DOWNLOAD Sony ILCE-7M2 / ILCE-7M2K (serv.man2) Service Manual ↓ Size: 13.33 MB | Pages: 22 in PDF or view online for FREE

ILCE-7M2/7M2K_L2

3-1

Assembly-1: Screw tightening sequence when assembling the 

Imager Unit

3

1

2

Assembly-2: Method of attachment of the MB Mask Sheet 

(5000)

Driver

Driver

1.6

MB Mask Sheet (5000)

MB Mask Sheet
Tape (5000)

MB N Frame (5000)

1.6

Assembly-3: Apply grease on the MB N Plate SP

MB N Plate SP

G G-85
(J-6082-626-A)

Assembly-4: Notes on Assembling the FP-2279 Flexible Board

valley fold
mountain fold

FP-2279 Flexible Board

Assembly-5: Notes on Assembling the AN-1006 Flexible Board

valley fold
mountain fold

AN-1006 Flexible Board

Terminal side

Assembly-6: Notes on Assembling the SH-1004 flexible board

SH-1004 flexible board

SH-1004 flexible board

MIC

Speaker

MIC

Rib

Boss

MIC

SH Base ASSY

Speaker

MIC

Bosses

Claw

Claw

valley fold
mountain fold

Assembly-7: Notes on Assembling the VM VF Lens ASSY and 

the NFC Block ASSY

VM Eye Sensor Cushion

When replacing to new VM VF Lens ASSY, 
remove the VM Eye Sensor Cushion of 
service parts and use the new VM VF Lens 
ASSY.

When replacing to new NFC Block ASSY, 

Change the position and direction of the harness 

as shown.

Red

Harness

Harness

Red

Black

Black

ILCE-7M2/7M2K_L2

3-2E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

1

 Souse the cleaning

 

cloth in ethyl alcohol.

2

 The dry cleaning cloth.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.

 OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

ILCE-7M2/7M2K_L2

3-2E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

1

 Souse the cleaning

 

cloth in ethyl alcohol.

2

 The dry cleaning cloth.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.

 OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

ILCE-7M2/7M2K_L2

3-2E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohol.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

1

 Souse the cleaning

 

cloth in ethyl alcohol.

2

 The dry cleaning cloth.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.

 OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310