Sony SAL135F18Z Service Manual ▷ View online
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
2.
Put the F-ECD flexible board through the oblong hole of focus hold barrel block.
3.
Align the positioning pin of length grove barrel assy to the pin hole of focus hold barrel block.
4.
Install it with rotating the torque ring A of focus hold barrel block.
Note:
Align the stopper of focus 1 cam ring assy with the cam joint ring of focus hold barrel block.
5.
Tightening four screws (white) (screws 1 to 4 in figure) and five screws (black) (screws 1 to 4 in figure) in orders shown in figure,
fix the outer barrel block to the length grove barrel assy.
6.
Apply the adhesive bond (B-10) to the heads of nine screws.
7.
Perform the torque ring play adjustment. (Refer to 4-6.)
Screw (Black)
Apply the adhesive bond (B-10)
Apply the adhesive bond (B-10)
Screw (White)
Apply the adhesive bond (B-10)
Apply the adhesive bond (B-10)
Focus Hold Barrel Block
Pin hole
FH Button Mail Flexible
Torque Ring A
Positioning Pin
Oblong hole
F-ECD Flexible
Length Grove Barrel Assy
Stopper
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
HELP13
Adhesive bond (B-10): J-6082-612-A
1.
Install the 1 group lens block to the length grove barrel assy and tighten three hexagon bolts to fix it.
2.
Apply the adhesive bond (B-10) the head of hexagon bolt at the length grove barrel assy side.
Note:
Be careful for the adhesive bond not to seep out to the outer diameter side of length grove barrel assy.
HELP14
Peel off the detached paper from the 2nd ornamental sheet and affix it to the location specified in figure.
2nd Ornamental Sheet
2 Lens Block
Length Grove Barrel Assy
1 Lens Block
Hexagon bolt
(Apply the adhesive bond (B-10) (3 places))
(Apply the adhesive bond (B-10) (3 places))
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
Pattern of F ECD Flexible
Zoom Brush
Zoom Brush
Focus 1 Cam Ring Assy
Screws
Apply the adhesive bond
(B-10)
(B-10)
HELP15
Adhesive bond (B-10): J-6082-612-A
Special driver:
J-6082-654-A
1.
Rotate the focus 1 cam ring assy in the arrow direction to make the infinity end.
2.
Install the zoom brush and tighten two screws to fix it. (Use the special driver: J-6082-654-A)
3.
Confirm that the brush securely contacts the trace on F-ECD flexible and has no bending.
4.
Perform the adjustment of focus brush position. (Refer to 4-8.)
5.
After finishing the position adjustment, apply the adhesive bond (B-10) to the location of screwed portion shown in figure.
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
HELP16
Adhesive bond (B-40): J-6082-614-A
1.
Rotate the focus cam ring assy to allowed direction, set to the near position.
2.
Install the 2 lens block to the length grove barrel assy side. Apply the adhesive bond (B-40) to the screwed portions of 2 roller screws.
Then, fix the 2 group lens block with the 2 roller and the 2 roller screws at three locations.
Note:
Select the 2 roller with a play of 0 to 0.010mm with respect to the groove width of length grove barrel assy.
Part Code
Part Name
Diameter
D1
D2
D3
2-897-888-01
2 C roller
3.99
4.50
3.50
2-897-889-01
2 K roller
4.00
4.52
3.50
2-897-890-01
2 L roller
4.01
4.53
3.50
3.
Confirm that the focus 1 cam ring assy rotates smoothly.
D2
D3
D1
2 Lens Block
2 Roller
(3 places)
(3 places)
Focus 1 Cam Ring Assy
2 Roller Screw
(Apply the adhesive bond (B-40) (3 places))
(Apply the adhesive bond (B-40) (3 places))
Click on the first or last page to see other SAL135F18Z service manuals if exist.