DOWNLOAD Sony NEX-7 / NEX-7K (serv.man2) Service Manual ↓ Size: 5.33 MB | Pages: 19 in PDF or view online for FREE

NEX-7/7K_L2

3-1

         Assembly-1:  Screw tightening sequence when assem-

bling the Heat Sink (IM).

1

2

3

Radiation plate (IM)

         Assembly-2:  IM Adjust Washer (A, B, C) putting 
 position.

Cabinet (Front)

         Assembly-3:  Screw tightening sequence when 
 

assembling the MB N Plate A (754).

MB N Plate A (754)

2

1

3

4

         Assembly-4:  Method of attachment of MB Mask Sheet 

(754).

Note: There should not be any misalignment when attaching
          MB Mask Sheet (754).

MB N Plate A (754)

Mask Sheet
Adhesive Sheet

J-6082-735-A

Cabinet Front Block

        Assembly-5:  Apply grease on the MB N Plate SP.

MB N Plate SP

G

 G-85

(J-6082-626-A)

         Assembly-6:  Installation Cautions of the Flexible Re-

tainer (LC) (600).

Flexible Retainer
(LC) (600)

Claws

Claws

Install the Flexible Retainer (LC) (600) while inserting four claws.

         Assembly-7:  Installation Cautions of the Lock Claw 

(LC).

Lock Claw (LC)

Install the lock Claw (LC) while inserting claw and boss.

Claw

Boss

         Assembly-8:  Installation Cautions of the ST Unit 

(75600).

ST Unit (75600)

Bottom Side

Claw A

Pass the harnesses.

Check to fit claw A

Claw B

         Assembly-9:  Installation Cautions of the Rec Button.

Rec Button

Rec Button

Install the Rec Button as shown.

Gate

NEX-7/7K_L2

3-2

         Assembly-10:  Installation Cautions of the Shield Tape 

(ST Flex) (600).

Install the Shield Tape (ST Flex) (600) as shown in the figure.

Shield Tape (ST FLEX) (600)

Bend sheet at edge 
of ST-265 board.

ST-265 board.

Upper View

Lower View

amount of 
gaps 0 to 1.0 mm

amount of 
gaps 0 to 1.0 mm

This portion does not float.

This portion does not float.

         Assembly-11:  Installation Cautions of the Insulating 

Sheet (ST) (600).

Install the Insulating Sheet (ST) (600) as shown in the figure.

Bend sheet at edge 
of ST-265 board.

Press this area

Insulating Sheet (ST) (600)

Upper View

Lower View

amount of 
gaps 0 to 0.5 mm

amount of 
gaps 0 to 0.5 mm

ST-265 board.

NEX-7/7K_L2

3-3E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

 OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

NEX-7/7K_L2

3-3E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

 OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310