preparations
1.
Attach the checking lens to the equipment. (Refer to LENS GENERAL ADJUSTMENT GUIDE Section 1-2. Fig. 1-2-1.)
2.
Start up the lens adjustment program (ActuatorChecker).
3.
Click “Set up” and perform the initial setting. (Refer to LENS GENERAL ADJUSTMENT GUIDE Section 1-3.)
4-8-2. Finished Inspection Item
1. Adjustment/Inspection Method
1)
Click [START].
2)
Operate as instructed in the menu.
2. Inspection Item
1)
Adjust Zoom Brush
2)
ROM Data
3)
Focus Hold Button
4)
AF/MF Switch
5)
CPU Mode Standby Current
6)
Focus Adjustment Point
7)
Focus Pattern (Servo)
8)
Focus Pattern
9)
Zoom Adjustment Point
10) Zoom Pattern
11) FLASH Initialize
12) MR D/A Offset Adj (Manual)
13) Motor Control Coefficient Adj (1)
14) MR D/A Offset Adj (Motor)
15) Dv Pulse
16) Motor Control Coefficient Adj (2)
17) Focus Drive
18) Write dSB
19) Write WB
20) Search Zoom Adj Point
21) Search Focus Adj Point
Note:
This two items are not adjusted automatically in case of starting Adjustment/Inspection with clicking [START].
Fig.4-8-1
Ver. 1.1 2009.02
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
4-20
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
4-8-3. Zoom Brush Position Check/Adjustment
1. Preparations
1)
Remove the zoom rubber ring.
2)
Peel the polyester tape and remove the SUS sheet A.
Fig.4-8-
2
2. Adjustment/Inspection Method
1)
Click [START !Ent?] or [Adjust Zoom Brush].
2)
Operate as instructed in the menu.
Fig.4-8-
3
Zoom Rubber Ring
SUS Sheet A
Polyester Tape
(Black) 10mm
(Black) 10mm
Ver. 1.1 2009.02
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
4-21
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
3)
Set the zoom to the TELE end.
Fig.4-8-
4
Brush
Apply the adhesive bond (B-10)
(After adjustment)
(After adjustment)
4)
When the zoom locates on the zoom adjustment end, the pop-up window shown below appears. At this moment, tighten the screw to
fix the brush.
Fig.4-8-
5
5)
Apply the adhesive bond (B-10) to the head of screw as shown in Fig.
4-8-4
.
6)
Set to the TELE end or WIDE end again and check that the zoom adjustment point is not shifted.
3. In case error message appears in the Adjust Zoom Brush
1)
Even if the zoom locates at the TELE end, if the pop-up window shown below appears, adjust the brush position to search the zoom
adjustment point.
2)
Perform “2.
Adjustment/Inspection Method
” again.
Fig.4-8-
6
3)
After adjustment, apply the adhesive bond (B-10) to the head of screw.
4)
Set to the TELE end again by moving the zoom barrel to the WIDE side and check that zoom adjustment point is not shifted.
(Repeat twice.)
5)
Press the ENTER key or left-click the message display area in the menu with mouse to finish the inspection.
Ver. 1.1 2009.02
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Click on the first or last page to see other SAL1635Z service manuals if exist.